HP NetServer 5971-0821 manual Class B Equipment, 106

Page 112

radio interference may be caused. In this case, you may need to take appropriate corrective actions.

Notice for Korea

The equipment you have purchased may be in either the class A or class B category.

Class A Equipment:

Please note that this equipment has been approved for business purposes with regard to electromagnetic interference. If purchased in error for use in a residential area, you may wish to exchange the equipment where you purchased it.

Class B Equipment:

Please note that this equipment has been approved for non-business purposes with regards to electromagnetic interference. This equipment can be allowed for use in all areas as well as residential areas.

106

Image 112

Contents HP Part Number Audience Assumptions Contents Microsoft Windows 2000 Installation Novell NetWare InstallationSCO UnixWare Installation SCO OpenServer InstallationLinux Support Product Specifications Troubleshooting 101 Regulatory Information 103 Warranty and Support 109Index 111 Installation and Setup HP Ultra3 Single Channel Scsi Host Bus AdapterBus Segments on the HP Ultra3 Scsi Host Adapter Primary and Secondary Bus SegmentsInstalling the HP Ultra3 Scsi Host Bus Adapter Bit and 64-bit Expansion SlotsHost Bus Adapter Installed in 64-bit Slot Setting Up Scsi Devices Choosing Scsi CablesCheck the Scsi IDs Terminate the EndsPage Connecting Scsi Devices Connecting the Scsi Host Adapter to the Common TrayConnecting the Scsi Host Adapter to a Hot-Plug Cage Common Tray Cable ConnectionConnecting Ultra/Fast Wide Scsi Devices Hot-Plug Cage Cable ConnectionsConnecting Internal Ultra/Fast Narrow Devices Connecting Ultra/Fast Wide Scsi DevicesConnecting External Scsi Devices Connecting Ultra/Fast Narrow Devices10. Connecting External Scsi Devices Preloaded Ultra3 Drivers HP Ultra3 Scsi Host Adapter Driver SoftwareEmbedded Ultra3 Drivers Troubleshooting Boot Device Options Configuration with SCSISelectScsi Device Configuration Advanced Configuration Options SCSISelect Options Available Default SettingsStarting SCSISelect Exiting SCSISelect Using SCSISelect SettingsScsi Bus Interface Definitions Boot Device Options Scsi Device ConfigurationAdvanced Configuration Options Page Page Using Scsi Disk Utilities Installing the Driver When Installing Windows NT Microsoft Windows NT InstallationAdaptec Ultra3 PCI Scsi Controller NT4.0 Installing the Driver When Windows NT is Already Installed Completing a Fresh Windows NT 4.0 Installation From CD-ROMUsing Advanced Configuration Parameters Updating Windows NTUsing Windows NT Scsi Parameters RegdwordUsing Driver-specific Parameters Page Hot-Plug PCI Feature Type a\nt4\hotp160m.reg and press EnterUsing Windows NT and the Host Adapter Removing a Host AdapterProblems and Solutions Removing a Host Adapter in Windows NTError Messages Press spacebar NOW to invoke the Last Known Good menuAdpu160m.sys Error Messages Xxxxx010 Error issuing commandXxxxx011 Error issuing command Xxxxx021 Target device protocol errorXxxxx023 Target device parity error Xxxxx024 Data overrun or underrunXxxxx031 Target device queue full Xxxxx032 Target device busyXxxxxd4 Adapter hardware failure adapter reset Xxxxx0d6 Internal driver errorXxxxx097 Unable to allocate memory Xxxxx0ce Scatter/gather limit exceededPage Installing the Driver When Installing Windows Microsoft Windows 2000 InstallationPress any key to boot from CD Click the Control Panel Using Windows 2000 Scsi Parameters Regdword Regsz Troubleshooting Problems and Solutions Driver Error Messages Xxxxx021 Target device protocol error Xxxxx089 Unable to allocate memory Xxxxxd4 Adapter hardware failure adapter reset Page Novell NetWare Installation Installing the Driver When Installing NetWareDownload the Nwpa Update Package NetWare 3.12/3.2Copy cdrom.nlm to c\server.312\cdsave Lswap loader.exe \server.312\server.exe cd \server.312NetWare 4.12/4.2 Load c\server.312\adpt160m slot=2NetWare Select Save parameter and continue, and press EnterInstall CD-ROM Drivers on a DOS Bootable Hard Disk DOS Drivers for CD-ROM AccessMkdir c\scsi Copy a\dos\*.