HP GRACO OR PRO TI1681A manual Fully open the fluid adjustment valve

Page 22

Operation

WARNING

Pressurized Equipment Hazard

To reduce the risk of an injury, follow the Pressure Relief Procedure on page 20 whenever you are instructed to relieve the pressure.

1. Make sure the ES ON/OFF valve is OFF.

I ES O

ti1273a

2. Turn on the main air supply valve (B).

4. Fully open the fan air adjustment valve.

0 KV 100%

μα

HI

LO ES

I ES O

ti1269a

5. Fully open the fluid adjustment valve.

0 KV 100%

μα

HI

LO ES

I ES O

ti1267a

6. Fully open the atomizing air restrictor valve.

3. Position the air cap by loosening the air cap retain- ing ring, and rotating the air cap for a vertical or hor- izontal spray pattern. Tighten the retaining ring until the air cap is held firmly in place; you should not be able to rotate the air cap horns by hand.

ti1272a

Vertical Pattern

7. Make sure the ES ON/OFF valve is OFF.

I ES O

Horizontal Pattern

ti1273a

22

309293J

Image 22
Contents Instructions/Parts List Table of Contents EN 50059 Compliant List of ModelsFM Approved Gun Model DescriptionSymbols Electric Shock HazardFire and Explosion Hazard Toxic Fluid HazardEquipment Misuse Hazard Pressurized Equipment HazardHow the Electrostatic Air Spray Gun Works IntroductionSpraying Waterborne Fluids Electrostatically Gun Overview Gun OverviewSystem Requirements InstallationInstall the System Fire, Explosion, and Electric Shock HazardTypical Installation PRO Xs Waterborne System Key Ground the Cabinet Ventilate the Spray BoothConnect the Air Line Connect the Waterborne Fluid HoseShielded Hose Unshielded HoseWaterborne Hose Dimensions At Graco WB100 Enclosure Unshielded fluid connectionAgitator Kit Agitator KitFluid Regulator Kit Fluid Regulator KitFluid Nozzles Select a Fluid Nozzle and Air CapAir Caps Grounding Check Electrical Grounding Check Gun GroundingOperating Checklist OperationTurn off the main air supply valve B Fill the Fluid Supply Adjust the Spray PatternFire and Explosion Hazard Fully open the fluid adjustment valve Air Regulator Settings Air Hose Length Air Regulator Setting Ft m Psi MPa, barWhen you finish spraying, perform the Shutdown procedure on Low Voltage Adjustment Low Voltage Adjustment Smart Guns OnlyShutdown Maintenance Flush the Spray GunDaily Care and Cleaning Do not immerse the gun in fluidMaintenance Grease Door Latch Threads Clean the Air Cap and Fluid NozzleProcedure Equipment NeededElectrical Tests Test Gun ResistanceTest Power Supply Resistance Test Power Supply ResistanceTest Electrode Resistance ElectrodeTest Ground Strip Resistance Test Cylinder ResistanceSpray Gun TroubleshootingVoltage Loss Troubleshooting Waterborne Fluid HoseVisual Check TestsTroubleshooting Spray Pattern Troubleshooting Gun Operation Troubleshooting Lowing the Fluid Voltage Discharge Grounding Procedure Electrical TroubleshootingSee Test Gun Resistance on See Check Electrical Grounding on 18 and Test Gun ResistancePrepare the Gun for Service RepairAir Cap/Nozzle Replacement Electrode Replacement Electrode ReplacementFluid Packing Removal Fluid Packing RemovalPacking Rod Repair Packing RodBarrel Installation Barrel RemovalPower Supply Removal and Replacement Power SupplyTurbine Alternator Removal and Replacement Fan Air Adjustment Valve Repair Fan Air Adjustment ValveFluid Adjustment Valve Repair Air Valve RepairAtomizing Air Restrictor Valve Removal and Replacement ES ON/OFF Valve RepairParts TI1481a Description Qty Description Qty 51 Ref 19a TI1488A Description Qty SWITCH, ES HI/LO 271 253 276 228 262 NUT Bulkhead Connector 1/4 Tubing and Wiring Chart Code Length Description In. mmDetail of Door Interlock Switch Tubing and Wiring DiagramsDetail of Control Box Air Line Accessories AccessoriesFluid Line Accessories Gun Accessories Miscellaneous AccessoriesPart No Agitator Accessory Kit items 402 407 401 406 403 408 404 406 RefPart No Fluid Regulator Accessory Kit items 506 507 502 505 503Category Technical DataData Graco Information Graco Standard WarrantyToll Free