HP NetServer 5971-0821 manual

Page 26

•Reset SCSI Bus at IC Initialization—(Default:Enabled) When set to Enabled, the SCSI host bus adapter generates a SCSI bus reset during its power-on initialization and after a hard reset.

•Display <Ctrl> <A> Messages during BIOS Initialization—(Default:Enabled) When set to Enabled, the SCSI host bus adapter BIOS displays the Press <Ctrl> <A> for SCSISelect (TM) Utility! message on your screen during system bootup. If this setting is disabled, you can still invoke the SCSISelect Utility by pressing <Ctrl> <A> after the SCSI host bus adapter BIOS banner appears.

•Extended BIOS Translation for DOS Drives > 1 GByte—(Default:Enabled) When set to Enabled, provides an extended translation scheme for SCSI hard disks with capacities greater than 1 GByte. This setting is necessary only for MS-DOS 5.0 or above; it is not required for other operating systems, such as NetWare or UNIX.

CAUTION Changing the translation scheme destroys all data on the drive. Be sure to back up the data before changing the translation scheme.

Use the MS-DOS Fdisk command to partition a disk larger than 1 GByte controlled by the SCSI host bus adapter BIOS, when using DOS, Windows 3.1.x, or Windows 95/98.

•Verbose/Silent Mode—(Default: Verbose) When set Verbose, the SCSI host bus adapter BIOS displays the host adapter model on the screen during system bootup. When set to Silent, the message will not be displayed during bootup.

•Host Adapter BIOS (Configuration Utility Reserves BIOS Space)— (Default: Enabled) Enables or disables the SCSI host bus adapter BIOS.

Leave at Enabled to allow the SCSI host bus adapter BIOS to scan and initialize all SCSI devices.

Set to Disabled: Not scan if the devices on the SCSI bus (for

example, CD-ROM drives) are controlled by software drivers and do not

need the BIOS, and you do not want the BIOS to scan the SCSI bus.

Set to Disabled: Scan Bus if you do not need the BIOS, but you want it to scan the SCSI devices on the bus.

