Pelco DD53TC16-X manual Regulatory Notices, Radio and Television Interference

Page 39

REGULATORY NOTICES

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

REVISION HISTORY

Manual #

Date

Comments

 

C2446M

2/02

Original version.

 

C2446M-A

4/02

Software revised.

 

C2446M-B

11/02

Revised Quick Start Guide.

 

C2446M-C

2/03

Manual revised to include features of software version 1.2.

 

C2446M-D

1/04

Added alert feature. Updated menus and instructions.

 

C2446M-E

11/05

Made manual changes for Spectra III software version 1.28 per ECO 05-11592. Added information to access

 

 

preset 95 from the WS5050 and VCD5000.

 

® Pelco, the Pelco logo, and Genex are registered trademarks of Pelco.

© Copyright 2005, Pelco.

™ Spectra III and LowLight are trademarks of Pelco.

All rights reserved.

C2446M-E (11/05)

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Spectra III Series Page 16X LowLight Color Technology C2446M-E 11/05 Contents Regulatory Notices Pelco Spectra Version Address Comm 2400, N, 8 Configure DoneWelcome Getting StartedHOW to Operate Your Dome System CM6700/CM6800 Accessing Main Menu PresetNET300/NET350/NET4001A Preset Function Following presets are reserved for special functionsC2446M-E 11/05 Language Quick Programming GuideSee System Information Display Setup Label Position Camera Dome SettingsNumeric Value Advanced Camera SettingsShutter Speed AGC LimitAuto Iris Auto Iris LevelAuto Iris Peak Auto Sharpness Auto White BalanceGain Backlight Compensation BLC Video LevelNormal Proportional PAN Motion SettingsThere are two auto flip modes On default Auto FlipPark Action None default No actionPreset Park TimeScan Scan SpeedLimit Stops ManualAzimuth Zero Power UP Action Power UpDome synchronizes to an internal clock Line SyncDetermined zero reference point PresetsFollowing presets are predefined for specific functions Preset ActionPatterns To edit a zone label ZonesTitle Text Alert RepeatSystem Condition Alert Message Current Reading Reset AlertACK Action Activate AUXClear Password Reboot System RESET, Cycle POWER, RebootReset Camera Cycle Camera PowerUpload Icon SOFTWARE/LANGUAGE File UploadSpecifications NtscPAL Radio and Television Interference Regulatory NoticesPage Page ISO9001
Related manuals
Manual 42 pages 59.32 Kb
Top Page Image Contents