Multiquip MP200DLTE, MP150SDLTS, MP150SDLTE, MP200SDLSM, MP200DLSM Pump Storage, Engine Shut-Down

Page 27

Engine Shut-Down

1.Place speed control lever in the idle position and place the engine start/stop switch in the OFF position.

2.Close vandal cover on engine control box, and lock. Store pad lock key in a safe place, out of the reach of unauthorized persons.

CAUTION - Locking Engine Control Box

When the pump is not in use, close the vandal cover on the engine control box and lock. Locking the engine control box will prevent unauthorized personnel from starting the pump. Store key in a safe place.

CAUTION - Disconnecting Discharge Hose

If pumping in a positive head (pumping up hill), be sure to open discharge check valve drain and release pressure before uncoupling hose.

Pump Inspection After Use

It is recommended that the pump be inspected after use for damage or wear.

1.Drain and flush pump volute and priming system. Usually from suction end.

2.Inspect impeller for wear or damage and measure impeller clearance if it appears worn. Inspect interval should be about every 1000 hours.This inspection should be done when the pump is scheduled for maintenance inspection.

3.Inspect discharge check valve for wear or damage. Replace if necessary.

4.Inspect fuel tank and check for water by removing 0.5-inch drain plugs. Do not overtighten when replacing.

5.Check oil reservoirs for contamination or water.

6.Do dry vacuum test to check seal and check valve seal. This check should be done when the pump is scheduled for maintenance inspection.

OPERATION

Pump Storage

For storage of the pump for over 30 days, the following is required:

zDrain the fuel tank completely.

zRun the engine until the fuel in the injection system is completely consumed.

zCompletely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage.

zRemove the drain plug from the pump and drain out any water from left in the housing.

zRemove the pump cover and clean inside of pump housing. Coat inside of pump housing with a light film of oil to reduce corrosion. A spray can of oil works well for this application.

zCover suction and discharge ports with duct tape to prevent any foreign matter from falling into pump.

zCover pump and engine with plastic covering or equivalent and store in a clean, dry place.

DRY PRIME PUMP — OPERATION AND PARTS MANUAL — REV. #3 (10/06/08) — PAGE 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents DRY Prime Pump Proposition 65WARNING Reporting Safety Defects Reporting Safety DefectsTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Table of Contents DRY Prime Pump Operation and Parts Manual REV. #3 10/06/08 For Your Safety and the Safety of Others Safety Message Alert SymbolsAlways wear approved respiratory protection Safety Message Alert SymbolsOperating the pump Rules for Safe OperationAdd 1000 lbs kg. to Rules for Safe OperationBattery Pump Dimensions Pump DimensionsTrailer Dimensions Trailer DimensionsPump Specifications SpecificationsSpecifications Engine Impeller General InformationRear Fuel Tank Drain Plugs Remove either plug to drain fuel Pump ComponentsPump Components Type alternator Engine. See for detailed specificationsEngine Components SolenoidEngine Hour Meter Displays the number of hours Voltmeter Gauge Indicates the battery chargeEngine has been in use Oil Pressure Meter Monitors engine oil pressurePump Application Pumping ApplicationTowing Application See Trailer Safety GuidelinesSetup Suction and discharge hoses arePump will not be able to begin Tighten fuel tank cap securely after filling InspectionOperation To the Start positionLonger suction hoses will require Engine Shut-Down Pump StorageMaintenance Pump Engine MaintenanceDry Pump Vacuum Test Maintenance Engine Imsa Fuel Filter Fuel Water Separator FilterFuel Tank Surge Brakes Maintenance TrailerManually Adjusting the Brakes Trailer BrakesHydraulic Brack Actuator Breakaway BatteryBreakaway Switch Brakes must be synchronizedWheel Bearings Hubs Adjustable ChannelWheel Hub Adjustment „ Install a new cotter pin through the spindle nut and axleTorsion Suspension Trailer MaintenanceAlways use lower gears for climbing and descending grades Trailer Safety GuidelinesCommon Causes for Loss of Trailer Trailer Towing GuidelinesCoupling to the Tow Vehicle Trailer Safety GuidelinesNever drive faster than what is safe Driving ConditionsInoperable Brakes, Lights or Mirrors Reporting Safety DefectsAdministrator New Jersey Avenue S.E Washington, DCVehicle VIN Tag Trailer VIN TagSuspension System Electrical ConnectorSafety Chains Tow VehicleBefore coupling the tow vehicle to CouplerTypes„ Ball Hitch Coupler „ Pintle Eye Coupler Ball Hitch CouplerOverloading can damage More than 1 inch Breakaway Cable Surge Brake System Attaching Safety Chain„ Attach the safety chains so that they Breakaway Brake SystemElectric BrakeTesting Connecting Trailer LightsUncoupling the Ball Hitch Pintle Coupler and Pintle Hook Pintle Hitch CouplerTire Safety Unsafe Tires, Lug Nuts or WheelsImproper tire pressure causes an unstable trailer and can Tire and Loading Information Determining Load Limit of TrailerStep Determining Load Limit of Tow Vehicle StepTire Fundamentals P indicates the tire is for passenger vehicles Uniform Tire Quality Grading Standards UtqgsReplacing Worn or Damaged Tires Tire Safety TipsLoad Range Tire RepairStart all wheel lug nuts by hand Wheel RimsWheels, Bearings and Lug Nuts Lug Nut Torque RequirementsLights and Signals Trailer Lightswiring DiagramTire and Loading Information Nameplate and DecalsPriming or Pump Flow Problems Troubleshooting PumpEngine Troubleshooting Troubleshooting EngineDipstick Troubleshooting EngineSurge Brake Troubleshooting Troubleshooting Trailer BrakesDRY Prime Pump Operation and Parts Manual REV. #3 10/06/08 Your Local Dealer is HERE’S HOW to GET Help

