Raypak 055B Pressure Switch Adjustment Flame ROLL-OUT Safety Switch, High Limits, TWO Speed Pumps

Page 19

PRESSURE SWITCH ADJUSTMENT:

FLAME ROLL-OUT SAFETY SWITCH

1.With pump and heater on, turn adjustment knob (clockwise) until a click is heard from the gas valve.

2.Turn adjustment knob (counter clockwise) 1/4 turn.

3.Turn pump off and on several times. Heater should shut off immediately. If it does not, repeat steps above until proper adjustment is made.

The heater is equipped with a thermal cutoff device to prevent flame roll-out in the event the heat exchanger becomes blocked. This is a "Single-use" type fusible link or thermal fuse, that must be replaced when dis- abled by an over temperature condition, caused by excessive restriction in the heat exchanger flue pas- sage.

Adjustment Knob

Fig. # 8069.1

Heat Exchanger Height

5' Max.

Fig. #9177

HIGH LIMITS

The heater is equipped with two automatic high limits. Set to operate at 135°F and 140°F.

NOTE: An erratic high limit is often characteristic of internal heat exchanger problem, i.e. scale buildup, U.G. operation. Refer to troubleshooting section.

5' Max.

Pool or Spa

Heat Exchanger Height Fig. # 8152.0s

NOTE: If heater is installed outside of the limits shown, a flow switch must be used in place of the pressure switch when mounted and wired adjacent to the heater.

TWO SPEED PUMPS

In some cases, the flow on the low-speed is insuf- ficient to operate the heater. This is apparent when the pressure switch cannot be further adjusted or if the heater makes banging noises. In these cases, the pump must be run at high speed when heating the water.

CAUTION: Do not operate the heater without the func- tion of a properly adjusted pressure switch.

Fig. # 8159.0s

HIGH LIMIT REMOVAL

1.Disconnect top portion of unit. (See heat ex- change removal procedure step 1 thru 7 and step 10)

2.Remove defective high limit and replace with new high limit.

3.Reverse above procedure to reinstall.

PILOT SAFETY (Millivolt System)

The heaters equipped with the standing pilot (milli- volt system), have pilot generators which act as a safety device to shut off the flow of gas to the main burners and the pilot burner in case the pilot flame is extinguished. The pilot burner must be manually relighted to place the heater in operation again. Refer to the lighting instruc- tions provided on the heater label.

PILOT SAFETY (IID Units) ELECTRIC IGNITION The heater employs a pilot safety which closes the

main gas valve within 8/10ths of a second whenever the pilot flame is interrupted. Pilot flame is automatically lit when the device is powered. Unit performs its own safety check and opens the main valve only after the pilot is proven to be lit.

18

Page 18 Page 20
Image 19
Page 18 Page 20
Contents What to do if YOU Smell GAS VersaContents Water For Your Safety Read Before OperatingSTART-UP Procedures Before START-UP BurnersLighting Instructions Millivolt SystemTo Turn OFF GAS to Appliance Operating Instructions Electronic Ignition SystemsVisual Inspection Maintenance Care ProceduresWater Pressure Switch After START-UPWinterizing the SPA Heater Basic Tips if Heater will not FirePool & SPA Water Chemistry Cold Weather OperationInstallation Instructions General SpecificationReceiving Equipment Outdoor Heaters ALL HeatersVenting Connections Indoor HeatersStep Vent Piping Robertshaw MV GAS Supply ConnectionsModel GAS Pressure RegulatorAutomatic Chlorinators and Chemical Feeders Plumbing for Water Connections LocationFlow Rates Companion Flange ConnectionsElectronic Intermittent Ignition Device System IID Auxiliary Bypass Valve AdjustmentPressure Relief Valve Installation Electrical Wiring Millivolt SystemFig. #9240 Wiring Diagram KEYWiring Diagram Millivolt Units With Solid State Thermostat Wiring Diagram Millivolt Units With Mechanical ThermostatWiring Diagram 152178 Model 055 IID Servicing Instructions CONTROLS/ADJUSTMENTS/REPLACEMENTSTemperature Controls Pressure SwitchHigh Limit Removal Pressure Switch Adjustment Flame ROLL-OUT Safety SwitchHigh Limits TWO Speed PumpsMain Burner and Orifice Removal Pilot Removal and CleaningBurner Drawer Removal GAS Valve RemovalControl Immersion Well Replace Desooting ProcedureUnitherm Governor U.G. Replacement Combustion Chamber RemovalTrouble Shooting Guide Liming Bypassing too much water Measured and Estimated Resistance Match Within 20 Percent Electrical Solid State Thermostat MillivoltElectrical Electronic Ignition IID Troubleshooting Honeywell S8600High Voltage Voltage Between 21.5-28.5 Electrical Solid State Thermostat IIDRAYPAK, INC Agoura Road Westlake VILLAGE, CA Replacement Parts List13-P 14-P 15-P IIDPage Page Warranty Conditions

055B specifications

The Raypak 055B is a high-performance pool and spa heater recognized for its efficiency, reliability, and advanced technologies tailored to meet the needs of consumers. Its compact design and powerful heating capabilities ensure that users enjoy warm water conditions regardless of the outdoor temperature.

One of the main features of the Raypak 055B is its exceptional heating output. With a power rating that can efficiently heat both pools and spas, this model is designed for performance. The heater's efficient heat exchanger is constructed from copper that enhances the transfer of heat, allowing for rapid heating while optimizing energy use. This results in lower utility bills and a smaller environmental footprint.

The Raypak 055B incorporates innovative technology that enhances user experience. It features a digital display that allows for precise temperature control and easy adjustments. Users can set the desired temperature and monitor energy usage, ensuring they achieve the perfect balance between comfort and efficiency. The built-in diagnostic system helps users troubleshoot any issues quickly, maintaining the heater's performance and prolonging its lifespan.

Another significant characteristic of the Raypak 055B is its reliability. The heater is designed with a durable, rust-resistant cabinet that protects the internal components from the elements. This rugged construction makes the Raypak 055B an excellent choice for outdoor installations, ensuring longevity and reliable operation year-round.

The advanced airflow design in the Raypak 055B ensures a safe and efficient operation. The heater is equipped with a standard fan that aids in efficient operation while minimizing noise. Additionally, its low NOx emissions technology meets strict environmental regulations, making it an environmentally friendly option.

The Raypak 055B also includes an innovative ignition system for enhanced safety and convenience. The direct spark ignition eliminates the need for a standing pilot light, reducing gas consumption and further improving efficiency. The unit's freeze protection feature prevents damage during harsh winter conditions, ensuring that users can rely on it throughout the seasons.

In conclusion, the Raypak 055B stands out as a top choice for pool and spa heating solutions. With its combination of efficiency, durability, and advanced technology, it meets the demands of modern consumers looking for comfort without compromising on performance or sustainability. Whether you need to heat a residential pool or a commercial spa, the Raypak 055B is engineered to deliver exceptional results.
Top Page Image Contents