BENDIX BW2212 Display Bracket Replacement CB Style Mount Dashboard, Base Plate 8-32 Mounting

Page 17

Parts/kits listed are now obsolete and are no longer serviceable through Bendix.

Display Bracket Replacement - CB Style Mount (Dashboard)

1.Unscrew and disconnect the 25-pin connector of the display harness.

2.Unscrew the threaded knobs from the display and brackets. Set the display, knobs, and washers aside. Exercise care to prevent dropping the washers into the venting on the dash.

3.Remove the four #10 Plastite® pan head screws from the brackets and dashboard. Set the four screws aside.

4.Secure the replacement brackets with the four screws from Step 3.

5.Torque the screws to approximately 20 in-lbs.

6.Slide one of the washers onto one of the threaded knobs.

7.Hold one washer between the display and a bracket while threading the washer/knob from the outside of the bracket. See Figure 30.

FIGURE 30 - WASHERS AND THREADED KNOBS [SHOWN IN CB STYLE MOUNT (OVERHEAD) POSITION]

8.Repeat steps 6 and 7 for the other side of the display.

9.Reconnect the 25-pin connector of the display harness.

Display Bracket Replacement - CB Style Mount (Overhead)

Refer to CB Style Mount (Dashboard) procedure.

Display Bracket Replacement - Friction Hinge Mount (Visor)

1.Unscrew and disconnect the 25-pin connector of the display harness.

2.Flip the display down to allow access to the friction hinge supports.

3.Remove the four #10 Plastite® pan head screws that secure the display to the headliner.

4.Remove the two M2.5 threadroll pan head screws that secure the friction hinge supports to the display.

5.Secure the new friction hinge supports to the display with the M2.5 threadroll pan head screws.

IMPORTANT: Do not exceed 15 in-lbs. when fastening. If 15 in-lbs. are exceeded, the screw head will shear off or the standoffs will strip. The threadroll screws will form threads in the standoffs as they are tightened. If it feels as though the screw is binding, back out the screw slightly and continue to tighten to prevent breakage.

6.Secure the new friction hinge supports to the headliner with the four #10 Plastite® pan head screws. Torque the screws to approximately 15 in-lbs.

7.Reconnect the 25-pin connector of the display harness.

Base Plate 8-32 Mounting

Four 8-32 inserts are provided in the display base. A template is provided to help guide the drilling of holes. Use a 13/64 in. bit for drilling the four clearance holes. Typically, this installation is used when the display is being recessed.

17

Image 17
Contents SD-19-5160 Table of Contents Components Safe Maintenance PracticesIntroduction CB Style Mounting KIT Piece no IR Camera Bracket KIT Piece no IncludesCB Style Dashboard CB Style Overhead Friction Hinge Mounting KIT Piece noDisplay Harness CB Mounts Harness KIT Piece noRED IR CAMERA/ Display Combination Aiming Adjuster ToolReplacement Kits Electrical System Power and Ground Power InputsServicing the Xvision System Operating Input VoltageAttach the IR camera harness IR Camera Bracket ReplacementAttach the IR camera to the IR camera bracket IR CameraMaintaining Replacing IR CameraAiming Adjuster Replacement KIT Components Replacing the Aiming AdjustersReplacing IR Camera WindowBezel Heater Assembly and Retaining Plug IR Camera Window Heater ReplacementMaintaining the Combiner Mirror DisplayReplacing the Combiner Mirror Maintaining the Fold MirrorBase Plate 8-32 Mounting Display Bracket Replacement CB Style Mount DashboardDisplay Replacement Harness ReplacementCB Style Mount Dashboard and/or Overhead Friction Hinge Mount VisorHeat Shrinkable Shroud Assembly Jumper Harness Display HarnessVehicle Harness Aiming the IR Camera Horizontal Aiming and AdjustingVertical Aiming Adjuster Vertical Aiming and AdjustingPage Figures 8 & 9 on TroubleshootingSituation Possible Solutions Page