Quadra-Fire 810-03201, CASTINS-CSB, 810-02901, CASTINS-CWL owner manual Igniter Replacement

Page 36

R

Castile Pellet Insert

E. Igniter Replacement

Igniter Bracket

Thumb Screw

Igniter

Figure 36.1

a.Shut down the appliance by turning down the thermostat and let the appliance completely cool down. After the appliance has cooled down, unplug it and remove the ash pan.

b.The wire leads to the igniter are connected to the wire harness with 1/4 inch (6mm) male / female spade connectors. These wires will pull forward approximately 4 to 5 inches (102 to 127mm). Disconnect the spade connections and remove the igniter from the chamber. Loosen the thumb screw and slide igniter out.

c.Install new igniter into the chamber and tighten the thumb screw. Re-connect the wires to the 2 leads with the spade connectors.

d.Remove the right cast side and pull the wire leads back toward the rear of the appliance to take-up the 4 to 5 inches (102mm to 107mm) previously pulled out. This will keep the wires out of the way of the ash pan. Double check that the igniter wires are clear of any movement, i.e. ash pan, fi repot cleaning rod, cleaning slide plates, etc.

f.Re-install the ash pan and then re-install the cast side panel and re-connect the power.

F. Glass Replacement

WARNING

•Glass is 5mm thick high temperature heat- resistant ceramic glass.

•DO NOT REPLACE with any other material.

•Alternate material may shatter and cause injury

a.Open hinged cast face and lift door assembly off from the insert and lay on a fl at surface face down.

b.Using a screwdriver, tap the bottom of the rope retainer rod to push it up out of the hole. The top end of the rod will slide up. Swing the rod toward you from the bottom and remove the rod. Repeat for other side.

c.Remove old glass and replace with new glass.

d.Slide the retainer rod into the top hole fi rst, and then line up the bottom crimped end with the hole in the door. The crimped end must be paralle with the glass in order to insert it into place. Figure 36.2.

Rope Retainer

Rods

Slide this

end in first

Glass

Crimped end

at the bottom

Crimped end must be

parallel with the glass

Figure 36.2

Page 36

250-7251G

August 20, 2009

Page 35 Page 37
Image 36
Page 35 Page 37
Contents 810-02901 MBK 810-03201 PMH Hot glass will cause burnsCastile Pellet Insert Insurance carrier, localBuilding inspector, fi re Inspection and permitsTable of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency Specifi cationsMobile Home Approved Glass Specifi cationsGetting Started Appliance LocationCastile Pellet Insert Locating Your Appliance & Chimney DraftNegative Pressure Castile Pellet Insert Fire Safety Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance DimensionsHeight Width Panel Size Inch Castile Pellet Insert Clearance To Combustibles, UL and ULC 0mm Clearance To Exposed Section And Face TrimShown Optional Outside Air Inches MillimetersCastile Pellet Insert Masonry and Zero Clearance Fireplaces Floor ProtectionMinimum Opening for Masonry and Zero Clearance Fireplaces Location Inches MillimetersStarter hole Mark area of floor to cut Castile Pellet Insert Prefabricated Metal Chimney Altering the Factory-Built Fireplace4Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart Castile Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems Full Reline With Outside Air HorizontalCastile Pellet Insert Full Reline With Outside Air Vertical Mobile Home Installation 6Mobile HomeTop Vent Installation Rear Vent Installation7Appliance Set-Up Reversible Top or Rear Flue Adapter Leveling SystemAssembled View DescriptionBase Plate Only Installation Castile Pellet Insert Zero Clearance Trim Support Cont’d20.3 Panel Set And Cast Trim Set Panel & Trim Set, Econo21.3 Four Piece Log Set Installation Castile Pellet Insert Thermostat Installation 8Operating Instructions Fuel Size, Material and StorageFire Characteristics Castile Pellet Insert General Operating InformationBefore Your First Fire Starting Your First FireCastile Pellet Insert Feed Rate Adjustment Iginition CyclesFrequently Asked Questions Issues SolutionsTroubleshooting SymptomSymptom Possible Cause Corrective Action Page Quick Reference Maintenance Chart 10Maintaining & Servicing Your ApplianceTypes of Fuel Frequency Daily Weekly Monthly YearlyRemove Cast Sides for Cleaning & Maintenance Cleaning Firepot with Cleaning Rod & Firepot ScraperNished. See .2 on Ash Removal from FireboxCleaning Ash Pan Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning the Exhaust PathCleaning the Hopper Cleaning Convection Blower Requires No LubricationCleaning Exhaust Blower Requires No Lubrication Door Latch Inspection Cleaning the GlassHigh Ash Fuel Content Maintenance Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly Igniter Replacement Baffl e & Brick Set Removal 37.1Re-installing Baffl e & Brick Set Cont’d Component Function Vacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FCastile Pellet Insert Component Locations Blowers & Feed MotorCastile Pellet Insert Exploded Drawing 250-7251G August 20Castile Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to OrderStocked At DepotDescription Comments Part Number TOUCHUP-CSB Description ACCESSORIESComments Part Number PEL-DAMP4Description Comments Part Number Stocked at Depot FastenersCastile Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Warranty Policy Castile Pellet Insert Contact Information

CASTINS-CSB, 810-03201, 810-02901, CASTINS-CWL specifications

The Quadra-Fire 810-02901 and 810-03201, commonly referred to by their model designations CASTINS-CSB and CASTINS-CWL, represent a significant advancement in wood burning technology. These stoves are designed for efficiency, ease of use, and aesthetic appeal, catering to the increasing demand for sustainable and effective home heating solutions.

One of the standout features of these models is their high-efficiency combustion system. The technology employed in the Quadra-Fire 810 series optimizes fuel usage, ensuring that wood burns more completely. This not only maximizes heat output but also minimizes emissions, making it a more environmentally-friendly heating option compared to traditional wood stoves. By utilizing advanced combustion technology, these stoves can achieve higher efficiency ratings, which is essential for reducing heating costs and maintaining a comfortable indoor climate.

Both models come with a substantial firebox capacity, allowing users to load a significant amount of wood. This design feature ensures longer burn times and less frequent reloading, providing convenience for homeowners. The large viewing window creates an inviting ambiance and allows for a clear view of the mesmerizing flames, making these stoves a focal point in any living space.

The CASTINS-CSB model is particularly notable for its robust construction, featuring high-quality cast iron that provides excellent heat retention. This material not only contributes to durability but also enhances the overall thermal performance of the stove. The CASTINS-CWL model also incorporates a striking design with clean lines and a modern aesthetic, making it suitable for both traditional and contemporary home décor.

In terms of safety features, both models are equipped with advanced air control systems that facilitate easy adjustment of combustion airflow. This ensures safe operation and allows users to maintain optimal temperatures. The stoves are also designed to integrate with existing ventilation systems, promoting efficient airflow throughout the home.

Overall, the Quadra-Fire 810-02901 (CASTINS-CSB) and 810-03201 (CASTINS-CWL) models embody state-of-the-art wood burning technology with an emphasis on efficiency, quality, and design. These stoves are an ideal choice for homeowners looking to embrace a sustainable heating method without compromising on style or substance.
Top Page Image Contents