HP SSL1016 manual Attaching the autoloader to the front of the rack

Page 32

Installation and Configuration

9.Slide the autoloader in place 1 so that:

a.The mounting studs on the front ears of the autoloader slide into the holes between the clip nuts.

b.The front ears of the autoloader align with the front clips.

c.The rear support brackets engage the locking tab on the rear U-channel brackets.

1

2

2

Figure 12: Attaching the autoloader to the front of the rack

10.Loosely install a screw in each front clip nut to attach the ears 2.

11.Verify that the autoloader is level. Adjust as needed.

12.Tighten the four screws that attach the ears to the front clip nuts.

13.Tighten the four screws that connect the U-channel brackets to the rear clip nuts.

14.Install and tighten the four screws that connect the support brackets to the U-channel brackets.

32

SSL1016 Tape Autoloader Reference Guide

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Hp StorageWorks SSL1016 tape autoloader Page Contents Tape Cartridge Usage Autoloader Operation Tape Drive Cleaning Electrostatic Discharge Contents About this Guide Document Conventions Text SymbolsConventions Equipment Symbols Rack Stability Rack stability protects personal and equipmentGetting Help HP Technical SupportHP Storage Website HP Authorized ResellerAbout this Guide Overview1 Front ViewMailslot Function KeysMagazines Status LEDsOn/Off Button Cooling Fans AC Power PlugRear View Scsi Connection DCA SwitchesEthernet Connection Internal View PickerSupported Software Barcode ReaderOverview Preparation Scsi Bus RequirementsScsi Cable Length AccessoriesScsi Cable and Terminator Requirements Installation Location Required Tools and Hardware for Rackmount Installation RackmountingMeasuring with the rack template Installing the optional installation rails Attaching the autoloader support brackets Attaching the front rackmount handles Attaching the U-channel brackets to the rack Attaching the autoloader to the front of the rack Rear U-channel bracket screws Preparation Standalone InstallationRemoving the Autoloader From the Rack Installing the front standalone bracket covers ClearanceScsi Connection Attaching the cables Power On Daisy ChainingConnecting the power cord Configuration VerificationConfiguration submenu has the following options Scsi ID To set the Scsi ID On the main menu, scroll to Configuration Control Mode Select Change Mode Sequential Mode Operation Ethernet Autoloader IP AddressPress Enter On the Configuration submenu, scroll to Ethernet Subnet Mask Setting the Subnet Mask IP GatewaySetting the gateway address Snmp ServerSetting the Snmp server address Time ServerSetting the time server address TimePress Enter On the Configuration submenu, scroll to Time New timezone screen appears Security Set SecuritySet Passwords Select SecurityOn the Security submenu, scroll to Set Password Lost Passwords Installation and Configuration Tape Cartridge Usage Tape Cartridges DefinedTable.4 Sdlt 320 Supported Media Tape Cartridge Maintenance Inspecting Tape CartridgesOpening the cartridge door Checking the Sdlt tape leader DLTtape faulty leader situations Protecting Tape Cartridges Transporting Tape Cartridges Storing Tape CartridgesUsing the Write-Protect Switch DLT IV CartridgesWrite-Protect Switch Orange Position Indicator Result Write-protect switch, Sdlt Sdlt 320 CartridgeWrite-protect switch, Ultrium Ultrium Data CartridgeAutoloader Operation Front Panel ComponentsIndicator State Operating Condition LEDsMenu Tree Structure Setting Passwords Default Front Panel PasswordFront Panel Functionality LogoutUsing Data Cartridges Inserting a Single CartridgeInserting a cartridge into the mailslot Moving a Single Cartridge Ejecting a Single Cartridge Removing a Magazine Removing a magazine Installing a Magazine Installing a magazineInserting and Removing Cartridges Inserting a cartridgeManually Removing a Magazine Manually removing a magazineInside release latch Changing the Orientation Removing the screwsViewing Status Information Removing the handleAutoloader Status Select Autoloader InfoList of messages similar to the following screen appears View Firmware Version EDCView Element Status Element statusView Tape Drive Status Element status screenView Tape Drive Version Scsi IDRun Inventory View Ethernet InformationSet Data Compression Set CompressionImport/Export Slot Update FirmwareConfiguration On the Configuration submenu, scroll to I/E Slot Web Administration Web Administration HomeDefault Password ConfigurationView Status Information Move TapesMoving tapes using Web Administration Set to Home Run Diagnostic Tests Click View LogSet the System Time Setting system time Setting the Scsi ID Change the Scsi IDSet the Control Mode Setting the Control ModeSetting the compression Set the CompressionSet the Cleaning Mode Cleaning TapeSSL1016 Tape Autoloader Reference Guide 111 Set the Import/Export Slot Import/Export SlotSet Ethernet Configurations Networking options114 Set Security Option Security optionSet Passwords Update the Firmware Get system updatesAutoloader Operation 118 Tape Drive Cleaning Configuring the Cleaning Tape LocationInserting the Cleaning Tape Storing the Cleaning TapeScroll to the slot where you want to store the cleaning tape Manual Cleaning Ejecting the Cleaning TapeTape Drive Cleaning Methods SSL1016 Tape Autoloader Reference Guide 123 Auto Clean Software Tape Drive Cleaning 126 Operational Problems Before Contacting Technical SupportFile system Error Messages Understanding Error Messages Error Message Description Suggested Repair 132 Pieces of media fail, contact HP customer support 134 Destination element 136 SSL1016 Tape Autoloader Reference Guide 137 Diagnostic Tests Lists the diagnostic testsFederal Communications Commission Notice Class a EquipmentCables Class B EquipmentModifications Canadian Notice Avis Canadien European Union Notice Bsmi NoticeJapanese Notice Regulatory Compliance Notices 144 Electrostatic Discharge Grounding Methods Physical Specifications Performance SpecificationsPower Specifications Environmental Specifications Acoustic and Noise LimitsSafety and Regulatory Description SpecificationConfiguration and Tools Removing a DCARemoving the screws on the rear of the chassis Removing the DCA Bottom of DCA Installing a DCA Installing the DCAUpgrading or Replacing the DCA 156 Index Index Scsi Index 160
Related manuals
Manual 8 pages 15.98 Kb
Top Page Image Contents