Napoleon Fireplaces NPS40 INSTALLATION, Minimum Clearance To Combustibles, Corner Installation

Page 15

NPS40 INSTALLATION

MINIMUM CLEARANCE TO COMBUSTIBLES

STRAIGHT INSTALLATION

Through the Wall Installations

Interior Vertical Vents

Figure 10

Figure 9

CORNER INSTALLATION

Through the Wall Vents

Interior Vertical Vents

Figure 11

Figure 12

NOTE: If interior vertical pellet vent is used, the clearance to the back wall is determined by the upward-turning elbow or "Tee". It will vary in depth depending on the brand of pellet vent used (it is approximately 5"). Before placing the heater, connect the elbow or "Tee" and allow for the minimum 3" clearance to the combustible wall.

W415-0616 / C / 06.04.08

Image 15

Contents W415-0616 /C $10.00W415-0616 /C PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE TABLE of CONTENTSCONDITIONS AND LIMITATIONS WARRANTYW415-0616 /C WARNINGS AND SAFETY PRECAUTIONSW415-0616 /C WARNINGS AND SAFETY PRECAUTIONSPELLET QUALITY SPECIFICATIONS HEATING SPECIFICATIONSGENERAL INTRODUCTION GENERAL INSTRUCTIONSDIMENSIONS Figures 1a-bFigures 2a-c Figures 3a-c DIMENSIONS CONTINUEDDIMENSIONS CONTINUED Figures 4a-cNPI40 with AK8 Adapter and GICSK Flashing Shown HEATER PLACEMENT GENERAL INSTALLATIONSPECIFICATIONS PLANNING YOUR INSTALLATIONOUTSIDE AIR INSTALLATION OPTIONSSAFETY FEATURES FLOOR PROTECTION REQUIREMENTSTYPE OF VENT INSTALLING THE PELLET VENTGENERAL VENTING MOBILE HOMEMinimum Alcove Dimensions ALCOVE INSTALLATION NPS40 ONLYVENTING THE PELLET HEATER PELLET VENT TERMINATIONJ D ABBFI LG H E MINIMUM AIR TERMINAL INSTALLATIONSMINIMUM CLEARANCE TO COMBUSTIBLES NPS40 INSTALLATIONSTRAIGHT INSTALLATION CORNER INSTALLATIONTHROUGH WALL WITH VERTICAL RISE AND HORIZONTAL VENTING INSTALLATION EXAMPLESHORIZONTAL EXHAUST THROUGH WALL INSTALLATION TERMINATION INSTALLATIONCLASS A CHIMNEY RETROFIT MINIMUM INSIDE VERTICAL CLEARANCESRecommended HEARTH MOUNT INSTALLATIONPRIOR TO INSTALLATION INSTALLATIONINTOAMASONRYFIREPLACEREAR TO TOP VENT CONVERSION INSTRUCTIONS NPI40 INSTALLATIONMINIMUM CLEARANCES TO COMBUSTIBLES MINIMUM MANTEL CLEARANCESNPI40 INSTALLATION OVERVIEW PRIOR TO INSTALLATION INSTALLATION INTO A MASONRY FIREPLACEHORIZONTAL VENT INSTALLATION VERTICAL LINER INSTALLATIONINSTALLATION INTO A MASONRY FIREPLACE INSTALLATION INTO A FACTORY BUILT METAL FIREPLACELINER INSTALLATION PRIOR TO INSTALLATIONFigure 24b INSTALLATION INTO A COMBUSTIBLE BUILT-INENCLOSUREMINIMUM FRAMING DIMENSIONS Figure 24aFLASHING INSTALLATION NPI40 FINISHINGMINIMUM ENCLOSURE CLEARANCES PROPER PELLET LOADING INSTALL VIEWING DOOR NPS40 AND NPI40TRIVET NPI40 LIGHTING HEATER MANUALLYOPERATING INSTRUCTIONS START-UPSHUT-DOWN OPEN MAIN VIEWING DOOR GENERAL MAINTENANCE NPS40 AND NPI40DAILY WHENEVER USING THE HEATER CLEANING GLASS DOORMAKE SURE PELLETS ARE NOT PILING UP CLEANING THE HEAT EXCHANGE TUBESCLEANING THE BURN POT BI-WEEKLYOR EVERY 10 BAGS OF PELLETSVACUUM FIREBOX SEMI-ANNUALLYOR EVERY TWO TONS OF PELLET VACUUM HOPPERSOOT AND FLY ASH FORMATION SEMI-ANNUALLYOR EVERY TWO TONS OF PELLET CLEAN THE VERTICAL EXHAUST DUCTCLEAN EXHAUST HOUSING INSERT ONLY CLEAN THE EXHAUST BLOWERCHECK ALL SEALS CLEAN THE VENTNORMAL OPERATING SOUNDS WIRING DIAGRAM NPI40 ACCESSORIES REPLACEMENTSCOMMON ACCESSORIES NPS40 ACCESSORIESW415-0616 /C COMMON REPLACEMENTS PARTSW415-0616 /C NPS40 REPLACEMENTS PARTSW415-0616 /C NPI40 REPLACEMENTS PARTSCOMMON ACCESSORY PARTS NPI40 ACCESSORY PARTSTROUBLESHOOTING SYMPTOMTEST SOLUTION TROUBLESHOOTING CONTINUED SYMPTOMTEST SOLUTION Burn pot is clean TROUBLESHOOTING CONTINUEDSYMPTOM TEST SOLUTIONSERVICE DESCRIPTION SERVICE AND MAINTENANCE LOGSERVICE DATE SERVICE TECHNICIANW415-0616 /C

Related manuals

Manual 40 pages 42.1 Kb