Samsung AQV09PWAX Checking the name of the parts, Main parts, Display, Power button, English

Page 7

Checking the name of the parts

Your air conditioner may slightly look different from illustration shown above depending on your model.

Main parts

Air filter(under the panel)

Air flow blade (up and down)

Blade pin lever

Room temperature sensor

Air intake

Air flow blade (left and right)

ENGLISH

Display

indicator

Timer/Auto clean indicator

Operation indicator

Power button

Remote controller receiver

Image 7

Contents Page Look for Everywhere Features of your new air conditionerCool Summer Offer Cost Efficient SystemFOR INSTALLATION Safety precautionsUSING PARTS Important safety symbols and precautionsDo not touch the power plug or the circuit breaker with wet hands FOR USINGFOR POWER SUPPLY Do not pull the power cord, when unplugging the power plugDo not operate the appliance with wet hands FOR CLEANINGDo not clean the inside of the air conditioner by yourself Do not place objects or devices under the indoor unitMaintaining your air conditioner Checking before useOperation ranges Model RJDisplay Power buttonChecking the name of the parts Main partsOn Timer Checking the remote controllerRemote controller buttons Remote controller display Smart SaverTurbo indicator Remote controller displayBattery changing time Storing the remote controllerHeat Basic functionAuto CoolPress the button to adjust the temperaturePress the button to turn on the air conditioner Press the button to set the operating modePress the Turbo button on the remote controller during Cool mode Adjusting the air flow directionUsing the Turbo function Press the Air swingbutton on the remote controllerTemperature and fan speed changes in mode When the air conditioner is on and in cool/heat mode1. Press the button on the remote controller modeAdditional options available in On timer mode Setting the On/Off timerSetting On timer Setting Off timer 1. Press the On Timer/Off Timer buttonCombining On Timer and Off Timer Using the Smart Saver functionIf the air conditioner is on If the air conditioner is offWhen the air conditioner is turned on Using the Quiet functionUsing the Auto Clean function Press the Auto Clean button When the air conditioner is turned offOpening the panel Cleaning the air conditionerCleaning the indoor unit Cleaning the outdoor unit heat exchangerDry the Air filter in a ventilated area Cleaning the air filterRemoving the Air filter Open the panel and put the Air filter outPeriodical checks Maintaining the air conditionernot work at all TroubleshootingPROBLEM SOLUTIONthe outdoor unit Error is indicatedNoise is generated flow movement changes. It is normalGeneral information INSTALLATION PARTSIncluded Models Indoor unit Choosing the installation locationInstalling the unit Power supply line, fuse or circuit breakerOutdoor Unit Top view When installing 1 outdoor unitWhen installing more than 1 outdoor unit Space Requirements for Outdoor UnitAccessories in the indoor unit case AccessoriesAccessories in the outdoor unit case Tools for test operations Fixing the installation plateOptional accessories Tools required for installation General ToolsPower cable Connecting the assembly cableCable specification Connecting the cableof the electrical contact during a wiring work 2. Smooth the cut edges Installing and connecting the assembly pipe of the indoor unit10. Connect the grounding conductor to the grounding terminals 11. Close the terminal board cover by tightening the screw carefully6. Pass the pipe through the hole in the wall Purging the indoor unitCutting or extending the pipe 4. Cut off the remaining foam insulationOuter Diameter D 4. Put a flare nut slightly into the pipe and modify the flareDepth A Outer DiameterDrain hose installation Installing and connecting the drain hose of the indoor unit2. Detach the drain hose by pulling it and turning to the left Installing and connecting the drain hose of the indoor unitChanging direction of the drain hose 1. Detach the rubber cap with the plier3. Ensure that condensation draining is adequate InstallAA ing and connecting the drain hose of the outdoor unitPurging the connected pipes 2. Connect a drain hose to the drain plugIf you use a pipe shorter than 5m gas service port as seen in the pictureAdding Refrigerant If you use a pipe longer than 5m1975 Important information regulation regarding the refrigerant usedCylinder with siphon 1. Please fill in with indelible inkLeak test with nitrogen before opening valves PerfoAA rming the gas leak testsTo check for gas leaks on the outdoor unit To check for gas leaks on the indoor unitFixing the outdoor unit in place Outdoor unit installed on the wall by rack6. Attach the pipe to the wall using clamps optional FixinAA g the indoor unit in placeCheck the followings 1. Press the Power button and check the following4. Press the Power button to stop the operation FinalAA Check and Trial Operation6. After tube contraction work is completed, wrap it with the The compression dimension should beand compress another two points in the same location 5. Apply heat to the contraction tube to contract it3. Attach the Sub PCB to the right side of the Panel-frame Sub PCB installationoptional1. Turn the power off and take off the front panel of the indoor unit 2. Take off the Cover PCBENGLISH EEE Yönetmeliğine Uygundur This EEE is compliant with RoHS QUESTIONS OR COMMENTS?COUNTRY CALLAQV07P Series AQV09P Series AQV12P Series AQV18P Series user & installation manualAir Conditioner imagine the possibilities

Related manuals

Manual 41 pages 25.73 Kb

Manual 41 pages 25.56 Kb

Manual 41 pages 6.72 Kb

Manual 45 pages 23.92 Kb

Manual 41 pages 27.43 Kb

Manual 43 pages 36.93 Kb

Manual 43 pages 57.93 Kb

Manual 41 pages 20.41 Kb

Manual 21 pages 39.04 Kb

Manual 21 pages 44.89 Kb

Manual 21 pages 49.66 Kb