Quadra-Fire 810-03201, CASTINS-CSB, 810-02901 Castile Pellet Insert Prefabricated Metal Chimney

Page 12
August 20, 2009
250-2061
250-2061

R

Castile Pellet Insert

G. Prefabricated Metal Chimney

The chimney can be new or existing, masonry or prefabricated and must meet the following minimum requirements:

•Must be minimum 6 inch (152mm) inside diameter of high temperature chimney listed to UL 103 HT (2100oF) or ULC-S628.

•Must use components required by the manufacturer for installation.

•Must maintain clearances required by the manufacturer for installation.

•Refer to manufacturers instructions for installation

•This insert is listed to UL 1482 Standard and is approved for installation into listed factory-built zero clearance fi re- places listed to UL 127 conforming to the following speci- fi cations and instructions:

•The original factory-built clearance fi replace chimney cap must be re-installed after installing the approved chimney liner meeting type UL 103 HT requirements (2100°F) per UL 1777.

•If the chimney is not listed as meeting HT requirements, or if the factory built fi replace was tested prior to 1998, a full height listed chimney liner must be installed from the appliance fl ue collar to the chimney top.

•The liner must be securely attached to the insert fl ue collar and the chimney top.

•The air fl ow of the factory-built zero-clearance fi replace system must not be altered. The fl ue liner top support attachment must not reduce the air fl ow for the existing air-cooled chimney system.

•No dilution air is allowed to enter the chimney.

1.Secure the fi replace damper in the open position. If this cannot be accomplished, it will be necessary to remove the damper

2.Seal damper area of chimney around chimney connector with a high temperature sealant or seal insert against the face of the fi replace.

3.Both methods must be removable and replaceable for cleaning and re-installation.

H. Altering the Factory-Built Fireplace

•The fireplace must not be altered, except for the exceptions listed below. Do not removal the bricks and mortar from the existing fi replace.

The following modifi cations are premissible:

•Removal of damper or locked in open position

•Removal of smoke shelf or baffl e

•Removal of ember catches

•Removel of fi re grate

•Removal of view screen/curtain

•Removal of doors

•External trim pieces which do not affect the operation of the fireplace may be removed providing they can be stored on or within the fi replace for reassembly if the insert is removed.

•The permanent metal warning label provided must be attached to the back of the fi replace, with screws or nails, stating that the fi replace may have been altered to accommodate the insert, and must be returned to original condition for use as a conventional fi replace. Figure 11.1

•If the hearth extension is lower than the fi replace opening, the portion of the insert extending onto the hearth must be supported.

•Manufacturer designed adjustable support kit can be ordered from your dealer.

•Final approval of this installation type is contingent upon the authority having jurisdiction.

NOTE: Refer to chimney liner manufacturer for recom- mendations on supporting the liner. Installation into fi replaces without a permit will void the listing

WARNING! Risk of Fire!

Follow venting manufacturer’s clearances and instructions when installing venting system.

NOTICE: In Canada when using a factory-built chim- ney it must be safety listed, Type UL103 HT (2100oF) [1149oC] CLASS “A” or conforming to CAN/ULC-

S629M, STANDARD FOR 650oC FACTORY-BUILT CHIMNEYS.

WARNING

THIS FIREPLACE MAY HAVE BEEN ALTERED TO ACCOMMODATE AN INSERT. IT MUST BE RETURNED TO ITS ORIGINAL CONDITION BEFORE USE AS A SOLID FUEL BURNING FIREPLACE.