* c\scsi Installing the Driver When NetWare is Already Installed Load pathnameadpt160m optionsLoading the Driver at Server Bootup Using the Load Command Line OptionsLoad pathnameadpt160m.ham options Load c\nwserver\adpt160m verbose=yAdpt160m.ham Command Line Options Option Values Default DescriptionMultluntargets= Bit Mask Options Binary HexUsing NetWare and the Host Adapter Sample Load CommandsUsing Removable Media Load a\netware\adpt160m.hamMount Status Lock StatusUsing a CD-ROM with NetWare Using the NetWare Tape BackupLoad pathnameadpt160m Optimizing Performance Scan all lunsCd device list Cd mount x nameXxxxx080 Unable to allocate memory Xxxxx081 Adapter software initialization failurePage Xxxxx0a4 Scsi bus reset by third party hardware Xxxxx0c9 Invalid command line parameterXxxxx0ac Driver already loaded for all host bus adapters Xxxxx0a9 Possible interrupt conflictPage Installing the Driver When Installing SCO OpenServer SCO OpenServer InstallationInstalling SCO OpenServer When you see these prompts Umount /stand Name Description Host Logical Bus Adapter Device Unit Prefix Type NumberEnter Using SCO OpenServer and the Host Adapter Using Multiple Host AdaptersSetting Parameters Changing the Boot DiskUsing Wide Scsi Host Adapters and Devices Using Tunable Parameters for the ad160 DriverChanging the Maximum Number of LUNs Supported Enabling Scatter/Gather and Tagged QueuingMy computer does not recognize my Scsi devices My computer does not recognize my host adapterAm having problems booting the computer from a Scsi drive Ad160 Sdsk My computer crashes or displays panic messages at boot time My computer hangs during heavy system load activityType Y to rebuild the kernel environment Reboot the system Xxxxx0ca Cannot initialize device Page SCO UnixWare Installation Installing the Driver When Installing UnixWareInstalling the Driver When UnixWare is Already Installed Load the Package Back Up the ComputerPkgadd -d diskette1 Modify the New System File Rebuild the UnixWare KernelType pkginfo -l adstxx and press Enter Cat /etc/conf/sdevice.d/adst21Using UnixWare and the Host Adapter Boot the New KernelCd /etc/conf/bin Idbuild -B Cd /etc/conf/cf.d cp unix /stand/unix cd Shutdown -g0Removing the Driver Using Tunable ParametersEtc/conf/bin/idbuild -B Cp /etc/conf/cf.d/unix /stand/unix Etc/conf/bin/idinstall -d adst21 Etc/conf/bin/idinstall -d adst70Troubleshooting Xxxxx011 Error issuing command Adapter was given more or less data than was expected Xxxxx046 Target device did not respond to abort sequence Xxxxx097 Unable to allocate memory Linux Support Linux Operating System World Wide Web URLPage Product Specifications ElectricalPhysical EnvironmentalRegulatory 100 Troubleshooting Troubleshooting ChecklistCommon Error Messages Device connected, but not readyTime-out failure during … Start unit request failed102 Regulatory Information Regulatory Notices Electromagnetic ComplianceFederal Communications Commission Class B EquipmentClass a Equipment Class a Accessories104 For products labeled as Class a For products labeled as Class B105 106 Class a Warning 107 Declaration of Conformity US, EU, Australia 108Warranty and Support Hardware Accessories Limited WarrantyHewlett-Packard Hardware Accessories 109HP Repair and Telephone Support World Wide WebThird-Party Hardware Products CanadaIndex 111112 113 114