ContentsPageCool Summer Offer
Features of your new air conditionerCost Efficient System
Look for EverywhereUSING PARTS
Safety precautionsImportant safety symbols and precautions
FOR INSTALLATIONFOR POWER SUPPLY
FOR USINGDo not pull the power cord, when unplugging the power plug
Do not touch the power plug or the circuit breaker with wet handsDo not clean the inside of the air conditioner by yourself
FOR CLEANINGDo not place objects or devices under the indoor unit
Do not operate the appliance with wet handsOperation ranges
Checking before useModel RJ
Maintaining your air conditionerChecking the name of the parts
Power buttonMain parts
DisplayRemote controller buttons
Checking the remote controllerRemote controller display Smart Saver
On TimerBattery changing time
Remote controller displayStoring the remote controller
Turbo indicatorAuto
Basic functionCool
HeatPress the button to turn on the air conditioner
button to adjust the temperaturePress the button to set the operating mode
Press theUsing the Turbo function
Adjusting the air flow directionPress the Air swingbutton on the remote controller
Press the Turbo button on the remote controller during Cool mode1. Press the button on the remote controller
When the air conditioner is on and in cool/heat modemode
Temperature and fan speed changes in modeSetting On timer Setting Off timer
Setting the On/Off timer1. Press the On Timer/Off Timer button
Additional options available in On timer modeIf the air conditioner is on
Using the Smart Saver functionIf the air conditioner is off
Combining On Timer and Off TimerUsing the Auto Clean function
Using the Quiet functionPress the Auto Clean button When the air conditioner is turned off
When the air conditioner is turned onCleaning the indoor unit
Cleaning the air conditionerCleaning the outdoor unit heat exchanger
Opening the panelRemoving the Air filter
Cleaning the air filterOpen the panel and put the Air filter out
Dry the Air filter in a ventilated areaPeriodical checks
Maintaining the air conditionerPROBLEM
TroubleshootingSOLUTION
not work at allNoise is generated
Error is indicatedflow movement changes. It is normal
the outdoor unitGeneral information
INSTALLATION PARTSIncluded ModelsInstalling the unit
Choosing the installation locationPower supply line, fuse or circuit breaker
Indoor unitOutdoor UnitWhen installing more than 1 outdoor unit
When installing 1 outdoor unitSpace Requirements for Outdoor Unit
Top viewAccessories in the indoor unit case
AccessoriesAccessories in the outdoor unit caseOptional accessories
Fixing the installation plateTools required for installation General Tools
Tools for test operationsCable specification
Connecting the assembly cableConnecting the cable
Power cableof the electrical contact during a wiring work10. Connect the grounding conductor to the grounding terminals
Installing and connecting the assembly pipe of the indoor unit11. Close the terminal board cover by tightening the screw carefully
2. Smooth the cut edgesCutting or extending the pipe
Purging the indoor unit4. Cut off the remaining foam insulation
6. Pass the pipe through the hole in the wallDepth A
4. Put a flare nut slightly into the pipe and modify the flareOuter Diameter
Outer Diameter DDrain hose installation
Installing and connecting the drain hose of the indoor unitChanging direction of the drain hose
Installing and connecting the drain hose of the indoor unit1. Detach the rubber cap with the plier
2. Detach the drain hose by pulling it and turning to the leftPurging the connected pipes
InstallAA ing and connecting the drain hose of the outdoor unit2. Connect a drain hose to the drain plug
3. Ensure that condensation draining is adequateAdding Refrigerant
gas service port as seen in the pictureIf you use a pipe longer than 5m
If you use a pipe shorter than 5mCylinder with siphon
Important information regulation regarding the refrigerant used1. Please fill in with indelible ink
1975To check for gas leaks on the outdoor unit
PerfoAA rming the gas leak testsTo check for gas leaks on the indoor unit
Leak test with nitrogen before opening valves6. Attach the pipe to the wall using clamps optional
Outdoor unit installed on the wall by rackFixinAA g the indoor unit in place
Fixing the outdoor unit in place4. Press the Power button to stop the operation
1. Press the Power button and check the followingFinalAA Check and Trial Operation
Check the followingsand compress another two points in the same location
The compression dimension should be5. Apply heat to the contraction tube to contract it
6. After tube contraction work is completed, wrap it with the1. Turn the power off and take off the front panel of the indoor unit
Sub PCB installationoptional2. Take off the Cover PCB
3. Attach the Sub PCB to the right side of the Panel-frameENGLISHCOUNTRY
QUESTIONS OR COMMENTS?CALL
EEE Yönetmeliğine Uygundur This EEE is compliant with RoHSAir Conditioner
user & installation manualimagine the possibilities
AQV07P Series AQV09P Series AQV12P Series AQV18P Series