MP200SDLTE, P200DLST, MP150SDLSM, MP200DLTS, MP200DLSM specifications

The Multiquip MP series of vibratory plate compactors, including models MP200DLTS, MP200DLTE, MP150SDLTE, P200DLST, and MP200SDLTE, are engineered for exceptional performance in compaction tasks across a variety of applications. These models are vital for contractors seeking efficiency, power, and reliability in the field.

The MP200DLTS and MP200DLTE models are particularly noteworthy for their robust design and versatility. Both are equipped with a powerful engine that delivers high centrifugal force, allowing operators to achieve effective compaction on different soil types. Their durable construction ensures longevity, even in demanding environments. The MP200DLTS features a dual-direction capability for increased maneuverability, while the MP200DLTE is designed for heavier-duty tasks and larger areas.

For users looking for a slightly more compact solution, the MP150SDLTE is a standout choice. This model combines portability with power, making it ideal for smaller jobs or confined spaces. It excels in providing precise compaction where larger equipment may struggle, while still maintaining high performance standards.

The P200DLST model offers enhanced features such as a heavy-duty baseplate designed to offer increased stability and excellent surface contact. This contributes to better results when compacting asphalt or granular materials, making it a preferred choice for road construction and repair projects.

Finally, the MP200SDLTE boasts advanced technology that enriches its operational capabilities. With an integrated vibration control system, users can adjust the compaction force on the fly, allowing for tailored performance based on specific job requirements. Its ergonomic handle design enhances user comfort, reducing fatigue during extended use.

Safety is also a priority in these models, with features such as protective guards and emergency stop buttons, ensuring that operators can work confidently. The overall combination of power, versatility, and innovative features makes the Multiquip MP series an essential tool for contractors in both construction and landscaping sectors.

In summary, whether it’s the heavy-duty capabilities of the MP200 series or the compact efficiency of the MP150SDLTE, Multiquip's offerings deliver outstanding performance, making them ideal for various compaction tasks. The robust engineering and thoughtful features provide users with the reliability needed in today’s competitive marketplace.
Top Page Image Contents