HP Workgroup System AWSXCIG-1A manual List of Figures, Enclosure Bay Numbering Example Rear View

Page 5

List of Figures

1-1

Example Front View

11

1-2

Enclosure Bay Numbering

12

1-3

Example Rear View

12

3-1

Opening the Top of the Cardboard Box

15

3-2

Removing the Box

15

3-3

Removing the Ramp and Front Cushion

16

3-4

Attaching the Ramp

16

3-5

Rolling the Unit Down the Ramp

17

3-6

Rolling the Unit to the Installation Location

17

3-7

Interconnect Switch

18

4-1

DVD Drive

25

5-1

IRC Virtual Media Screen

29

C-1

Interconnect Switch

49

C-2

Enclosure Settings Display

49

C-3

OA IP Address

50

5

Image 5
Contents HP Workgroup System and XC Software Installation Guide Copyright 2008 Hewlett-Packard Development Company, L.P Table of Contents Cabling IP Addresses HP Workgroup System Specifications Thermal StabilizationEnclosure Bay Numbering Example Rear View List of FiguresRemoving the Box OA IP AddressList of Tables Modify Database List of ExamplesPage Intended Audience About This DocumentDocument Organization Typographic ConventionsUser input Documentation Updates and Release NotesHP Encourages Your Comments HP Workgroup System Views HP Workgroup System Overview3shows an example rear view of the HP Workgroup System Firmware Requirements Hardware Preinstallation ChecklistHardware Prerequisites HP c-Class BladeSystem Enclosure Components and Switches Can cause problemsUnpack the Enclosure Hardware SetupGently roll the unit down the ramp. Callout 1, Figure Removing the Ramp and Front CushionPlug the unit into a power source Installing and Starting Up the HardwareInterconnect Switch Save user information Setting Boot OrderEnabling Telnet Access Installing and Starting Up the Hardware Page Software Prerequisites Software Preinstallation ChecklistCopying the XC.lic File to Your Laptop Downloading XC Software PatchesCheck Choose DVD Connect to the enclosure DVD Associating the Enclosure DVD to the Head NodePage Booting the DVD XC Software InstallationBoot linux ks=hdscd0/ks.cfg Boot linux ks=hdscd0/ks.cfg pci=nommconf# ./clusterprep --enclosurebased Running the clusterprep Command# cd /opt/hptc/config/sbin # mkdir /home/patches Installing Patches from Your Laptop# cp /media/iLO2FOLDER/* /home/patches # cd /home/patches# cp /media/iLO2-FOLDER/* /opt/hptc/etc/license/XC.lic Running the discover CommandPutting the License Key File in the Correct Location # ./clusterconfig Running the clusterconfig Command# ./discover --enclosurebased --single --ic=AdminNet Example 5-2 clusterconfig Command Output Ok, Respecify Interfaces O Configuring the Snmp Trap Running the startsys CommandVerifying LSF-HPC with Slurm LSF Post-Configuration TasksVerify the dynamic resource information Follow along with the OVP command outputRunning the OVP to Verify Software and Hardware Components Nagios Web Interface Nrg CommandCreating a Baseline Copy of the Database Creating a Baseline Report of the System ConfigurationStop bits Flow control Setting Up VlanConfirm saving to Flash y/n y Unable to Manually Set IP Addresses for the iLOs TroubleshootingChanging External IP Addresses For example Copy the fileLost Connection to the iLO # sysstart imageandrebootRemoving a Bad Golden Image # siimage baseimageLost Terminal Window When in the IRC Page # spconfig Additional Software Setup Information# scontrol reconfig Page HP Workgroup System Specifications Additional Hardware Setup InformationTable B-2 Thermal Stabilization Specification Cabling IP Addresses on a Corporate NetworkIP Addresses Extend the Insight Display PanelFigure C-3 OA IP Address Locate the section of the file that is similar to this Configure sendmailConfigure sendmail Network Base image GlossaryItrc NAT SMP LSF IndexXC installation, 27 XC license, 24 XC patches