HP NetServer 5971-0821 manual 100

Page 106

100

Image 106

Contents HP Part Number Audience Assumptions Contents Microsoft Windows 2000 Installation Novell NetWare InstallationSCO UnixWare Installation SCO OpenServer InstallationLinux Support Product Specifications Troubleshooting 101 Regulatory Information 103 Warranty and Support 109Index 111 Installation and Setup HP Ultra3 Single Channel Scsi Host Bus AdapterBus Segments on the HP Ultra3 Scsi Host Adapter Primary and Secondary Bus SegmentsInstalling the HP Ultra3 Scsi Host Bus Adapter Bit and 64-bit Expansion SlotsHost Bus Adapter Installed in 64-bit Slot Check the Scsi IDs Setting Up Scsi DevicesChoosing Scsi Cables Terminate the EndsPage Connecting Scsi Devices Connecting the Scsi Host Adapter to the Common TrayConnecting the Scsi Host Adapter to a Hot-Plug Cage Common Tray Cable ConnectionConnecting Ultra/Fast Wide Scsi Devices Hot-Plug Cage Cable ConnectionsConnecting Internal Ultra/Fast Narrow Devices Connecting Ultra/Fast Wide Scsi DevicesConnecting External Scsi Devices Connecting Ultra/Fast Narrow Devices10. Connecting External Scsi Devices Preloaded Ultra3 Drivers HP Ultra3 Scsi Host Adapter Driver SoftwareEmbedded Ultra3 Drivers Troubleshooting Boot Device Options Configuration with SCSISelectScsi Device Configuration Advanced Configuration Options SCSISelect Options Available Default SettingsStarting SCSISelect Exiting SCSISelect Using SCSISelect SettingsScsi Bus Interface Definitions Boot Device Options Scsi Device ConfigurationAdvanced Configuration Options Page Page Using Scsi Disk Utilities Installing the Driver When Installing Windows NT Microsoft Windows NT InstallationAdaptec Ultra3 PCI Scsi Controller NT4.0 Installing the Driver When Windows NT is Already Installed Completing a Fresh Windows NT 4.0 Installation From CD-ROMUsing Advanced Configuration Parameters Updating Windows NTUsing Windows NT Scsi Parameters RegdwordUsing Driver-specific Parameters Page Hot-Plug PCI Feature Type a\nt4\hotp160m.reg and press EnterUsing Windows NT and the Host Adapter Removing a Host AdapterProblems and Solutions Removing a Host Adapter in Windows NTError Messages Press spacebar NOW to invoke the Last Known Good menuXxxxx011 Error issuing command Adpu160m.sys Error MessagesXxxxx010 Error issuing command Xxxxx021 Target device protocol errorXxxxx031 Target device queue full Xxxxx023 Target device parity errorXxxxx024 Data overrun or underrun Xxxxx032 Target device busyXxxxx097 Unable to allocate memory Xxxxxd4 Adapter hardware failure adapter resetXxxxx0d6 Internal driver error Xxxxx0ce Scatter/gather limit exceededPage Installing the Driver When Installing Windows Microsoft Windows 2000 InstallationPress any key to boot from CD Click the Control Panel Using Windows 2000 Scsi Parameters Regdword Regsz Troubleshooting Problems and Solutions Driver Error Messages Xxxxx021 Target device protocol error Xxxxx089 Unable to allocate memory Xxxxxd4 Adapter hardware failure adapter reset Page Download the Nwpa Update Package Novell NetWare InstallationInstalling the Driver When Installing NetWare NetWare 3.12/3.2Copy cdrom.nlm to c\server.312\cdsave Lswap loader.exe \server.312\server.exe cd \server.312NetWare 4.12/4.2 Load c\server.312\adpt160m slot=2NetWare Select Save parameter and continue, and press EnterInstall CD-ROM Drivers on a DOS Bootable Hard Disk DOS Drivers for CD-ROM AccessMkdir c\scsi Copy a\dos\*.* c\scsi Installing the Driver When NetWare is Already Installed Load pathnameadpt160m optionsLoad pathnameadpt160m.ham options Loading the Driver at Server BootupUsing the Load Command Line Options Load c\nwserver\adpt160m verbose=yAdpt160m.ham Command Line Options Option Values Default DescriptionMultluntargets= Bit Mask Options Binary HexUsing Removable Media Using NetWare and the Host AdapterSample Load Commands Load a\netware\adpt160m.hamMount Status Lock StatusUsing a CD-ROM with NetWare Using the NetWare Tape BackupLoad pathnameadpt160m Cd device list Optimizing PerformanceScan all luns Cd mount x nameXxxxx080 Unable to allocate memory Xxxxx081 Adapter software initialization failurePage Xxxxx0ac Driver already loaded for all host bus adapters Xxxxx0a4 Scsi bus reset by third party hardwareXxxxx0c9 Invalid command line parameter Xxxxx0a9 Possible interrupt conflictPage Installing the Driver When Installing SCO OpenServer SCO OpenServer InstallationInstalling SCO OpenServer When you see these prompts Umount /stand Name Description Host Logical Bus Adapter Device Unit Prefix Type NumberEnter Using SCO OpenServer and the Host Adapter Using Multiple Host AdaptersUsing Wide Scsi Host Adapters and Devices Setting ParametersChanging the Boot Disk Using Tunable Parameters for the ad160 DriverChanging the Maximum Number of LUNs Supported Enabling Scatter/Gather and Tagged QueuingMy computer does not recognize my Scsi devices My computer does not recognize my host adapterAm having problems booting the computer from a Scsi drive Ad160 Sdsk My computer crashes or displays panic messages at boot time My computer hangs during heavy system load activityType Y to rebuild the kernel environment Reboot the system Xxxxx0ca Cannot initialize device Page SCO UnixWare Installation Installing the Driver When Installing UnixWareInstalling the Driver When UnixWare is Already Installed Load the Package Back Up the ComputerPkgadd -d diskette1 Type pkginfo -l adstxx and press Enter Modify the New System FileRebuild the UnixWare Kernel Cat /etc/conf/sdevice.d/adst21Cd /etc/conf/bin Idbuild -B Using UnixWare and the Host AdapterBoot the New Kernel Cd /etc/conf/cf.d cp unix /stand/unix cd Shutdown -g0Removing the Driver Using Tunable ParametersEtc/conf/bin/idbuild -B Cp /etc/conf/cf.d/unix /stand/unix Etc/conf/bin/idinstall -d adst21 Etc/conf/bin/idinstall -d adst70Troubleshooting Xxxxx011 Error issuing command Adapter was given more or less data than was expected Xxxxx046 Target device did not respond to abort sequence Xxxxx097 Unable to allocate memory Linux Support Linux Operating System World Wide Web URLPage Product Specifications ElectricalPhysical EnvironmentalRegulatory 100 Common Error Messages TroubleshootingTroubleshooting Checklist Device connected, but not readyTime-out failure during … Start unit request failed102 Federal Communications Commission Regulatory InformationRegulatory Notices Electromagnetic Compliance Class B EquipmentClass a Equipment Class a Accessories104 For products labeled as Class a For products labeled as Class B105 106 Class a Warning 107 Declaration of Conformity US, EU, Australia 108Hewlett-Packard Hardware Accessories Warranty and SupportHardware Accessories Limited Warranty 109Third-Party Hardware Products HP Repair and Telephone SupportWorld Wide Web CanadaIndex 111112 113 114