Omega CN1166 manual Program Define Mode Parameters

Page 78

Legend	Meaning		Ref.
Controller Set-Up Mode Parameters (Continued)		Volume	Section
	Output Power Maximum	II	2.1
	Output 1 Cycle Time	II	2.1
	Output 2 Cycle Time	II	2.1
	Process High Alarm 1 value	II	2.1
	Process Low Alarm 1 value	II	2.1
	Deviation Alarm 1 value	II	2.1
	Band Alarm 1 value	II	2.1
	Alarm 1 Hysteresis value	II	2.1
	Process High Alarm 2 value	II	2.1
	Process Low Alarm 2 value	II	2.1
	Deviation Alarm 2 value	II	2.1
	Band Alarm 2 value	II	2.1
	Alarm 2 Hysteresis value	II	2.1
	Decimal Point Position (for linear input range)	II	2.1
	Range Maximum (for linear input range)	II	2.1
	Range Minimum (for linear input range)	II	2.1
	Manual Power Selection enable/disable	II	2.1
	Setpoint Strategy	II	2.1
	Communications Write enable/disable	II	2.1
	Lock Code	II	2.1
	Program Define Mode Parameters
	Ramp Rate for Segment xx (xx in range 01 - 16)	II	3.2.2
	Segment xx is currently set as a Soak segment	II	3.2.2-3
	Segment xx is currently set as an End segment	II	3.2.2-3
	Final (Target) Setpoint value for Segment xx	II	3.2.2-3
	Segment Time for Segment xx	II	3.2.2-3
	Number of Cycles Programmed	II	3.2.4
	Timebase (hours/minutes or minutes/seconds)	II	3.2.4
	Guaranteed Soak Band value	II	3.2.4
	Event Marker setting for Segment xx	II	3.2.4
B-2	Volume II		S077-B

Image 78

Contents Page Page RAMP/SOAK Profile Volume Installation & Configuration Instructions Volume Operating InstructionsContents Unpacking Procedure PANEL-MOUNTING the ControllerConnections and Wiring Rear Terminal Connections Thermocouple Input Mains Line Input2 24V Nominal AC/DC Supply RTD InputsRelay Outputs Linear InputsRemote Run/Hold Input SSR Drive OutputsDC Outputs 11 RS485 Serial Communications LinkInternal Links and Switches Removing the Profile Controller from ITS HousingRemoving the Output 2/Output 3 Option PCBs Replacing the Instrument in ITS Housing REMOVING/REPLACING the Output 2/OUTPUT 3 Option PCBsSelection of Input Type and Output 1 Type Input TypePrimary Output Output 1 Type CPU PCB Relay/SSR Drive/Solid State OutputOutput 2 TYPE/OUTPUT 3 Type Entry Into Configuration Mode Hardware Definition CodeConfigurat ion Mode Wit h Hardw are Definit ion Code displayedOption Selection Hardware Definition Code Input/Output Type SelectionConfiguration Mode Parameters Wit h Hardw are Definit ion Code displayedParameter AL1 OFF, AL2 OFF Parameter Page Exit from Configuration Mode Base Mode Modbus Communications Controller SET-UP ModeProgram Definition Mode CREATING/EDITING a Program Alphabetic IndexBase Mode Display Sequence no Program RunningReleasing a Program from Hold Starting a ProgramPutting a Program in Hold Aborting a ProgramDisplay Sequence Program Running Read Only whilst Program is running/heldRaPID Control Feature PRE-TUNE FeatureEngaging Both PRE-TUNE and RaPID Features Indication of PRE-TUNE and RaPID StatusRaPID Status when Viewing the Hardware Definition Code Hardware Definition Code has the following significanceManual Control Press till front panel shows Press or to change display toController SET-UP Mode Lower display = Parameter Function Adjustment Range Default Value Parameter DetailsON/OFF Parameter Function Adjustment Range Default Value Power Alarm Operation Deviation Exit from Controller SET-UP Mode When this display showsProgram Definition Mode CREATING/EDITING a Program EntryCreating a Program Basic GuidelinesDefining Segments Rate Mode To make a Soak segmentDefining Segments Time Mode Program Options Guaranteed Soak Band T p o i n tSegment Event Status Press key To display Default Values and Adjustment Ranges Exit from Program Define ModeIntroduction Modbus Functions SupportedMessage Formats Read Coil Status Read n Bits 01/02 CRC16Read Holding Registers Read n Words 03/04 Force Single Coil Write 1 BitPreset Single Register Write 1 Word 06 B Loopback Diagnostic TestPreset Multiple Registers Write n Words 16 B Error and Exception Responses CRC16 CalculationReversed BIT Order Used Parameter Numbers Bit Parameters Controller Status ByteWord Parameters Controller ParametersInstrument ID Parameters Volume O077-4 Profiler Commands Profiler Status ByteUniversal Input GeneralInput Range Remote RUN/HOLD Input Option SSR Drive/TTL OutputRelay Solid StateTypes Available Relay, SSR drive, solid state and DC Solid State SSR Drive/TTL Alarm Control Loop ControlPerformance Reference ConditionsPerformance Under Reference Conditions S077-A Volume Environmental See PerformancePhysical Appendix B Summary of Displays Program Define Mode Parameters Configuration Mode Parameters AppendixC RaPID Control Feature AT OFF Alphabetical Index S077-IDX Volume Making a Soak Segment S077-IDX Volume Unpacking Procedure Word Parameters II/4-8