Atari 040-0050-01 manual Connect the Jamma Conversion Board and UVC, +5 VDC, +12 VDC, Ground

Page 17

Section 2 – Cabinet Conversion

3.Set jumper J8 on the Jamma conversion board to pins 1 and 2 for stereo, or pins 1 and 3 for mono audio, depending on how your cabinet audio is set up.

4.Place the boards next to each other in the service tray where you removed the old boards. Make sure that the Jamma connector on the Jamma wire harness can reach the Jamma Conversion Board before securing the boards to the cabinet.

5.Secure the boards with wood screws in the plastic feet.

Connect the Jamma Conversion Board and UVC

Figure 2. Typical Jamma Conversion Board and UVC Connections

Refer to the figure above, and Figure 5, Simplified Wiring Diagram, on page 43, and perform the following steps to connect the Jamma harness wiring and other cables to the Jamma Conversion Board:

1.Connect the Jamma connector from the Jamma harness to the Jamma edge on the Jamma Conversion Board.

2.Connect the Video Input, J4 on the Jamma Conversion Board to the video output port on the Video Converter board, if used, or to the VGA port on the computer video card.

3.Connect the existing PC power supply in the cabinet to the Jamma Conversion Board PWR IN port using the PC Y-power cable from the kit.

Note: The PC Y-power cable uses a standard PC power supply connection found on most DC power supplies used in arcade cabinets. If your existing power supply does not have this type of connector, you will need to splice the Y-Power cable into the power supply on the cabinet. Here are the specifications for the PC Y-power cable:

Red Wire

+5 VDC

 

Yellow Wire

+12 VDC

 

Black Wire

Ground

 

 

 

 

© 2004 GLOBAL VR®, INC.

040-0050-01 Rev. A 10/29/2004

Page 17 of 48

Image 17
Contents GvrSX Conversion Instructions System Manual Table of Figures Table of ContentsPreface Safety FCC Notices United States GvrSX provides the following benefits to operators GvrSX design showcases the following featuresGame Description Cabinet Conversion Upgrade StepsClean and Prepare the Cabinet Remove old Tournament Header and Card Reader Conversion Kit Contents and Replacement Parts List Artwork Optional Monitor Upgrade Kit Components PGA-UPGRADE-MTRCDs, Labels, and Manuals Adapt the Cabinet for the Larger Monitor Replace the Monitor OptionalRemove the Old Monitor Page Install the New Monitor Drilling Cabinet Air Holes Install the Cabinet Exhaust FanPage Set Up AC Power Distribution Set Up the HardwareRemove the Game PCB and Install New Hardware +5 VDC Connect the Jamma Conversion Board and UVC+12 VDC GroundHapp Ugci Board Connections Install the Happ Ugci BoardSet Up the Computer Connect the Computer Secure the Computer Apply Control Panel Graphics Upgrade the Control PanelPrepare the Control Panel Install Buttons and Connect Wiring Apply the Cabinet Graphics and Marquee Artwork Apply the Serial Number Sticker Run the Joystick Calibration Utility Power on and Test the CabinetUVC DIP Switch Settings Adjust the Universal Video Converter UVCSetting Game Options and Resets Using the Game Operator MenuMachine Menu Game Mode Menu All Audit Coin Stats Game Resets MenuAll Audit Game Stats All High Score StatsGame Purchase Audit Coin AuditsPlayer Control Test Game SelectionMonitor Calibration Test Starting a Game Information Bar Description Playing a Beach Head GameUSB Game Dongles Game Software CDs Operating System Restore CDSystem Software CDs Troubleshooting Video Problems TroubleshootingTroubleshooting Audio Problems Problem Possible Cause Possible SolutionTroubleshooting Computer Problems Troubleshooting Miscellaneous Problems Troubleshooting Control ProblemsTroubleshooting Configuration with New Wells-Gardner Monitor Diagrams and SchematicsDetailed Wiring Diagram Computer Rear Panel Diagram Computer Rear Panel DiagramWarranty Information Warranty ServicePage Technical Support