HP Workgroup System AWSXCIG-1A manual Interconnect Switch

Page 18

Figure 3-7 Interconnect Switch

The following list describes the callouts in Figure C-1:

1.Port 20 RJ-45 connector for 10/100/1000 Mb uplink

2.Port 21 RJ-45 connector for 10/100/1000 Mb uplink

3.Port 22 RJ-45 connector for 10/100/1000 Mb uplink

4.Port 23 RJ-45 connector for 10/100/1000 Mb uplink

5.Port 24 RJ-45 connector for 10/100/1000 Mb uplink

2.Connect a cable from your laptop to the switch port 21. Callout 2 Figure C-1

3.Verify that no external network is connected to the switch.

4.Use the menus on the Insight Display panel to manually set the static IP address and subnet mask for the OA.

IP address of the OA: 172.31.32.1

IP address of the installation PC: 172.31.32.20

Netmask for the PC: 255.255.0.0

Starting IP address for enclosure bay IP addressing: 172.31.15.1 (this uses the addresses from 172.31.15.1 to 172.31.15.16)

5.On your laptop or PC, manually set a static IP address for the NIC in the same subnet as the IP address you set for the OA.

a.On your PC, go to Start Control Panel Network Connections.

b.Right-clickLocal Area Connection and choose Internet Protocol (TCP/IP).

c.Click Properties and choose Use the Following IP addresses and enter the IP addresses listed below. Remember to reset your laptop after installation if you need to access the corporate network.

6.From your PC or laptop, use the browser to access the OA using the following address: https://172.31.32.1

7.Log in to the OA. Use the default user name Administrator and the default password shown on the tag affixed to the OA.

8.Create a new user name and password. For example, you can make the User name: Root,

and the Password: Test1234 as follows:

a.Click the plus sign (+) to open the User Authentication menu in the left frame.

b.Select the Local Users and click New.

c.Add local user information including a password and confirmation.

d.Change privilege level to Administrator and make sure that the User Enabled is checked.

e.Check Onboard Administrator Bays under User Permissions. Then click the Update User button.

f.Test by signing out of the OA and signing in with the new account information.

9.Assign IP addresses to all iLO2 devices in the enclosure:

a.Click the plus sign (+) to open the Enclosure Settings menu in the left frame.

b.Select the Enclosure Bay IP Addressing menu item.

c.Select the check box to Enable Enclosure Bay IP Addressing.

18 Hardware Setup

Image 18
Contents HP Workgroup System and XC Software Installation Guide Copyright 2008 Hewlett-Packard Development Company, L.P Table of Contents HP Workgroup System Specifications Thermal Stabilization Cabling IP AddressesRemoving the Box List of FiguresEnclosure Bay Numbering Example Rear View OA IP AddressList of Tables List of Examples Modify DatabasePage Document Organization About This DocumentIntended Audience Typographic ConventionsDocumentation Updates and Release Notes HP Encourages Your CommentsUser input HP Workgroup System Overview HP Workgroup System Views3shows an example rear view of the HP Workgroup System Hardware Preinstallation Checklist Hardware PrerequisitesFirmware Requirements Can cause problems HP c-Class BladeSystem Enclosure Components and SwitchesHardware Setup Unpack the EnclosureRemoving the Ramp and Front Cushion Gently roll the unit down the ramp. Callout 1, FigureInstalling and Starting Up the Hardware Plug the unit into a power sourceInterconnect Switch Setting Boot Order Save user informationEnabling Telnet Access Installing and Starting Up the Hardware Page Software Preinstallation Checklist Software PrerequisitesDownloading XC Software Patches Copying the XC.lic File to Your LaptopAssociating the Enclosure DVD to the Head Node Check Choose DVD Connect to the enclosure DVDPage Boot linux ks=hdscd0/ks.cfg XC Software InstallationBooting the DVD Boot linux ks=hdscd0/ks.cfg pci=nommconfRunning the clusterprep Command # cd /opt/hptc/config/sbin# ./clusterprep --enclosurebased # cp /media/iLO2FOLDER/* /home/patches Installing Patches from Your Laptop# mkdir /home/patches # cd /home/patchesRunning the discover Command Putting the License Key File in the Correct Location# cp /media/iLO2-FOLDER/* /opt/hptc/etc/license/XC.lic Running the clusterconfig Command # ./discover --enclosurebased --single --ic=AdminNet# ./clusterconfig Example 5-2 clusterconfig Command Output Ok, Respecify Interfaces O Running the startsys Command Configuring the Snmp TrapLSF Post-Configuration Tasks Verifying LSF-HPC with SlurmFollow along with the OVP command output Running the OVP to Verify Software and Hardware ComponentsVerify the dynamic resource information Nrg Command Nagios Web InterfaceCreating a Baseline Report of the System Configuration Creating a Baseline Copy of the DatabaseSetting Up Vlan Stop bits Flow controlConfirm saving to Flash y/n y Changing External IP Addresses TroubleshootingUnable to Manually Set IP Addresses for the iLOs For example Copy the fileRemoving a Bad Golden Image # sysstart imageandrebootLost Connection to the iLO # siimage baseimageLost Terminal Window When in the IRC Page Additional Software Setup Information # scontrol reconfig# spconfig Page Additional Hardware Setup Information HP Workgroup System SpecificationsTable B-2 Thermal Stabilization Specification IP Addresses IP Addresses on a Corporate NetworkCabling Extend the Insight Display PanelFigure C-3 OA IP Address Configure sendmail Locate the section of the file that is similar to thisConfigure sendmail Glossary Network Base imageItrc NAT SMP Index LSFXC installation, 27 XC license, 24 XC patches