Toshiba RAV-SP180CT-UL Wireless remote control, Before installation, A p p r o x . 2 3 ’ 7 m

Page 7

Under Ceiling TypeInstallation Manual

Under Ceiling TypeInstallation Manual

Wireless remote control	2 Removing wire guard
Decide the position which remote control is operated	Remove the screws (2 pcs.) which are fixing the
Decide the position which remote control is operated	wire guard.
and the installation place.	Remove the clamp fixing screws and remove the
And then refer to the Installation Manual of the wireless	wire guard.
remote controller kit sold separately.	Clamps
(The signal of the wireless type remote control can be
received within approx. 23’ (7 m). This distance is a
criterion and varies a little according to capacity of the
battery, etc.)
• To prevent malfunction, select a place where is not
affected by a fluorescent lamp or direct sunlight.
• Two or more (up to 6 units) wireless-type indoor units
can be set in a room.

A p p r o x . 2 3 ’ ( 7 m )

Before installation

1 Removal of suction grille

Slide the suction grille fixing knobs (2 positions) toward the arrow direction, and then open the suction grille.

Under the condition of suction grille opened, push the hook section of hinges (2 positions) at the rear side, and then pull out the suction grille.

Suction grille	Suction grille
	fixing knob

Screw

CAUTION

Attach back the wire guard once indoor unit is installed. Remove the 2 screws fixing the wire guard and hung the wire guard with the clamps during a service.

Wire guard

S l i d e

Hinge

Pull out suction grille while pushing hook.

EN

– 6 –

6-EN

Image 7

Contents English AIR CONDITIONER SPLIT TYPERAV-SP180CT-UL RAV-SP240CT-UL RAV-SP300CT-UL RAV-SP360CT-UL RAV-SP420CT-ULADOPTION OF NEW REFRIGERANT Contents„Accessory parts 1 ACCESSORY PARTSUnder Ceiling Type Under Ceiling Type 2 PRECAUTIONS FOR SAFETYUnder Ceiling Type Avoid installing in the following places 3 SELECTION OF INSTALLATION PLACE„Installation space „Height of ceilingUnder Ceiling TypeInstallation Manual „Wireless remote control„Before installation 2 Removing wire guard5 Removal of protector „External view3 Removal of side panel 4 Removal of protective vinylUnder Ceiling Type Installation Manual Unit in mmUsing attached installation pattern „Installation of hanging bolts„Draw-outdirection of pipe/ wire „Pipe knockout holeThere is ceiling material „Installation of indoor unit„Installation of remote control Sold separately Installation Manual„Permissible Piping Length and Height Difference 4 REFRIGERANT PIPING AND EVACUATING„Refrigerant Piping „Pipe sizePiping with outdoor unit „EvacuationTightening connection Refrigerant amount to be addedUnder Ceiling Type Thermal insulation processREQUIREMENT Under Ceiling Type 5 DRAIN PIPING WORK„Piping/Heat insulating material „Drain upUnder Ceiling Type „Connection of drain hose„Thermal insulating process „Connection of drain pipeUnder Ceiling Type 6 ELECTRICAL CONNECTIONRemote control wiring WiringUnder Ceiling Type Under Ceiling Type „Wire connectionREQUIREMENT 19-EN Connected at backsideConnected at upside Under Ceiling TypeSingle system „System interconnection Wires and Ground Wire„Remote Control Wiring „Wiring DiagramProcedure „Changing applicable control setting7 APPLICABLE CONTROLS ProcedureProcedure „Installation to high ceiling„Using wireless remote control 1 → 2 → 3 → 4 → 5 →Procedure example „Filter sign setting„To secure better effect of heating „Group controlProcedure ProcedureProcedure ProcedureProcedure ProcedureProcedure ProcedureInstallation Manual „Remote control switch monitoring functionUnder Ceiling Type „Execute a test run 8 TEST RUN2, 4 1,5 „Before test runProcedure Wireless remote controlProcedure ProcedureProcedure 9 TROUBLESHOOTING„Confirmation of error history „Confirmation and checkUnder Ceiling Type „Check codes and parts to be checked30-EN 31-EN Under Ceiling Type32-EN Under Ceiling TypeEH99864801