BENDIX BW2212 manual IR Camera Bracket KIT Piece no Includes, CB Style Mounting KIT Piece no

Page 4

Parts/kits listed are now obsolete and are no longer serviceable through Bendix.

IR CAMERA BRACKET KIT (PIECE NO. 5010078)

INCLUDES:

Mounting Bracket Kit (piece no. 5010187) – The mounting bracket is designed to mount to the vehicle roof (horizontal mounting) or faring area (vertical mounting) and needs to be mounted parallel to the lateral axis of the vehicle (side to side). A template is provided to help guide the drilling of holes. Two stud plates with 1/4-20 studs mount the bracket to the vehicle. The final torque on the studs should be 90-100in-lbs.

Horizontal Mounted Bracket

Vertical Mounted Bracket (Faring

(Roof Mount)

Mount)

FIGURE 2 - MOUNTING BRACKET ORIENTATIONS

The mounting bracket kit also includes shims that should be used to level the mounting bracket. A sealant is to be used between the vehicle, mounting bracket, and stud plate. Verify that the sealant has been applied appropriately, according to the Installation Instructions. Additional mounting hardware is also included in the kit.

Stud Plate

Apply sealant between these surfaces

Add shims if the surface is not level

Roof

IR Camera Bracket with Aiming Adjusters (piece no. 5010673) – One IR camera bracket is provided in the IR camera bracket kit. The bracket includes a standoff base, standoff pivot assembly and aiming adjusters all of which are pre-installed.

Aiming Adjuster Assemblies

Holes for Harness

 

Cable Tie

Standoff and

 

Pivot Assembly

FIGURE 4 - IR CAMERA BRACKET WITH AIMING ADJUSTERS

Cable Tie – A cable tie (to fasten the IR camera harness to the IR camera bracket) is also included in the IR camera bracket kit.

Hardware – The IR camera bracket kit includes all of the necessary hardware to assemble the IR camera, IR camera bracket, and mounting bracket.

CB STYLE MOUNTING KIT (PIECE NO. 5010081)

The CB style mounting kit contains the necessary mounting hardware for the CB style dashboard option and CB style overhead option. When the display is mounted, the combiner surface (and virtual image) must be viewable in the driver’s peripheral vision. A template is provided to help guide the drilling of holes.

The CB style mounting kit includes the following items.

Mounting brackets (piece no. 5009616) – The CB style mounting kit includes two mounting brackets that can be used for either the CB dashboard mount or CB overhead mount.

FIGURE 3 - MOUNTING BRACKET KIT CONTENTS

4

Image 4
Contents SD-19-5160 Table of Contents Introduction Safe Maintenance PracticesComponents IR Camera Bracket KIT Piece no Includes CB Style Mounting KIT Piece noFriction Hinge Mounting KIT Piece no CB Style Dashboard CB Style OverheadHarness KIT Piece no Display Harness CB MountsRED Aiming Adjuster Tool IR CAMERA/ Display CombinationReplacement Kits Power and Ground Power Inputs Electrical SystemServicing the Xvision System Operating Input VoltageIR Camera Bracket Replacement Attach the IR camera harnessIR Camera Attach the IR camera to the IR camera bracketMaintaining Replacing IR CameraReplacing the Aiming Adjusters Aiming Adjuster Replacement KIT ComponentsIR Camera Window ReplacingIR Camera Window Heater Replacement Bezel Heater Assembly and Retaining PlugDisplay Maintaining the Combiner MirrorReplacing the Combiner Mirror Maintaining the Fold MirrorDisplay Bracket Replacement CB Style Mount Dashboard Base Plate 8-32 MountingHarness Replacement Display ReplacementCB Style Mount Dashboard and/or Overhead Friction Hinge Mount VisorHeat Shrinkable Shroud Assembly Vehicle Harness Display HarnessJumper Harness Horizontal Aiming and Adjusting Aiming the IR CameraVertical Aiming and Adjusting Vertical Aiming AdjusterPage Troubleshooting Figures 8 & 9 onSituation Possible Solutions Page