20

Image 26

Contents HP Part Number Audience Assumptions Contents Microsoft Windows 2000 Installation Novell NetWare InstallationLinux Support Product Specifications Troubleshooting 101 SCO OpenServer InstallationSCO UnixWare Installation Index 111 Warranty and Support 109Regulatory Information 103 Installation and Setup HP Ultra3 Single Channel Scsi Host Bus AdapterBus Segments on the HP Ultra3 Scsi Host Adapter Primary and Secondary Bus SegmentsInstalling the HP Ultra3 Scsi Host Bus Adapter Bit and 64-bit Expansion SlotsHost Bus Adapter Installed in 64-bit Slot Check the Scsi IDs Setting Up Scsi DevicesChoosing Scsi Cables Terminate the EndsPage Connecting Scsi Devices Connecting the Scsi Host Adapter to the Common TrayConnecting the Scsi Host Adapter to a Hot-Plug Cage Common Tray Cable ConnectionConnecting Ultra/Fast Wide Scsi Devices Hot-Plug Cage Cable ConnectionsConnecting Internal Ultra/Fast Narrow Devices Connecting Ultra/Fast Wide Scsi DevicesConnecting External Scsi Devices Connecting Ultra/Fast Narrow Devices10. Connecting External Scsi Devices Embedded Ultra3 Drivers HP Ultra3 Scsi Host Adapter Driver SoftwarePreloaded Ultra3 Drivers Troubleshooting Scsi Device Configuration Configuration with SCSISelectBoot Device Options Starting SCSISelect SCSISelect Options Available Default SettingsAdvanced Configuration Options Scsi Bus Interface Definitions Using SCSISelect SettingsExiting SCSISelect Boot Device Options Scsi Device ConfigurationAdvanced Configuration Options Page Page Using Scsi Disk Utilities Adaptec Ultra3 PCI Scsi Controller NT4.0 Microsoft Windows NT InstallationInstalling the Driver When Installing Windows NT Installing the Driver When Windows NT is Already Installed Completing a Fresh Windows NT 4.0 Installation From CD-ROMUsing Advanced Configuration Parameters Updating Windows NTUsing Windows NT Scsi Parameters RegdwordUsing Driver-specific Parameters Page Hot-Plug PCI Feature Type a\nt4\hotp160m.reg and press EnterUsing Windows NT and the Host Adapter Removing a Host AdapterProblems and Solutions Removing a Host Adapter in Windows NTError Messages Press spacebar NOW to invoke the Last Known Good menuXxxxx011 Error issuing command Adpu160m.sys Error MessagesXxxxx010 Error issuing command Xxxxx021 Target device protocol errorXxxxx031 Target device queue full Xxxxx023 Target device parity errorXxxxx024 Data overrun or underrun Xxxxx032 Target device busyXxxxx097 Unable to allocate memory Xxxxxd4 Adapter hardware failure adapter resetXxxxx0d6 Internal driver error Xxxxx0ce Scatter/gather limit exceededPage Press any key to boot from CD Microsoft Windows 2000 InstallationInstalling the Driver When Installing Windows Click the Control Panel Using Windows 2000 Scsi Parameters Regdword Regsz Troubleshooting Problems and Solutions Driver Error Messages Xxxxx021 Target device protocol error Xxxxx089 Unable to allocate memory Xxxxxd4 Adapter hardware failure adapter reset Page Download the Nwpa Update Package Novell NetWare InstallationInstalling the Driver When Installing NetWare NetWare 3.12/3.2Copy cdrom.nlm to c\server.312\cdsave Lswap loader.exe \server.312\server.exe cd \server.312NetWare 4.12/4.2 Load c\server.312\adpt160m slot=2NetWare Select Save parameter and continue, and press EnterMkdir c\scsi Copy a\dos\*.* c\scsi DOS Drivers for CD-ROM AccessInstall CD-ROM Drivers on a DOS Bootable Hard Disk Installing the Driver When NetWare is Already Installed Load pathnameadpt160m optionsLoad pathnameadpt160m.ham options Loading the Driver at Server BootupUsing the Load Command Line Options Load c\nwserver\adpt160m verbose=yAdpt160m.ham Command Line Options Option Values Default DescriptionMultluntargets= Bit Mask Options Binary HexUsing Removable Media Using NetWare and the Host AdapterSample Load Commands Load a\netware\adpt160m.hamMount Status Lock StatusLoad pathnameadpt160m Using the NetWare Tape BackupUsing a CD-ROM with NetWare Cd device list Optimizing PerformanceScan all luns Cd mount x nameXxxxx080 Unable to allocate memory Xxxxx081 Adapter software initialization failurePage Xxxxx0ac Driver already loaded for all host bus adapters Xxxxx0a4 Scsi bus reset by third party hardwareXxxxx0c9 Invalid command line parameter Xxxxx0a9 Possible interrupt conflictPage Installing SCO OpenServer SCO OpenServer InstallationInstalling the Driver When Installing SCO OpenServer When you see these prompts Umount /stand Name Description Host Logical Bus Adapter Device Unit Prefix Type NumberEnter Using SCO OpenServer and the Host Adapter Using Multiple Host AdaptersUsing Wide Scsi Host Adapters and Devices Setting ParametersChanging the Boot Disk Using Tunable Parameters for the ad160 DriverChanging the Maximum Number of LUNs Supported Enabling Scatter/Gather and Tagged QueuingMy computer does not recognize my Scsi devices My computer does not recognize my host adapterAm having problems booting the computer from a Scsi drive Ad160 Sdsk My computer crashes or displays panic messages at boot time My computer hangs during heavy system load activityType Y to rebuild the kernel environment Reboot the system Xxxxx0ca Cannot initialize device Page SCO UnixWare Installation Installing the Driver When Installing UnixWareInstalling the Driver When UnixWare is Already Installed Pkgadd -d diskette1 Back Up the ComputerLoad the Package Type pkginfo -l adstxx and press Enter Modify the New System FileRebuild the UnixWare Kernel Cat /etc/conf/sdevice.d/adst21Cd /etc/conf/bin Idbuild -B Using UnixWare and the Host AdapterBoot the New Kernel Cd /etc/conf/cf.d cp unix /stand/unix cd Shutdown -g0Etc/conf/bin/idbuild -B Cp /etc/conf/cf.d/unix /stand/unix Using Tunable ParametersRemoving the Driver Etc/conf/bin/idinstall -d adst21 Etc/conf/bin/idinstall -d adst70Troubleshooting Xxxxx011 Error issuing command Adapter was given more or less data than was expected Xxxxx046 Target device did not respond to abort sequence Xxxxx097 Unable to allocate memory Linux Support Linux Operating System World Wide Web URLPage Product Specifications ElectricalPhysical EnvironmentalRegulatory 100 Common Error Messages TroubleshootingTroubleshooting Checklist Device connected, but not ready102 Start unit request failedTime-out failure during … Federal Communications Commission Regulatory InformationRegulatory Notices Electromagnetic Compliance Class B Equipment104 Class a AccessoriesClass a Equipment 105 For products labeled as Class BFor products labeled as Class a 106 Class a Warning 107 Declaration of Conformity US, EU, Australia 108Hewlett-Packard Hardware Accessories Warranty and SupportHardware Accessories Limited Warranty 109Third-Party Hardware Products HP Repair and Telephone SupportWorld Wide Web CanadaIndex 111112 113 114