Toshiba RAV-SP300CT-UL Procedure, Under Ceiling Type, Push simultaneously +, or more

Page 26
Procedure 1

Under Ceiling Type

Installation Manual

Procedure 6

If there is other indoor unit to be changed, repeat procedure 2 to 5 to change the setup.

When the above setup has finished, push Push simultaneously +or more.– 25 –Manual backgroundManual backgroundManual background to select the indoor UNIT No. before change of setup, specify CODE No. [12], [13], [14] in order with temp.

setup Manual background / Manual background buttons, and then check the changed contents.

Address change check Before change: [3-3-1] → After change: [2-2-2]

Pushing Manual background button clears the contents of which setup was changed.

(In this case, procedure from 2 is repeated.)

Indoor UNIT No. before setup change is displayed.

Procedure 7

After check of the changed contents, push Manual backgroundManual background button. (Setup is determined.) When pushing Manual backgroundManual background button, the display disappears and the status becomes the usual stop status. (When pushing Manual backgroundManual background button the operation from the remote control is not accepted for approx.

1 minute.)

*If the operation from the remote control is not accepted even 1 minute or more passed after pushing Manual backgroundManual background button, it is considered that the address setup is incorrect.

In this case, the automatic address must be again set up.

Therefore repeat procedure of the setup change from the Procedure 1.

To recognize the position of the corresponding indoor unit though the indoor UNIT No. is known

Check the position during operation stop. (Be sure to stop operation of the set.)

 

1

1,3

2

Procedure 1

 

Push simultaneously +

buttons for 4 seconds

or more.

 

After a while, the display part flashes and the display appears as shown below.

In this time, the position can be checked because fan and louver of the indoor unit operate.

•For the group control, the indoor UNIT No. is

displayed as [Manual backgroundManual backgroundManual background ] and fans and louvers of all the indoor units in the group control operate.

Check the displayed CODE No. is [01].

•When the CODE No. is other than [01], push Manual backgroundManual background button to erase the display and repeat procedure from the first step.

(After pushing Manual background button, operation of the remote control is not accepted for approx. 1 minute.)

(* Display changes according to the model No. of indoor unit.)

Procedure 2

In the group control, every pushing Manual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background button, the indoor UNIT No. in the group control is displayed in order.

In this time, the position of the indoor unit can be confirmed because only fan of the selected indoor unit operate.

(For a group control, No. of the firstly displayed indoor unit becomes the header unit.)

Procedure 3

After confirmation, push Manual backgroundManual background button to return the mode to the usual mode.

When pushing Manual background button, the display disappears and the status becomes the usual stop status.

(When pushing Manual backgroundManual background button the operation from the remote control is not accepted for approx. 1 minute.)

25-EN

– 25 –

Page 25 Page 27
Image 26
Page 25 Page 27
Contents RAV-SP360CT-UL RAV-SP420CT-UL AIR CONDITIONER SPLIT TYPERAV-SP180CT-UL RAV-SP240CT-UL RAV-SP300CT-UL EnglishContents ADOPTION OF NEW REFRIGERANTUnder Ceiling Type 1 ACCESSORY PARTS„Accessory parts 2 PRECAUTIONS FOR SAFETY Under Ceiling TypeUnder Ceiling Type „Height of ceiling 3 SELECTION OF INSTALLATION PLACE„Installation space Avoid installing in the following places2 Removing wire guard „Wireless remote control„Before installation Under Ceiling TypeInstallation Manual4 Removal of protective vinyl „External view3 Removal of side panel 5 Removal of protectorInstallation Manual Unit in mm Under Ceiling Type„Pipe knockout hole „Installation of hanging bolts„Draw-outdirection of pipe/ wire Using attached installation patternInstallation Manual „Installation of indoor unit„Installation of remote control Sold separately There is ceiling material„Pipe size 4 REFRIGERANT PIPING AND EVACUATING„Refrigerant Piping „Permissible Piping Length and Height DifferenceRefrigerant amount to be added „EvacuationTightening connection Piping with outdoor unitREQUIREMENT Thermal insulation processUnder Ceiling Type „Drain up 5 DRAIN PIPING WORK„Piping/Heat insulating material Under Ceiling Type„Connection of drain pipe „Connection of drain hose„Thermal insulating process Under Ceiling TypeWiring 6 ELECTRICAL CONNECTIONRemote control wiring Under Ceiling TypeUnder Ceiling Type REQUIREMENT „Wire connectionUnder Ceiling Type Under Ceiling Type Connected at backsideConnected at upside 19-EN„Wiring Diagram „System interconnection Wires and Ground Wire„Remote Control Wiring Single systemProcedure „Changing applicable control setting7 APPLICABLE CONTROLS Procedure1 → 2 → 3 → 4 → 5 → „Installation to high ceiling„Using wireless remote control Procedure„Group control „Filter sign setting„To secure better effect of heating Procedure exampleProcedure ProcedureProcedure ProcedureProcedure ProcedureProcedure ProcedureUnder Ceiling Type „Remote control switch monitoring functionInstallation Manual „Before test run 8 TEST RUN2, 4 1,5 „Execute a test runProcedure Wireless remote controlProcedure Procedure„Confirmation and check 9 TROUBLESHOOTING„Confirmation of error history Procedure30-EN „Check codes and parts to be checkedUnder Ceiling Type Under Ceiling Type 31-ENUnder Ceiling Type 32-ENEH99864801
Top Page Image Contents