HP NetServer 5971-0821 manual Installing the HP Ultra3 Scsi Host Bus Adapter

Page 9

Installing the HP Ultra3 SCSI Host Bus Adapter

1.Discharge any static electricity build-up before handling the SCSI host bus adapter by touching a grounded metal object (like the exposed metal parts on the back of your HP Netserver).

WARNING Turn OFF power to the HP Netserver and disconnect the power cord.

2.After you turn off your HP Netserver and unplug the power cord, remove the cover from the Netserver.

32-bit PCI Slot

64-bit PCI Slot

Figure 1-3. 32-bit and 64-bit Expansion Slots

3.Locate an unused 64-bit PCI expansion slot and remove the expansion slot cover. If the HP Netserver does not have a 64-bit slot, you can install the host adapter in a 32-bit PCI slot. (The expansion slot must be compliant with PCI Rev. 2.1 or higher and must support Bus Mastering.)

3

Image 9
Contents HP Part Number Audience Assumptions Contents Novell NetWare Installation Microsoft Windows 2000 InstallationSCO OpenServer Installation SCO UnixWare InstallationLinux Support Product Specifications Troubleshooting 101 Warranty and Support 109 Regulatory Information 103Index 111 HP Ultra3 Single Channel Scsi Host Bus Adapter Installation and SetupPrimary and Secondary Bus Segments Bus Segments on the HP Ultra3 Scsi Host AdapterBit and 64-bit Expansion Slots Installing the HP Ultra3 Scsi Host Bus AdapterHost Bus Adapter Installed in 64-bit Slot Choosing Scsi Cables Setting Up Scsi DevicesCheck the Scsi IDs Terminate the EndsPage Connecting the Scsi Host Adapter to the Common Tray Connecting Scsi DevicesCommon Tray Cable Connection Connecting the Scsi Host Adapter to a Hot-Plug CageHot-Plug Cage Cable Connections Connecting Ultra/Fast Wide Scsi DevicesConnecting Ultra/Fast Wide Scsi Devices Connecting Internal Ultra/Fast Narrow DevicesConnecting Ultra/Fast Narrow Devices Connecting External Scsi Devices10. Connecting External Scsi Devices HP Ultra3 Scsi Host Adapter Driver Software Preloaded Ultra3 DriversEmbedded Ultra3 Drivers Troubleshooting Configuration with SCSISelect Boot Device OptionsScsi Device Configuration SCSISelect Options Available Default Settings Advanced Configuration OptionsStarting SCSISelect Using SCSISelect Settings Exiting SCSISelectScsi Bus Interface Definitions Scsi Device Configuration Boot Device OptionsAdvanced Configuration Options Page Page Using Scsi Disk Utilities Microsoft Windows NT Installation Installing the Driver When Installing Windows NTAdaptec Ultra3 PCI Scsi Controller NT4.0 Completing a Fresh Windows NT 4.0 Installation From CD-ROM Installing the Driver When Windows NT is Already InstalledUpdating Windows NT Using Advanced Configuration ParametersRegdword Using Windows NT Scsi ParametersUsing Driver-specific Parameters Page Type a\nt4\hotp160m.reg and press Enter Hot-Plug PCI FeatureRemoving a Host Adapter Using Windows NT and the Host AdapterRemoving a Host Adapter in Windows NT Problems and SolutionsPress spacebar NOW to invoke the Last Known Good menu Error MessagesXxxxx010 Error issuing command Adpu160m.sys Error MessagesXxxxx011 Error issuing command Xxxxx021 Target device protocol errorXxxxx024 Data overrun or underrun Xxxxx023 Target device parity errorXxxxx031 Target device queue full Xxxxx032 Target device busyXxxxx0d6 Internal driver error Xxxxxd4 Adapter hardware failure adapter resetXxxxx097 Unable to allocate memory Xxxxx0ce Scatter/gather limit exceededPage Microsoft Windows 2000 Installation Installing the Driver When Installing WindowsPress any key to boot from CD Click the Control Panel Using Windows 2000 Scsi Parameters Regdword Regsz Troubleshooting Problems and Solutions Driver Error Messages Xxxxx021 Target device protocol error Xxxxx089 Unable to allocate memory Xxxxxd4 Adapter hardware failure adapter reset Page Installing the Driver When Installing NetWare Novell NetWare InstallationDownload the Nwpa Update Package NetWare 3.12/3.2Lswap loader.exe \server.312\server.exe cd \server.312 Copy cdrom.nlm to c\server.312\cdsaveLoad c\server.312\adpt160m slot=2 NetWare 4.12/4.2Select Save parameter and continue, and press Enter NetWareDOS Drivers for CD-ROM Access Install CD-ROM Drivers on a DOS Bootable Hard DiskMkdir c\scsi Copy a\dos\*.