Quadra-Fire 810-02901 Cleaning the Hopper, Cleaning Convection Blower Requires No Lubrication

Page 34

R

Castile Pellet Insert

10.Cleaning the Hopper

•Frequency: Monthly or after burning 1 ton of fuel

•By: Homeowner

After burning approximately 1 ton of fuel you will need to clean the hopper to prevent sawdust build-up.

A combination of sawdust and pellets on the auger reduces the amount of fuel supply to the fi repot. This can result in nuisance shutdowns and mis-starts.

a.The appliance must be in complete shutdown. Allow the appliance to completely cool down.

b.Empty the hopper of any remaining pellets.

CAUTION

Handle glass assembly with care.

When cleaning glass:

• Avoid striking, scratching or slamming glass.

• Do NOT clean glass when hot.

•Do NOT use abrasive cleaners.

•Use a hard water deposit glass cleaner on white fi lm.

•Refer to maintenance instructions.

c.Vacuum the hopper and feed tube.

11.Soot and Fly Ash: Formation & Need for Removal in Exhaust Venting System.

•Frequency: Yearly or more frequently depending on ash build-up.

•By: Qualifi ed Service Technician/Homeowner

Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off.

The products of combustion will contain small particles of fl y ash. The fl y ash will collect in the exhaust venting system and restrict the fl ow of the fl ue gases.

At start-up if there is incomplete combustion, or if there is a shutdown or incorrect operation of the appliance it will lead to some soot formation. This will collect in the exhaust vent- ing system.

The venting system may need to be cleaned at least once a year or more often depending upon the quality of your fuel or if there is a lot of horizontal pipe sections. Ash will build up more quickly in the horizontal sections.

13.Cleaning Convection Blower - Requires No Lubrication

•Frequency: Yearly or as needed

•By: Qualifi ed Service Technician

a.The appliance must be in complete shutdown and completely cooled.

b.Remove both the left and right cast sides.

c.Use either a can of compressed air or an air com- pressor.

d.Reach as far back as possible and spray com- presssed air liberally from both sides at the blower. This will remove any lint or dust build-up on the impellers.

14.Cleaning Exhaust Blower - Requires No Lubrication

•Frequency: Yearly or as needed

•By: Qualifi ed Service Technician

•Task: Contact your local dealer.

15.Door Latch Inspection

12.Cleaning the Glass

•Frequency: When clear view of the fi repot becomes obscure

•By: Homeowner

a.Appliance must be completely cool before cleaning glass.

b.Use a damp paper towel or any non-abrasive glass cleaner. Wipe off with dry towel.

•Frequency: Prior to heating season

•By: Homeowner

The door latch is non-adjustable but the gasketing between the glass and fi rebox should be inspected periodically to make sure there is a good seal.

NOTE: There is no gasket on the bottom of glass.

WARNING

Handle glass with care.

• Inspect the gasket to ensure it is undamaged.

• Do NOT strike, slam or scratch glass.

• Do NOT operate appliance with glass assembly removed.

•Do NOT operate with glass cracked, broken or scratched.

