Atari 040-0050-01 manual Replace the Monitor Optional, Remove the Old Monitor

Page 10

Section 2 – Cabinet Conversion

Replace the Monitor (Optional)

Note: Do Not use the Universal Video Controller (UVC) board with the Wells Gardner® monitor.

If you have the Monitor Upgrade Kit, perform the steps in this section to remove the old monitor and install the 27-inch Wells-Gardner®monitor.

Remove the Old Monitor

1.Open the service shelf, and remove the glass display shield and monitor bezel.

2.Disconnect ALL wiring from the back of the monitor. Make sure that no wires still connected to the monitor are tied to the cabinet.

3.Remove the four (4) monitor retaining nuts and washers and save them for reinstallation.

4.Remove the monitor from the cabinet. It is advisable to have at least two people to support the weight of the monitor.

5.Proceed to the next section and install the new monitor.

Adapt the Cabinet for the Larger Monitor

If your cabinet already had a 27-inch monitor, you should be able to proceed to the next section and install the monitor.

If your cabinet had a 25-inch monitor, refer to the figure that follows, and perform the following steps to adapt the cabinet hardware for the larger, 27-inch Wells-Gardner®monitor:

1.Note the positioning of the lower monitor bracket to aid in reinstallation. Remove the nuts and bolts that secure the lower monitor bracket to the cabinet. Remove the bracket and save it for reinstallation. Perform the following steps to drill new bolt holes for the bracket to relocate it for the larger monitor.

2.Refer to the figure below and mark straight lines, as shown, through the center of the two sets of bolt holes and about 2" below. Drill two ¼" diameter bolt holes 1-7/16" below the original holes, and along the same centerline. Use the template from the kit (part #:

L-0059) to aid in placing the holes.

3.The overall distance between the bolt heads on the side of the cabinet must be 20-3/4" center-to-center in the long direction, and 1-9/16" center-to-center in the short direction.

gvrSX™ Conversion System Manual

 

Page 10 of 48

040-0050-01 Rev. A 10/29/2004

Page 9 Page 11
Image 10
Page 9 Page 11
Contents GvrSX Conversion Instructions System Manual Table of Contents Table of FiguresPreface Safety FCC Notices United States Game Description GvrSX design showcases the following featuresGvrSX provides the following benefits to operators Clean and Prepare the Cabinet Upgrade StepsCabinet Conversion Remove old Tournament Header and Card Reader Conversion Kit Contents and Replacement Parts List CDs, Labels, and Manuals Optional Monitor Upgrade Kit Components PGA-UPGRADE-MTRArtwork Remove the Old Monitor Replace the Monitor OptionalAdapt the Cabinet for the Larger Monitor Page Install the New Monitor Install the Cabinet Exhaust Fan Drilling Cabinet Air HolesPage Set Up the Hardware Set Up AC Power DistributionRemove the Game PCB and Install New Hardware +12 VDC Connect the Jamma Conversion Board and UVC+5 VDC GroundInstall the Happ Ugci Board Happ Ugci Board ConnectionsSet Up the Computer Connect the Computer Secure the Computer Prepare the Control Panel Upgrade the Control PanelApply Control Panel Graphics Install Buttons and Connect Wiring Apply the Cabinet Graphics and Marquee Artwork Apply the Serial Number Sticker Power on and Test the Cabinet Run the Joystick Calibration UtilityAdjust the Universal Video Converter UVC UVC DIP Switch SettingsUsing the Game Operator Menu Setting Game Options and ResetsMachine Menu Game Mode Menu All Audit Game Stats Game Resets MenuAll Audit Coin Stats All High Score StatsCoin Audits Game Purchase AuditGame Selection Player Control TestMonitor Calibration Test Starting a Game Playing a Beach Head Game Information Bar DescriptionUSB Game Dongles System Software CDs Operating System Restore CDGame Software CDs Troubleshooting Audio Problems TroubleshootingTroubleshooting Video Problems Problem Possible Cause Possible SolutionTroubleshooting Computer Problems Troubleshooting Control Problems Troubleshooting Miscellaneous ProblemsTroubleshooting Diagrams and Schematics Configuration with New Wells-Gardner MonitorDetailed Wiring Diagram Computer Rear Panel Diagram Computer Rear Panel DiagramWarranty Service Warranty InformationPage Technical Support
Top Page Image Contents