HP C6340, C6380, C6350 manual Install the software for a network connection

Page 13

d. Press the down arrow button until Ad Hoc is highlighted, and then press OK. e. Press the down arrow button until Yes, my network uses WEP encryption is

highlighted, and then press OK. The visual keyboard displays.

If you do not want to use WEP encryption, press the down arrow button until No, my network does not use encryption is highlighted, and then press OK. Go to step 7.

6.If prompted, enter your WEP key as follows. Otherwise go to step 7.

a. Use the arrow buttons to highlight a letter or number on the visual keyboard, and then press OK to select it.

NOTE: You must enter the exact uppercase (capital) and lowercase (small) letters. Otherwise, the wireless connection will fail.

b. When you are finished entering the WEP key, use the arrow buttons to highlight Done on the visual keyboard.

7.Press OK again to confirm.

The product will attempt to connect to the SSID. If a message says you entered an invalid WEP key, check the key you wrote down for your new network, follow the prompts to correct the WEP key, and then try again.

8.When the product connects successfully to the network, go to your computer to install the software.

NOTE: You can print the Wireless Network Test report at the end of a successful Wireless Setup Wizard connection which can help identify any potential future issues with the network setup.

Install the software for a network connection

Use this section to install the HP Photosmart software on a computer connected to a network. Before you install the software, make sure you have connected the HP All-in- One to a network.

NOTE: If your computer is configured to connect to a series of network drives, make sure that your computer is currently connected to these drives before installing the software. Otherwise, the HP Photosmart software installer might try to use one of the reserved drive letters and you will not be able to access that network drive on your computer.

NOTE: Installation time can range from 20 to 45 minutes depending on your operating system, the amount of available space, and the processor speed of your computer.

To install the Windows HP Photosmart Software

1.Quit all applications running on your computer, including any virus detection software.

2.Insert the Windows CD that came with the product into the CD-ROM drive on your computer and follow the onscreen instructions.

3.If a dialog box about firewalls appears, follow the instructions. If you see firewall pop- up messages, you must always accept or allow the pop-up messages.

Network setup

Install the software for a network connection

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Basics Guide Hewlett-Packard Company notices Contents Set up the HP All-in-One on a wired Ethernet network Network setupConnect the HP All-in-One to the network What you need for a wired networkTo connect the product to the network Chapter Connect to an integrated wireless Wlan 802.11 network What you need for an integrated wireless Wlan 802.11 networkIf you do not see your network name in the list To connect the product with the Wireless Setup WizardSet up the HP All-in-One using an ad hoc wireless connection To create a network profile What you need for an ad hoc networkCreate a network profile for other operating systems Communication mode ad hoc Encryption enabled Connect to a wireless ad hoc networkTo connect to a wireless ad hoc network To install the Windows HP Photosmart Software Install the software for a network connectionConnect to additional computers on a network To change a USB connection to a wired Ethernet connectionThis runs the Wireless Setup Wizard Configure your firewall to work with HP productsPrint network settings Manage your network settingsAdvanced firewall information Turn the wireless radio on and off Restore network defaultsPrint the wireless network test Wireless Network Test printsHP All-in-One at a glance HP All-in-One overviewLabel Icon Name and Description Control panel featuresStart Here guide Find more informationOnscreen Help HP Web site Load paperTo load full-size paper Chapter Avoid paper jams Print a photo on photo paper Make a copy Scan an imageTo print photos Press Print PhotosTo make a copy from the control panel Replace the ink cartridgesPress Start Copy Black or Start Copy Color to begin copying To replace the ink cartridgesReplace the ink cartridges One overview Troubleshooting common setup issues Uninstall and reinstall the softwareTo uninstall and reinstall the software Setup troubleshooting Solution 1 Press the On button to turn on the product After setting up the product, it does not printSolution 2 Set your product as the default printer Solution 5 Load paper in the input trayWireless Network Test prints Network troubleshootingTo run the Network Diagnostic tool To check a wired Ethernet connectionTo print the Network Configuration Page a. Press Setup To check a wireless connectionMake sure the product is on the network Make sure the product is online and ready To access the HP Photosmart C6300 All-in-One series homeNetwork Status To restart the HP Network Device Support service Make sure the HP Network Devices Support service is runningClear paper jams To check the printer statusInformation on ink cartridges and the printhead If you have a problem, follow these stepsSupport process System requirements Product specificationsRegulatory notices Technical information WarrantyXHPERXUJ UDQDLV
Related manuals
Manual 16 pages 43.7 Kb Manual 331 pages 38.76 Kb
Top Page Image Contents