Roberts Gorden Linear Heater manual Description Part Number Lower Clearance Shield Package

Page 17

SECTION 7: OPTIONAL HEATER ACCESSORIES

7.4Lower Clearance Shield Installation

Step 7.4.1 Shield Support Strap Assembly

12"

17"(30 cm) (43 cm)

Align Pilot Holes

Locknuts

Washers

Screws

Reflector

Lower Clearance Shield

Description

Part Number

Lower Clearance Shield Package

01397501

 

 

Shield Support Strap

01397500

 

 

Lower Clearance Shield 8' (2.4 m)

02793000

 

 

Locknut #8

92311400

 

 

Flat Washer #8

95310800

 

 

Screw #8 x 3/8''

93511406

 

 

7.5Two-Foot Decorative Grille Installation Step 7.5.1 Grille Installation

Tube and Reflector

 

Hanger

 

Reflector

 

Tube

 

2' x 4' (.6 m x 1.2 m) Aluminum Grille

Suspended Ceiling Frame

 

Description

Part Number

Aluminum Grille 2' x 4' (61 x 122 cm)

91407000

 

31

Image 17
Contents Linear Heater Assembly Overview Linear Heater Layout Overview Description Part Number Burner Tube InstallationCoupling and Tube Assembly Tube Clamp Package InstallationDescription Tube Clamp Package2 Coupling and Tube Assembly 1 Coupling and Tube AssemblyTube Length ModelTurbulator Installation Model Tube Section Turbulator InstallationHanger Burner Tube Reflector Description Part Number Reflector Support Package 1 Reflector, U-Clip and Reflector Support InstallationBurner Installation Optional Heater Accessories Tube Heater Assembly Overview Tube Heater Layout Overview Minimum Distance Required Elbow Package Configuration .2.1 Elbow InstallationBetween Burner and Elbow Elbow Package4 Reflector Joint Installation 2 Elbow Installation3 Reflector Joint Installation Reflector Joint Detail 5 Reflector Joint Detail02712700 Reflector Side Extension 1 Bracket Installation2 Side Reflector Installation Description Part Number Lower Clearance Shield Package Distance a Extension 2 Frame Shield Installation3 Grille Installation 2 Grille End Cap InstallationCanadian Requirements VentingUnited States Requirements Unvented Operation Tube Termination Unvented OperationVertical Venting Vertical Ventilation 4 10 cm Pipe Horizontal Ventilation 4 10 cm PipeTOP View Common Side Wall VentingCommon Vertical Venting Outside Combustion Air Supply Vertical Outside Air Supply for Single Heater InstallationHorizontal Outside Air Supply for Double Heater Installation Vertical Outside Air Supply for Double Heater InstallationGAS Piping Correct Positions Line Voltage Thermostat Wiring WiringFront View Low Voltage Thermostat WiringInternal Wiring Electrical Connection to the Burner Ladder DiagramPre-Season Maintenance and Annual Inspection Operation and MaintenanceSequence of Operation To Shut Off HeaterPlease see Page 49, .5 for suggested items to inspect Vehicles and Other Vicinity of the HeaterObjects ReflectorElectrode Burner Cup and OrificeThermostat Suspension PointsTroubleshooting 12.1 Troubleshooting Flow ChartTroubleshooting Natural Propane Manifold Gas Pressure Setting Top View of HeaterReplacement Parts TOP View Rear ViewDescription Part Number Dimensions General SpecificationsGAS Pressure AT Manifold Pipe ConnectionROBERTS-GORDON LLC will PAY for Warranty is Void ifROBERTS-GORDON LLC will not PAY for Limitations on Authority RepresentativesPage Mail or Fax to Owner Warranty Registration CardPage Page Keep all flammable objects, liquids and vapors the minimum Fire HazardRequired clearances to combustibles away from heater Heater