HP Workgroup System AWSXCIG-1A manual Running the startsys Command, Configuring the Snmp Trap

Page 34

The Golden Image will be created next. [P]roceed, [Q]uit: P

CAUTION: Do not interrupt or stop the golden image creation. Do not browse or touch files. Doing so corrupts the golden image.

If you corrupt the golden image, use the following command to remove the base image file (/var/lib/systemimager/images/base_image) to recover from a corrupted golden image:

# si_rmimage base_image

Restart the cluster_config process.

5.7 Running the startsys Command

Use this procedure to start the system and propagate the golden image to all nodes. Ensure that the power is off on all nodes except the head node. The startsys command turns on the power to all nodes, images the nodes, and boots the nodes.

IMPORTANT: You cannot continue if the license file is not present in /opt/hptc/etc/license. For information, see “Putting the License Key File in the Correct Location” (page 30)

IMPORTANT: The startsys command cannot power nodes on or off if the XC password is incorrect because the iLO always prompts for the password. To verify the XC database password, run the following command:

#/opt/hptc/hpls-pwr/mod/getauth

1.Enter the following command:

#setnode --resync --all

2.To image and boot the system in one step, enter the following command:

#startsys --image_and_boot

3.Make sure all the nodes are up. Enter the following command:

#power --status

Troubleshooting file system mounting

You might experience a mount failure when the nodes image, boot, and attempt to NFS mount the /hptc_cluster file system. Run the following commands on the head node to restart nfs and rerun node configuration scripts and restart services on all other nodes:

1.# service nfs restart

2.# pdsh -a touch /var/hptc/nconfig.1st

3.# stopsys

4.# startsys

5.8Configuring the SNMP Trap

To configure the SNMP trap destination for the enclosure, follow these steps:

1.Enter the following command:

#manage_enclosure addtrap

[root@n1 sbin]# manage_enclosure addtrap

n-enc09CN8734016G: Added SNMP trap receiver destination 172.31.15.240 You have new mail in /var/spool/mail/root

[root@n1 sbin]#

34 XC Software Installation

Image 34
Contents HP Workgroup System and XC Software Installation Guide Copyright 2008 Hewlett-Packard Development Company, L.P Table of Contents HP Workgroup System Specifications Thermal Stabilization Cabling IP AddressesRemoving the Box List of FiguresEnclosure Bay Numbering Example Rear View OA IP AddressList of Tables List of Examples Modify DatabasePage Document Organization About This DocumentIntended Audience Typographic ConventionsHP Encourages Your Comments Documentation Updates and Release NotesUser input HP Workgroup System Overview HP Workgroup System Views3shows an example rear view of the HP Workgroup System Hardware Prerequisites Hardware Preinstallation ChecklistFirmware Requirements Can cause problems HP c-Class BladeSystem Enclosure Components and SwitchesHardware Setup Unpack the EnclosureRemoving the Ramp and Front Cushion Gently roll the unit down the ramp. Callout 1, FigureInstalling and Starting Up the Hardware Plug the unit into a power sourceInterconnect Switch Setting Boot Order Save user informationEnabling Telnet Access Installing and Starting Up the Hardware Page Software Preinstallation Checklist Software PrerequisitesDownloading XC Software Patches Copying the XC.lic File to Your LaptopAssociating the Enclosure DVD to the Head Node Check Choose DVD Connect to the enclosure DVDPage Boot linux ks=hdscd0/ks.cfg XC Software InstallationBooting the DVD Boot linux ks=hdscd0/ks.cfg pci=nommconf# cd /opt/hptc/config/sbin Running the clusterprep Command# ./clusterprep --enclosurebased # cp /media/iLO2FOLDER/* /home/patches Installing Patches from Your Laptop# mkdir /home/patches # cd /home/patchesPutting the License Key File in the Correct Location Running the discover Command# cp /media/iLO2-FOLDER/* /opt/hptc/etc/license/XC.lic # ./discover --enclosurebased --single --ic=AdminNet Running the clusterconfig Command# ./clusterconfig Example 5-2 clusterconfig Command Output Ok, Respecify Interfaces O Running the startsys Command Configuring the Snmp TrapLSF Post-Configuration Tasks Verifying LSF-HPC with SlurmRunning the OVP to Verify Software and Hardware Components Follow along with the OVP command outputVerify the dynamic resource information Nrg Command Nagios Web InterfaceCreating a Baseline Report of the System Configuration Creating a Baseline Copy of the DatabaseSetting Up Vlan Stop bits Flow controlConfirm saving to Flash y/n y Changing External IP Addresses TroubleshootingUnable to Manually Set IP Addresses for the iLOs For example Copy the fileRemoving a Bad Golden Image # sysstart imageandrebootLost Connection to the iLO # siimage baseimageLost Terminal Window When in the IRC Page # scontrol reconfig Additional Software Setup Information# spconfig Page Additional Hardware Setup Information HP Workgroup System SpecificationsTable B-2 Thermal Stabilization Specification IP Addresses IP Addresses on a Corporate NetworkCabling Extend the Insight Display PanelFigure C-3 OA IP Address Configure sendmail Locate the section of the file that is similar to thisConfigure sendmail Glossary Network Base imageItrc NAT SMP Index LSFXC installation, 27 XC license, 24 XC patches