* c\scsi Load pathnameadpt160m options Installing the Driver When NetWare is Already InstalledUsing the Load Command Line Options Loading the Driver at Server BootupLoad pathnameadpt160m.ham options Load c\nwserver\adpt160m verbose=yOption Values Default Description Adpt160m.ham Command Line OptionsMultluntargets= Binary Hex Bit Mask OptionsSample Load Commands Using NetWare and the Host AdapterUsing Removable Media Load a\netware\adpt160m.hamLock Status Mount StatusUsing the NetWare Tape Backup Using a CD-ROM with NetWareLoad pathnameadpt160m Scan all luns Optimizing PerformanceCd device list Cd mount x nameXxxxx081 Adapter software initialization failure Xxxxx080 Unable to allocate memoryPage Xxxxx0c9 Invalid command line parameter Xxxxx0a4 Scsi bus reset by third party hardwareXxxxx0ac Driver already loaded for all host bus adapters Xxxxx0a9 Possible interrupt conflictPage SCO OpenServer Installation Installing the Driver When Installing SCO OpenServerInstalling SCO OpenServer When you see these prompts Umount /stand Name Description Logical Bus Adapter Device Unit Prefix Type Number HostEnter Using Multiple Host Adapters Using SCO OpenServer and the Host AdapterChanging the Boot Disk Setting ParametersUsing Wide Scsi Host Adapters and Devices Using Tunable Parameters for the ad160 DriverEnabling Scatter/Gather and Tagged Queuing Changing the Maximum Number of LUNs SupportedMy computer does not recognize my host adapter My computer does not recognize my Scsi devicesAm having problems booting the computer from a Scsi drive Ad160 Sdsk My computer hangs during heavy system load activity My computer crashes or displays panic messages at boot timeType Y to rebuild the kernel environment Reboot the system Xxxxx0ca Cannot initialize device Page Installing the Driver When Installing UnixWare SCO UnixWare InstallationInstalling the Driver When UnixWare is Already Installed Back Up the Computer Load the PackagePkgadd -d diskette1 Rebuild the UnixWare Kernel Modify the New System FileType pkginfo -l adstxx and press Enter Cat /etc/conf/sdevice.d/adst21Boot the New Kernel Using UnixWare and the Host AdapterCd /etc/conf/bin Idbuild -B Cd /etc/conf/cf.d cp unix /stand/unix cd Shutdown -g0Using Tunable Parameters Removing the DriverEtc/conf/bin/idbuild -B Cp /etc/conf/cf.d/unix /stand/unix Etc/conf/bin/idinstall -d adst70 Etc/conf/bin/idinstall -d adst21Troubleshooting Xxxxx011 Error issuing command Adapter was given more or less data than was expected Xxxxx046 Target device did not respond to abort sequence Xxxxx097 Unable to allocate memory Linux Operating System World Wide Web URL Linux SupportPage Electrical Product SpecificationsEnvironmental PhysicalRegulatory 100 Troubleshooting Checklist TroubleshootingCommon Error Messages Device connected, but not readyStart unit request failed Time-out failure during …102 Regulatory Notices Electromagnetic Compliance Regulatory InformationFederal Communications Commission Class B EquipmentClass a Accessories Class a Equipment104 For products labeled as Class B For products labeled as Class a105 106 Class a Warning 107 108 Declaration of Conformity US, EU, AustraliaHardware Accessories Limited Warranty Warranty and SupportHewlett-Packard Hardware Accessories 109World Wide Web HP Repair and Telephone SupportThird-Party Hardware Products Canada111 Index112 113 114