Page 34

250-7251G

August 20, 2009

Page 33 Page 35
Image 34
Page 33 Page 35
Contents 810-02901 MBK 810-03201 PMH Hot glass will cause burnsBuilding inspector, fi re Castile Pellet InsertInsurance carrier, local Inspection and permitsTable of Contents Mobile Home Approved Listing and Code ApprovalsAppliance Certification BTU & Efficiency Specifi cations Glass Specifi cationsGetting Started Appliance LocationDraft Castile Pellet Insert Locating Your Appliance & ChimneyNegative Pressure Tools And Supplies Needed Castile Pellet Insert Fire SafetyInspect Appliance & Components and Pre-Use Check List Appliance Dimensions 3Dimensions and ClearancesHeight Width Panel Size Inch Shown Optional Outside Air Castile Pellet Insert Clearance To Combustibles, UL and ULC0mm Clearance To Exposed Section And Face Trim Inches MillimetersMinimum Opening for Masonry and Zero Clearance Fireplaces Castile Pellet Insert Masonry and Zero Clearance FireplacesFloor Protection Location Inches MillimetersStarter hole Mark area of floor to cut Castile Pellet Insert Prefabricated Metal Chimney Altering the Factory-Built FireplaceChimney and Exhaust Connection 4Vent InformationVenting Termination Requirements Castile Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems Full Reline With Outside Air HorizontalCastile Pellet Insert Full Reline With Outside Air Vertical Mobile Home Installation 6Mobile Home7Appliance Set-Up Top Vent InstallationRear Vent Installation Reversible Top or Rear Flue Adapter Leveling SystemAssembled View DescriptionCastile Pellet Insert Zero Clearance Trim Support Cont’d Base Plate Only Installation20.3 Panel & Trim Set, Econo Panel Set And Cast Trim Set21.3 Four Piece Log Set Installation Castile Pellet Insert Thermostat Installation 8Operating Instructions Fuel Size, Material and StorageBefore Your First Fire Fire CharacteristicsCastile Pellet Insert General Operating Information Starting Your First FireCastile Pellet Insert Feed Rate Adjustment Iginition CyclesFrequently Asked Questions Issues SolutionsTroubleshooting SymptomSymptom Possible Cause Corrective Action Page Types of Fuel Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance Frequency Daily Weekly Monthly YearlyNished. See .2 on Remove Cast Sides for Cleaning & MaintenanceCleaning Firepot with Cleaning Rod & Firepot Scraper Ash Removal from FireboxCleaning Beneath Heat Exchanger Cleaning Ash PanCleaning Heat Exchanger Chambers & Drop Tube Cleaning the Exhaust PathCleaning Exhaust Blower Requires No Lubrication Cleaning the HopperCleaning Convection Blower Requires No Lubrication Door Latch Inspection Cleaning the GlassDoor Gasket Inspection High Ash Fuel Content MaintenancePreparing Firebox for Non-Burn Season Frequency Yearly Igniter Replacement Baffl e & Brick Set Removal 37.1Re-installing Baffl e & Brick Set Cont’d Component Function Snap Disc #1 Convection Blower 110F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Fuel Delivery Interrupt 250FCastile Pellet Insert Component Locations Blowers & Feed MotorCastile Pellet Insert Exploded Drawing 250-7251G August 20Castile Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to OrderAt Depot StockedDescription Comments Part Number TOUCHUP-CSB Description ACCESSORIESComments Part Number PEL-DAMP4Description Comments Part Number Stocked at Depot FastenersCastile Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Warranty Policy Castile Pellet Insert Contact Information

CASTINS-CSB, 810-03201, 810-02901, CASTINS-CWL specifications

The Quadra-Fire 810-02901 and 810-03201, commonly referred to by their model designations CASTINS-CSB and CASTINS-CWL, represent a significant advancement in wood burning technology. These stoves are designed for efficiency, ease of use, and aesthetic appeal, catering to the increasing demand for sustainable and effective home heating solutions.

One of the standout features of these models is their high-efficiency combustion system. The technology employed in the Quadra-Fire 810 series optimizes fuel usage, ensuring that wood burns more completely. This not only maximizes heat output but also minimizes emissions, making it a more environmentally-friendly heating option compared to traditional wood stoves. By utilizing advanced combustion technology, these stoves can achieve higher efficiency ratings, which is essential for reducing heating costs and maintaining a comfortable indoor climate.

Both models come with a substantial firebox capacity, allowing users to load a significant amount of wood. This design feature ensures longer burn times and less frequent reloading, providing convenience for homeowners. The large viewing window creates an inviting ambiance and allows for a clear view of the mesmerizing flames, making these stoves a focal point in any living space.

The CASTINS-CSB model is particularly notable for its robust construction, featuring high-quality cast iron that provides excellent heat retention. This material not only contributes to durability but also enhances the overall thermal performance of the stove. The CASTINS-CWL model also incorporates a striking design with clean lines and a modern aesthetic, making it suitable for both traditional and contemporary home décor.

In terms of safety features, both models are equipped with advanced air control systems that facilitate easy adjustment of combustion airflow. This ensures safe operation and allows users to maintain optimal temperatures. The stoves are also designed to integrate with existing ventilation systems, promoting efficient airflow throughout the home.

Overall, the Quadra-Fire 810-02901 (CASTINS-CSB) and 810-03201 (CASTINS-CWL) models embody state-of-the-art wood burning technology with an emphasis on efficiency, quality, and design. These stoves are an ideal choice for homeowners looking to embrace a sustainable heating method without compromising on style or substance.
Top Page Image Contents