Quadra-Fire 810-02901, 810-03201 Castile Pellet Insert Locating Your Appliance & Chimney, Draft

Page 6

R

Castile Pellet Insert

B. Locating Your Appliance & Chimney

Location of the appliance and chimney will affect performance.

•Install through the warm airspace enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-down of the fi re.

•Penetrate the highest part of the roof. This minimizes the effects of wind loading.

•Locate termination cap away from trees, adjacent structures, uneven roof lines and other obstructions.

•Minimize the use of chimney offsets.

•Consider the appliance location relative to fl oor and ceiling and attic joists.

CAUTION

•DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE.

•DO NOT CONNECT TO ANY AIR DISTRIBUTON DUCT OR SYSTEM.

C. Draft

Draft is the pressure difference needed to vent appliances successfully. When an appliance is drafting successfully, all combustion byproducts are exiting the home through the chimney.

Considerations for successful draft include:

•Preventing negative pressure

•Location of appliance and chimney

NOTICE: Hearth & Home Technologies assumes no responsibility for the improper performance of the chimney system caused by:

•Inadequate draft due to environmental conditions

•Downdrafts

•Tight sealing construction of the structure

•Mechanical exhausting devices

D. Negative Pressure

WARNING! Risk of Asphyxiation! Negative pressure can

cause spillage of combustion fumes and soot.

Negative pressure results from the imbalance of air avail- able for the appliance to operate properly. It can be stron- gest in lower levels of the house.

Causes include:

•Exhaust fans (kitchen, bath, etc.)

•Range hoods

•Combustion air requirements for furnaces, water heaters and other combustion appliances

•Clothes dryers

•Location of return-air vents to furnace or air conditioning

•Imbalances of the HVAC air handling system

•Upper level air leaks such as:

-Recessed lighting

-Attic hatch

-Duct leaks

To minimize the effects of negative air pressure:

•Install the outside air kit with the intake facing prevailing winds during the heating season

•Ensure adequate outdoor air for all combustion appliances and exhaust equipment

•Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the appliance

•Avoid installing the appliance near doors, walkways or small isolated spaces

•Recessed lighting should be a “sealed can” design

•Attic hatches weather stripped or sealed

•Attic mounted duct work and air handler joints and seams taped or sealed

Page 6

250-7251G

August 20, 2009

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 810-02901 MBK 810-03201 PMH Hot glass will cause burnsBuilding inspector, fi re Castile Pellet InsertInsurance carrier, local Inspection and permitsTable of Contents Mobile Home Approved Listing and Code ApprovalsAppliance Certification BTU & Efficiency Specifi cations Glass Specifi cationsGetting Started Appliance LocationCastile Pellet Insert Locating Your Appliance & Chimney DraftNegative Pressure Castile Pellet Insert Fire Safety Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance DimensionsHeight Width Panel Size Inch Shown Optional Outside Air Castile Pellet Insert Clearance To Combustibles, UL and ULC0mm Clearance To Exposed Section And Face Trim Inches MillimetersMinimum Opening for Masonry and Zero Clearance Fireplaces Castile Pellet Insert Masonry and Zero Clearance FireplacesFloor Protection Location Inches MillimetersStarter hole Mark area of floor to cut Castile Pellet Insert Prefabricated Metal Chimney Altering the Factory-Built Fireplace4Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart Castile Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems Full Reline With Outside Air HorizontalCastile Pellet Insert Full Reline With Outside Air Vertical Mobile Home Installation 6Mobile Home7Appliance Set-Up Top Vent InstallationRear Vent Installation Reversible Top or Rear Flue Adapter Leveling SystemAssembled View DescriptionBase Plate Only Installation Castile Pellet Insert Zero Clearance Trim Support Cont’d20.3 Panel Set And Cast Trim Set Panel & Trim Set, Econo21.3 Four Piece Log Set Installation Castile Pellet Insert Thermostat Installation 8Operating Instructions Fuel Size, Material and StorageBefore Your First Fire Fire CharacteristicsCastile Pellet Insert General Operating Information Starting Your First FireCastile Pellet Insert Feed Rate Adjustment Iginition CyclesFrequently Asked Questions Issues SolutionsTroubleshooting SymptomSymptom Possible Cause Corrective Action Page Types of Fuel Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance Frequency Daily Weekly Monthly YearlyNished. See .2 on Remove Cast Sides for Cleaning & MaintenanceCleaning Firepot with Cleaning Rod & Firepot Scraper Ash Removal from FireboxCleaning Beneath Heat Exchanger Cleaning Ash PanCleaning Heat Exchanger Chambers & Drop Tube Cleaning the Exhaust PathCleaning Exhaust Blower Requires No Lubrication Cleaning the HopperCleaning Convection Blower Requires No Lubrication Door Latch Inspection Cleaning the GlassHigh Ash Fuel Content Maintenance Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly Igniter Replacement Baffl e & Brick Set Removal 37.1Re-installing Baffl e & Brick Set Cont’d Component Function Snap Disc #1 Convection Blower 110F Vacuum SwitchWiring Harness See .1 below Snap Disc #2 Fuel Delivery Interrupt 250FCastile Pellet Insert Component Locations Blowers & Feed MotorCastile Pellet Insert Exploded Drawing 250-7251G August 20Castile Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to OrderStocked At DepotDescription Comments Part Number TOUCHUP-CSB Description ACCESSORIESComments Part Number PEL-DAMP4Description Comments Part Number Stocked at Depot FastenersCastile Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCastile Pellet Insert Service And Maintenance Log Cont’d Castile Pellet Insert Warranty Policy Castile Pellet Insert Contact Information

CASTINS-CSB, 810-03201, 810-02901, CASTINS-CWL specifications

The Quadra-Fire 810-02901 and 810-03201, commonly referred to by their model designations CASTINS-CSB and CASTINS-CWL, represent a significant advancement in wood burning technology. These stoves are designed for efficiency, ease of use, and aesthetic appeal, catering to the increasing demand for sustainable and effective home heating solutions.

One of the standout features of these models is their high-efficiency combustion system. The technology employed in the Quadra-Fire 810 series optimizes fuel usage, ensuring that wood burns more completely. This not only maximizes heat output but also minimizes emissions, making it a more environmentally-friendly heating option compared to traditional wood stoves. By utilizing advanced combustion technology, these stoves can achieve higher efficiency ratings, which is essential for reducing heating costs and maintaining a comfortable indoor climate.

Both models come with a substantial firebox capacity, allowing users to load a significant amount of wood. This design feature ensures longer burn times and less frequent reloading, providing convenience for homeowners. The large viewing window creates an inviting ambiance and allows for a clear view of the mesmerizing flames, making these stoves a focal point in any living space.

The CASTINS-CSB model is particularly notable for its robust construction, featuring high-quality cast iron that provides excellent heat retention. This material not only contributes to durability but also enhances the overall thermal performance of the stove. The CASTINS-CWL model also incorporates a striking design with clean lines and a modern aesthetic, making it suitable for both traditional and contemporary home décor.

In terms of safety features, both models are equipped with advanced air control systems that facilitate easy adjustment of combustion airflow. This ensures safe operation and allows users to maintain optimal temperatures. The stoves are also designed to integrate with existing ventilation systems, promoting efficient airflow throughout the home.

Overall, the Quadra-Fire 810-02901 (CASTINS-CSB) and 810-03201 (CASTINS-CWL) models embody state-of-the-art wood burning technology with an emphasis on efficiency, quality, and design. These stoves are an ideal choice for homeowners looking to embrace a sustainable heating method without compromising on style or substance.
Top Page Image Contents