Figure 121

Page 12

250-7251G

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 810-02901 MBK 810-03201 PMH Hot glass will cause burnsCastile Pellet Insert Insurance carrier, localBuilding inspector, fi re Inspection and permitsTable of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency Specifi cationsMobile Home Approved Glass Specifi cationsGetting Started Appliance LocationCastile Pellet Insert Locating Your Appliance & Chimney DraftNegative Pressure Castile Pellet Insert Fire Safety Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance DimensionsHeight Width Panel Size Inch Castile Pellet Insert Clearance To Combustibles, UL and ULC 0mm Clearance To Exposed Section And Face TrimShown Optional Outside Air Inches MillimetersCastile Pellet Insert Masonry and Zero Clearance Fireplaces Floor ProtectionMinimum Opening for Masonry and Zero Clearance Fireplaces Location Inches MillimetersStarter hole Mark area of floor to cut Castile Pellet Insert Prefabricated Metal Chimney Altering the Factory-Built Fireplace4Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart Castile Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems Full Reline With Outside Air HorizontalCastile Pellet Insert Full Reline With Outside Air Vertical Mobile Home Installation 6Mobile HomeTop Vent Installation Rear Vent Installation7Appliance Set-Up Reversible Top or Rear Flue Adapter Leveling SystemAssembled View DescriptionBase Plate Only Installation Castile Pellet Insert Zero Clearance Trim Support Cont’d20.3 Panel Set And Cast Trim Set Panel & Trim Set, Econo21.3 Four Piece Log Set Installation Castile Pellet Insert Thermostat Installation 8Operating Instructions Fuel Size, Material and StorageFire Characteristics Castile Pellet Insert General Operating InformationBefore Your First Fire Starting Your First FireCastile Pellet Insert Feed Rate Adjustment Iginition CyclesFrequently Asked Questions Issues SolutionsTroubleshooting SymptomSymptom Possible Cause Corrective Action Page Quick Reference Maintenance Chart 10Maintaining & Servicing Your ApplianceTypes of Fuel Frequency Daily Weekly Monthly YearlyRemove Cast Sides for Cleaning & Maintenance Cleaning Firepot with Cleaning Rod & Firepot ScraperNished. See .2 on Ash Removal from FireboxCleaning Ash Pan Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning the Exhaust PathCleaning the Hopper Cleaning Convection Blower Requires No LubricationCleaning Exhaust Blower Requires No Lubrication Door Latch Inspection Cleaning the GlassHigh Ash Fuel Content Maintenance Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly Igniter Replacement Baffl e & Brick Set Removal 37.1Re-installing Baffl e & Brick Set Cont’d Component Function Vacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FCastile Pellet Insert Component Locations Blowers & Feed MotorCastile Pellet Insert Exploded Drawing 250-7251G August 20Castile Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to OrderStocked At DepotDescription Comments Part Number TOUCHUP-CSB Description ACCESSORIESComments Part Number PEL-DAMP4Description Comments Part Number Stocked at Depot FastenersCastile Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Warranty Policy Castile Pellet Insert Contact Information

CASTINS-CSB, 810-03201, 810-02901, CASTINS-CWL specifications

The Quadra-Fire 810-02901 and 810-03201, commonly referred to by their model designations CASTINS-CSB and CASTINS-CWL, represent a significant advancement in wood burning technology. These stoves are designed for efficiency, ease of use, and aesthetic appeal, catering to the increasing demand for sustainable and effective home heating solutions.

One of the standout features of these models is their high-efficiency combustion system. The technology employed in the Quadra-Fire 810 series optimizes fuel usage, ensuring that wood burns more completely. This not only maximizes heat output but also minimizes emissions, making it a more environmentally-friendly heating option compared to traditional wood stoves. By utilizing advanced combustion technology, these stoves can achieve higher efficiency ratings, which is essential for reducing heating costs and maintaining a comfortable indoor climate.

Both models come with a substantial firebox capacity, allowing users to load a significant amount of wood. This design feature ensures longer burn times and less frequent reloading, providing convenience for homeowners. The large viewing window creates an inviting ambiance and allows for a clear view of the mesmerizing flames, making these stoves a focal point in any living space.

The CASTINS-CSB model is particularly notable for its robust construction, featuring high-quality cast iron that provides excellent heat retention. This material not only contributes to durability but also enhances the overall thermal performance of the stove. The CASTINS-CWL model also incorporates a striking design with clean lines and a modern aesthetic, making it suitable for both traditional and contemporary home décor.

In terms of safety features, both models are equipped with advanced air control systems that facilitate easy adjustment of combustion airflow. This ensures safe operation and allows users to maintain optimal temperatures. The stoves are also designed to integrate with existing ventilation systems, promoting efficient airflow throughout the home.

Overall, the Quadra-Fire 810-02901 (CASTINS-CSB) and 810-03201 (CASTINS-CWL) models embody state-of-the-art wood burning technology with an emphasis on efficiency, quality, and design. These stoves are an ideal choice for homeowners looking to embrace a sustainable heating method without compromising on style or substance.
Top Page Image Contents