Samsung AF28FSSDADFNMG, AF28FSSDAWKNFA manual Installing the earth wire, Charging refrigerant

Page 53

Installing the earth wire

Earthing must be done by the installation specialist for your safety. ffConnect grounding electrode and the air conditioner.

Charging refrigerant

1.Connect the manifold gauge in the low pressure side (gas) and press Set/Cancel, Mode, Temp + button simultaneously for 5 seconds to enter the refrigerant charging mode. When the outdoor unit operates, charge the refrigerant.

2.Charge the refrigerant depending on the pipe length.

-- If the installed pipe length exceeds standard length (5m), you must add 30g of refrigerant (R-410A) for every 1m. -- You do not need to charge the additional refrigerant when pipe length is less than 5m.

Manifold gauge

Gas side

 

Liquid side

Refrigerant

 

Electronic scale

3.After charging the refrigerant, disconnect the manifold gauge from the service port and close the service cap.

4.Deactivate the refrigerant charging mode by pressing Set/Cancel, Mode, Temp + button simultaneously for 5 seconds.

• Make sure to charge refrigerant with accurate amount by using the electronic scale.

CAUTION

52

칠레향 FAC MEMORY 냉난방_IBIM_EN_03892A(5).indd 52

2014-03-12 오전 9:33:18

Image 53
Contents This product is RoHS compliant Questions or COMMENTS?Thank you for purchasing this Samsung product Air ConditionerSeasons of effective cleaning Features of your new air conditionerSmart sensor Applicable to Affssd onlyContents Important safety symbols and precautions Safety precautionsInjury or death Injury or property damageFfThis may result in electric shock or fire For Power Supply Warning For Using FfThis may result in electric shock or burns Do not drink the water from the air conditioner Do not place objects or devices under the indoor unitDo not operate the appliance with wet hands Do not clean the inside of the air conditioner by yourself For CleaningUse extra heating apparatus during heat mode Cool mode, set the appropriate desired temperatureChecking before use Make sure that curtain does not block the air inletAuxiliary power switch NFB, ELB, etc Auxiliary power switchOperation ranges Functions available for each modelHeating capacity Discharge cool air Checking the name of the partsIndoor unit Number of air outlets is different depending on the models DisplayButtons on control panel Operation with control panel Stop Press the PowerFan speed of each air outlet will differ Button one more timeRemote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasic operation Press the button to adjust the desired temperature Press the button to set the operation modePress the button to turn on the air conditioner Solomode RemarksTurbo operation Press Button on the remote controller in the Cool/Heat modeAir flow direction Press the button to select desired air flow directionGoodsleep operation When the air conditioner is on and in cool modeTemperature and fan speed changes in goodsleep mode Goodsleep functions Setting the On/Off timerAdditional options available in On timer mode Air conditioner will turn on after 3 hours Preset time on On timer is longer than Off timerYour air conditioner will turn on To adjust the lighting level of an indoor unit Press the button during Cool modeSmart sensor operation Lighting functionQuiet operation Auto clean operationCleaning the indoor unit Cleaning the air conditionerCleaning the outdoor unit heat exchanger Be careful with the sharp edges on the outdoor unitRemove dust with a vacuum cleaner or running water Cleaning the Full HD filterFull HD Filter filters the big dust of incoming air Pull out the Full HD filter in the arrow directionDry the filter in a ventilated area Cleaning the Zero filterFfDo not disassemble the Zero filter when cleaning it Troubleshooting Clean the Zero filter and Full HD Filter if they are dirty Controller after setting the timeSpeed Check if your batteries are depletedContact a service center Error is indicatedConditioner, push the Zero filter to the end Not worry about fire with thisOpen Source Announcement Installation parts Safety precautions Required tools Choosing the installation locationGeneral tools Tools for test operationsPiping length for indoor/outdoor unit installation Indoor/outdoor unit installation diagramInstallation space for floor type indoor unit Outdoor unit Fixing outdoor unitTo make sure water is drained properly Connecting the outdoor unit drain hoseIndoor unit accessories AccessoriesOutdoor unit accessories Installation accessoriesInstallation procedure Connecting pipesDrilling a hole and fixing the indoor unit FfDrill a hole with diameter of 60~65mm towards the outsideFfIncorrectly flared pipes FfFlare processFfFlare length FfPipe insulation FfTightening of connection partsIndoor Use finishing tape wind up the refrigerant pipe DiameterDFix the drain hose tightly to prevent any water leakage Connecting drain hoseConnection with wire-concealed piping Connecting procedure Wiring standardIndoor power Indoor/outdoor unit power cable Electrical workType of outdoor unit power supply Safety information on outdoor unit power supplyTorque Kgfcm 25~40FfItems to prepare How to connect your extended power cablesApply heat to the contraction tube to contract it FfVacuuming air conditioner Vacuum pumpVacuuming pipe Test part for indoor unit Performing leak testNm = 10 kgfcm Outer Tightening torqueCharge the refrigerant depending on the pipe length Installing the earth wireCharging refrigerant Disconnect the pipe Check and test operation
Related manuals
Manual 56 pages 43.72 Kb Manual 64 pages 24.82 Kb