Bosch Power Tools CLPK232-180, CLPK232-181, CLPK234-181L, CLPK233-181L, CLPK237-181 Operating Tips

Page 15

BM 2610027756 08-12_BM 2610027756 08-12.qxp 8/17/12 1:23 PM Page 15

Operating Tips

You will extend the life of your bits and do neater work if you always put the bit in contact with the work before pulling the trigger. During the operation, hold the tool firmly and exert light, steady pressure. Too much pressure at low speed will stall the tool. Too little pressure will keep the bit from cutting and cause excess friction by sliding over the surface. This can be damaging to both tool and bit.

DRILLING WITH VARIABLE SPEED

The trigger controlled variable speed feature will eliminate the need for center punches in hard materials. The variable speed trigger

allows you to slowly increase RPM. By using a slow starting speed, you are able to keep the bit from “wandering”. You can increase the speed as the bit “bites” into the work by squeezing the trigger.

DRIVING WITH VARIABLE SPEED

Variable speed drills will double as a power screwdriver by using a screwdriver bit in the drill mode. The technique is to start slowly, increasing the speed as the screw runs down. Set the screw snugly by slowing to a stop. Prior to driving screws, pilot and clearance holes should be drilled.

FASTENING WITH SCREWS

This procedure shown in (Fig. 12) will enable you to fasten materials together with your

Screw drills are available for screw sizes No. 6, 8, 10 and 12.

Cordless Drill/Screwdriver without stripping, splitting or separating the material.

First, clamp the pieces together and drill the first hole 2/3 the diameter of the screw. If the material is soft, drill only 2/3 the proper length. If it is hard, drill the entire length.

Second, unclamp the pieces and drill the second hole the same diameter as the screw shank in the first or top piece of wood.

Third, if flat head screw is used, countersink the hole to make the screw flush with the surface. Then, simply apply even pressure when driving the screw. The screw shank clearance hole in the first piece allows the screw head to pull the pieces tightly together.

FASTENING

WITH SCREWS

1.  Drill 2/3 diameter and 2/3 of screw length for

soft materials, full length for hard materials.

Screw

Apply a slight even pressure when driving screws.

2.  Drill same diameter as screw shank.

3.  Countersink same diameter as screw head.

Adjustable

Screw

Drill

The adjustable screw drill accessory will do all of these operations quickly and easily.

FIG. 12

DRILL BITS

Always inspect drill bits for excessive wear. Use only bits that are sharp and in good condition.

TWIST BITS: Available with straight and reduced shanks for wood and light duty metal drilling. High speed bits cut faster and last longer on hard materials.

CARBIDE TIPPED BITS: Used for drilling stone, concrete, plaster, cement and other

unusually hard nonmetals. Use continuous heavy feed pressure when employing carbide tip bits.

DRILLING WOOD

Be certain workpiece is clamped or anchored firmly. Always apply pressure in a straight line with the drill bit. Maintain enough pressure to keep the drill “biting”.

-15-

Image 15
Contents Leer antes de usar Call Toll Free forSee Voir Ver la página Personal safety General Power Tool Safety WarningsWork area safety Electrical safetySafety Rules for Cordless Drill/Drivers Battery tool use and careService Wear ear protectors when impact drilling Safety Rules for Cordless Hammer DrillsBattery/Charger Additional Safety WarningsLITHIUM-ION Batteries FCC CautionSymbol Name Designation/Explanation SymbolsSymbols Cordless Drill Drivers Cordless Hammer Drills Functional Description and SpecificationsOperating Instructions AssemblyDRILL/HAMMER Drill Selector Ring Gear Shifter Adjustable ClutchGear Shifting BrakeImportant Charging Notes Inserting and Releasing BATTERy PackCharger INDICATORS, SyMBOLS and Meaning Model BC630 Charging BATTERy Pack Model BC630Battery Pack Charger Charger INDICATORS, SyMBOLS and Meaning Model BC660 Charging BATTERy Pack Model BC660Battery Pack Charger Green Light Operating Tips Brushing Pressure Wire BrushesDrilling Metal Sanding and PolishingExtension Cords MaintenanceAccessories CleaningSécurité électrique Sécurité du lieu de travailEntretien Consignes de sécurité pour perceuses/tournevis sans cordonUtilisation et entretien des outils Électroportatifs Utilisation et entretien des outils à pilesPage Chargeur de pile Avertissements supplémentaires concernant la sécuritéPiles LITHIUM-ION Mise en garde de la FCCEntretien DES Piles Mise AU Rebut DES PilesSymbole Nom Désignation/Explication SymbolesSymboles suite Ouvertures DE Ventilation Mandrin Sans CLE Anneau DE Sélection DE ModeDescription fonctionnelle et spécifications Embrayage ReglableDouille DU Mandrin Foret PORTE-MECHE Embout DE Tournevis AssemblageConsignes de fonctionnement Insertion DES ForetsÉclairage D’APPOINT Intégré Changement DE VitessesChangement DE Vitesse Embrayage Reglable Embrayage Reglable FreinRemarques Importantes Concernant LA Charge Insertion ET Retrait DU BLOC-PILESTEMOINS, Symboles ET Signification Modèle BC630 Charge DU BLOC-PILES Modèle BC630BLOC-PILES Chargeur Voyant Voyant Rouge Vert TEMOINS, Symboles ET Signification Modèle BC660 Charge DU BLOC-PILES Modèle BC660BLOC-PILES Chargeur Green Light Consignes de fonctionnement Brosses Métalliques Perçage DES MétauxPerçage DE LA Maçonnerie Ponçage ET PolissageNettoyage AccessoiresEntretien Cordons de rallongeSeguridad del área de trabajo Seguridad eléctricaUso y cuidado de las herramientas Mecánicas Servicio de ajustes y reparaciones Uso y cuidado de las herramientas Alimentadas por bateríasNormas de seguridad para taladros de percusión sin cordón Batería/cargador Advertencias de seguridad adicionalesBaterías DE Iones DE Litio Aviso de precaución de la FCCCuidado DE LAS Baterías Eliminación DE LAS BateríasSímbolo Nombre Designación/explicación SímbolosSímbolos continuación Paquete de baterias Descripción funcional y especificacionesNúmero de modelo Capacidades máximasInstrucciones de funcionamiento EnsamblajeAnillo Selector DE Taladro / Taladro Cambio DE EngranajesEmbrague Ajustable Embrague Ajustable FrenoNotas Importantes Para Cargar Introducción Y Suelta DEL Paquete DE BateríasINDICADORES, Simbolos Y Significado Modelo BC630 Carga DEL Paquete DE Baterías Modelo BC630Paquete DE Baterías Cargador INDICADORES, Simbolos Y Significado Modelo BC660 Carga DEL Paquete DE Baterías Modelo BC660Paquete DE Baterías Cargador LUZ Verde Consejos de funcionamiento Escobillas DE Alambre Taladrado DE MetalTaladrado DE Mamposteria Lijado Y PulidoServicio MantenimientoCordones de extensión AccesoriosBM 2610027756 08-12BM 2610027756 08-12.qxp 8/17/12 124 PM Remarques Notas 2610027756