HP Workgroup System AWSXCIG-1A About This Document, Intended Audience, Document Organization

Page 9
%, $, or #
audit(5)
Chapter 2
Chapter 3
Chapter 4
Chapter 5
Chapter 6 Appendix A Appendix B
Appendix C
Appendix D

About This Document

This document describes how to set up the hardware and install the XC software on your HP Workgroup System.

IMPORTANT: This document assumes that you are installing the XC Software Version 3.2.1 from a DVD with a valid license key on a new Cluster Platform Workgroup System which consists of a new HP BladeSystem c3000 enclosure that has no external network connection during initial setup and contains the following:

Eight or less factory-installed server blades with current firmware and no operating system installed

A single GbE2c Ethernet switch to which you will connect a Windows laptop to access the Onboard Administrator (OA)

An internal DVD drive

Intended Audience

This document is intended for customers and system administrators experienced in the use of high-performance clusters. Certain operations described in this document, if performed incorrectly, can cause system crashes and loss of data. If you are not familiar with installing and using high-performance clusters, HP recommends that you contact HP Global Services. This document is also intended for HP service representatives and other persons trained to install High-Performance Computing Cluster Platform products. Such persons are expected to understand the hazards of working in this environment and to take suitable precautions to minimize danger to themselves and others.

Document Organization

This document is organized as follows:

Chapter 1 Provides an overview of the HP Workgroup System configuration described in this document, and what you will have when you complete the procedures described in this document.

Provides hardware preinstallation procedures.

Provides hardware setup procedures for unpacking, installing, and starting up. Provides software preinstallation procedures.

Provides software installation procedures for XC System Software. Provides troubleshooting information.

Provides additional software setup information.

Provides additional information about the hardware setup, such as system specifications and thermal stablization.

Provides additional information about how to set up IP addresses on a corporate network..

Provides information about how to configure the LSF sendmail program.

Typographic Conventions

This document uses the following typographical conventions:

A percent sign represents the C shell system prompt. A dollar sign represents the system prompt for the Bourne, Korn, and POSIX shells. A number sign represents the superuser prompt. A manpage. The manpage name is audit, and it is located in Section 5.

Intended Audience

9

Image 9
Contents HP Workgroup System and XC Software Installation Guide Copyright 2008 Hewlett-Packard Development Company, L.P Table of Contents Cabling IP Addresses HP Workgroup System Specifications Thermal StabilizationEnclosure Bay Numbering Example Rear View List of FiguresRemoving the Box OA IP AddressList of Tables Modify Database List of ExamplesPage Intended Audience About This DocumentDocument Organization Typographic ConventionsDocumentation Updates and Release Notes HP Encourages Your CommentsUser input HP Workgroup System Views HP Workgroup System Overview3shows an example rear view of the HP Workgroup System Hardware Preinstallation Checklist Hardware PrerequisitesFirmware Requirements HP c-Class BladeSystem Enclosure Components and Switches Can cause problemsUnpack the Enclosure Hardware SetupGently roll the unit down the ramp. Callout 1, Figure Removing the Ramp and Front CushionPlug the unit into a power source Installing and Starting Up the HardwareInterconnect Switch Save user information Setting Boot OrderEnabling Telnet Access Installing and Starting Up the Hardware Page Software Prerequisites Software Preinstallation ChecklistCopying the XC.lic File to Your Laptop Downloading XC Software PatchesCheck Choose DVD Connect to the enclosure DVD Associating the Enclosure DVD to the Head NodePage Booting the DVD XC Software InstallationBoot linux ks=hdscd0/ks.cfg Boot linux ks=hdscd0/ks.cfg pci=nommconfRunning the clusterprep Command # cd /opt/hptc/config/sbin# ./clusterprep --enclosurebased # mkdir /home/patches Installing Patches from Your Laptop# cp /media/iLO2FOLDER/* /home/patches # cd /home/patchesRunning the discover Command Putting the License Key File in the Correct Location# cp /media/iLO2-FOLDER/* /opt/hptc/etc/license/XC.lic Running the clusterconfig Command # ./discover --enclosurebased --single --ic=AdminNet# ./clusterconfig Example 5-2 clusterconfig Command Output Ok, Respecify Interfaces O Configuring the Snmp Trap Running the startsys CommandVerifying LSF-HPC with Slurm LSF Post-Configuration TasksFollow along with the OVP command output Running the OVP to Verify Software and Hardware ComponentsVerify the dynamic resource information Nagios Web Interface Nrg CommandCreating a Baseline Copy of the Database Creating a Baseline Report of the System ConfigurationStop bits Flow control Setting Up VlanConfirm saving to Flash y/n y Unable to Manually Set IP Addresses for the iLOs TroubleshootingChanging External IP Addresses For example Copy the fileLost Connection to the iLO # sysstart imageandrebootRemoving a Bad Golden Image # siimage baseimageLost Terminal Window When in the IRC Page Additional Software Setup Information # scontrol reconfig# spconfig Page HP Workgroup System Specifications Additional Hardware Setup InformationTable B-2 Thermal Stabilization Specification Cabling IP Addresses on a Corporate NetworkIP Addresses Extend the Insight Display PanelFigure C-3 OA IP Address Locate the section of the file that is similar to this Configure sendmailConfigure sendmail Network Base image GlossaryItrc NAT SMP LSF IndexXC installation, 27 XC license, 24 XC patches