HP Workgroup System AWSXCIG-1A manual Additional Hardware Setup Information

Page 47

B Additional Hardware Setup Information

B.1 HP Workgroup System Specifications

Table B-1 HP Workgroup System Specifications

Size1

Height 54.1 cm (21.20 in)

 

Width 34.24 cm (13.48 in)

 

Depth 87.45 cm (34.43 in)

Weight 2

87.09 kg (192 lb) to 155 kg (342 lb) depending on the

 

configuration

Power Requirements 1

C13/C14 power cords connected directly to low-line wall

 

outlets

Operating Temperature Range3

10°C to 35°C (50°F to 95°F)

Space and Air Flow 4

63.5 cm (25 in) front

 

76.2 cm (30 in) rear

 

121.9 cm (48 in) rear from the rear of another enclosure

 

or rack

1For more details, see HP BladeSystem c3000 Enclosure – Specifications.

2 For more details, see HP BladeSystem c3000 QuickSpecs.

3 For more details, see All product manuals for HP BladeSystem c3000 Enclosures and click HP BladeSystem c3000 Enclosure and c3000 Tower Enclosure Maintenance and Service Guide.

4 For more details, see All product manuals for HP BladeSystem c3000 Enclosures and click HP BladeSystem c3000 Enclosure Setup and Installation Guide.

B.1.1 Thermal Stabilization

Before you remove the enclosure from its packaging, allow it enough time to adjust to the local temperature and humidity of the new operating environment.

CAUTION: Failure to thermally stabilize cluster components can potentially damage drive media or associated electronics when the cluster is activated.

Place the equipment in the room in which it is to be installed. If it arrives in a plastic bag, leave it in the bag. If condensation is visible on any component, stabilize in the operating environment for six hours or until the condensation is no longer visible, whichever is longer. Table B-2specifies the time required to thermally stabilize the enclosure, based on the ambient shipping temperature.

Table B-2 Thermal Stabilization Specification

Ambient Shipping Temperature Range

Ambient Shipping Temperature Range

Minimum Stabilization Time

(°C)

(°F)

 

60 to 66

140 to 151

3 hours

50 to 59

122 to 139

2 hours

40 to 49

104 to 121

1 hour

30 to 39

86 to 103

30 minutes

18 to 29

65 to 85

None

10 to 17

50 to 64

30 minutes

0 to 9

32 to 49

1 hour

-10 to -1

14 to 31

2 hours

-20 to -11

-4 to 13

3 hours

B.1 HP Workgroup System Specifications 47

Image 47
Contents HP Workgroup System and XC Software Installation Guide Copyright 2008 Hewlett-Packard Development Company, L.P Table of Contents Cabling IP Addresses HP Workgroup System Specifications Thermal StabilizationOA IP Address List of FiguresEnclosure Bay Numbering Example Rear View Removing the BoxList of Tables Modify Database List of ExamplesPage Typographic Conventions About This DocumentIntended Audience Document OrganizationUser input Documentation Updates and Release NotesHP Encourages Your Comments HP Workgroup System Views HP Workgroup System Overview3shows an example rear view of the HP Workgroup System Firmware Requirements Hardware Preinstallation ChecklistHardware Prerequisites HP c-Class BladeSystem Enclosure Components and Switches Can cause problemsUnpack the Enclosure Hardware SetupGently roll the unit down the ramp. Callout 1, Figure Removing the Ramp and Front CushionPlug the unit into a power source Installing and Starting Up the HardwareInterconnect Switch Save user information Setting Boot OrderEnabling Telnet Access Installing and Starting Up the Hardware Page Software Prerequisites Software Preinstallation ChecklistCopying the XC.lic File to Your Laptop Downloading XC Software PatchesCheck Choose DVD Connect to the enclosure DVD Associating the Enclosure DVD to the Head NodePage Boot linux ks=hdscd0/ks.cfg pci=nommconf XC Software InstallationBooting the DVD Boot linux ks=hdscd0/ks.cfg# ./clusterprep --enclosurebased Running the clusterprep Command# cd /opt/hptc/config/sbin # cd /home/patches Installing Patches from Your Laptop# mkdir /home/patches # cp /media/iLO2FOLDER/* /home/patches# cp /media/iLO2-FOLDER/* /opt/hptc/etc/license/XC.lic Running the discover CommandPutting the License Key File in the Correct Location # ./clusterconfig Running the clusterconfig Command# ./discover --enclosurebased --single --ic=AdminNet Example 5-2 clusterconfig Command Output Ok, Respecify Interfaces O Configuring the Snmp Trap Running the startsys CommandVerifying LSF-HPC with Slurm LSF Post-Configuration TasksVerify the dynamic resource information Follow along with the OVP command outputRunning the OVP to Verify Software and Hardware Components Nagios Web Interface Nrg CommandCreating a Baseline Copy of the Database Creating a Baseline Report of the System ConfigurationStop bits Flow control Setting Up VlanConfirm saving to Flash y/n y For example Copy the file TroubleshootingUnable to Manually Set IP Addresses for the iLOs Changing External IP Addresses# siimage baseimage # sysstart imageandrebootLost Connection to the iLO Removing a Bad Golden ImageLost Terminal Window When in the IRC Page # spconfig Additional Software Setup Information# scontrol reconfig Page HP Workgroup System Specifications Additional Hardware Setup InformationTable B-2 Thermal Stabilization Specification Extend the Insight Display Panel IP Addresses on a Corporate NetworkCabling IP AddressesFigure C-3 OA IP Address Locate the section of the file that is similar to this Configure sendmailConfigure sendmail Network Base image GlossaryItrc NAT SMP LSF IndexXC installation, 27 XC license, 24 XC patches