Napoleon Fireplaces NPI40, NPS40 Hearth Mount Installation, Prior To Installation, Recommended

Page 18
HEARTH MOUNT INSTALLATION

18

HEARTH MOUNT INSTALLATION

Vertical Cap

Storm Collar

Chimney Cap

Figure 17

Pellet

Liner (Recommended)

Flue Cover

Clean-outPRIOR TO INSTALLATION tee INSTALLATIONINTOAMASONRYFIREPLACE

Pellet

Vent

6”

MIN

Floor

Manual backgroundManual backgroundManual backgroundProtection Bring outside air

to the stove Outside Air

(Recommended)

PRIOR TO INSTALLATION

Clean all ashes out of the inside of the fi replace. Make sure that the chimney and fi replace are free of cracks, loose mortar, cresote deposits, blockage or other signs of deterioration. If necessary, have any repair work done by a qualifi ed professional before installing the insert.

Do not remove bricks or mortar from the fi replace.

INSTALLATIONINTOAMASONRYFIREPLACE

1.Remove the fi replace damper or fasten it permanently open.

2.Measure the throat of the fi replace and mark this shape on a piece of 24 gauge sheet metal (fl ue cover). Cut a hole sized for the pellet liner to lie directly below the fi replace fl ue opening. Allow two inches of material for a fl ange on all sides and cut to these measurements. Bend down the fl anges. If you have never done this before, it might be a good idea to make a cardboard pattern and test it fi rst. fasten this fl ue cover in position as high as possible with two masonry screws per side through the fl anges into the fi replace.

3.If you plan on connecting outside air it is recommended to do so at this time.

4.Connect the pellet vent with a clean out tee to the back of the stove. Refer to manufacturer's installation instructions and the "General Venting Section".

5.Run a liner down the chimney and connect to tee.

6.Position the stove in it's fi nal location.

7.Pull the excess length of liner out through the top of the chimney. Trim the excess liner, install the cap and cap the chimney.

W415-0616 / C / 06.04.08

Image 18
Contents W415-0616 /C $10.00W415-0616 /C TABLE of CONTENTS PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCEWARRANTY CONDITIONS AND LIMITATIONSWARNINGS AND SAFETY PRECAUTIONS W415-0616 /CWARNINGS AND SAFETY PRECAUTIONS W415-0616 /CGENERAL INSTRUCTIONS SPECIFICATIONS HEATING SPECIFICATIONSGENERAL INTRODUCTION PELLET QUALITYDIMENSIONS Figures 1a-bFigures 2a-c DIMENSIONS CONTINUED Figures 3a-cDIMENSIONS CONTINUED Figures 4a-cNPI40 with AK8 Adapter and GICSK Flashing Shown PLANNING YOUR INSTALLATION GENERAL INSTALLATIONSPECIFICATIONS HEATER PLACEMENTFLOOR PROTECTION REQUIREMENTS INSTALLATION OPTIONSSAFETY FEATURES OUTSIDE AIRMOBILE HOME INSTALLING THE PELLET VENTGENERAL VENTING TYPE OF VENTPELLET VENT TERMINATION ALCOVE INSTALLATION NPS40 ONLYVENTING THE PELLET HEATER Minimum Alcove DimensionsMINIMUM AIR TERMINAL INSTALLATIONS J D ABBFI LG H ECORNER INSTALLATION NPS40 INSTALLATIONSTRAIGHT INSTALLATION MINIMUM CLEARANCE TO COMBUSTIBLESTERMINATION INSTALLATION VENTING INSTALLATION EXAMPLESHORIZONTAL EXHAUST THROUGH WALL INSTALLATION THROUGH WALL WITH VERTICAL RISE AND HORIZONTALMINIMUM INSIDE VERTICAL CLEARANCES CLASS A CHIMNEY RETROFITINSTALLATIONINTOAMASONRYFIREPLACE HEARTH MOUNT INSTALLATIONPRIOR TO INSTALLATION RecommendedMINIMUM MANTEL CLEARANCES NPI40 INSTALLATIONMINIMUM CLEARANCES TO COMBUSTIBLES REAR TO TOP VENT CONVERSION INSTRUCTIONSNPI40 INSTALLATION OVERVIEW VERTICAL LINER INSTALLATION INSTALLATION INTO A MASONRY FIREPLACEHORIZONTAL VENT INSTALLATION PRIOR TO INSTALLATIONPRIOR TO INSTALLATION INSTALLATION INTO A FACTORY BUILT METAL FIREPLACELINER INSTALLATION INSTALLATION INTO A MASONRY FIREPLACEFigure 24a INSTALLATION INTO A COMBUSTIBLE BUILT-INENCLOSUREMINIMUM FRAMING DIMENSIONS Figure 24bFLASHING INSTALLATION NPI40 FINISHINGMINIMUM ENCLOSURE CLEARANCES LIGHTING HEATER MANUALLY INSTALL VIEWING DOOR NPS40 AND NPI40TRIVET NPI40 PROPER PELLET LOADINGOPERATING INSTRUCTIONS START-UPSHUT-DOWN CLEANING GLASS DOOR GENERAL MAINTENANCE NPS40 AND NPI40DAILY WHENEVER USING THE HEATER OPEN MAIN VIEWING DOORCLEANING THE HEAT EXCHANGE TUBES MAKE SURE PELLETS ARE NOT PILING UPCLEANING THE BURN POT BI-WEEKLYOR EVERY 10 BAGS OF PELLETSVACUUM FIREBOX SEMI-ANNUALLYOR EVERY TWO TONS OF PELLET VACUUM HOPPERSOOT AND FLY ASH FORMATION CLEAN THE EXHAUST BLOWER CLEAN THE VERTICAL EXHAUST DUCTCLEAN EXHAUST HOUSING INSERT ONLY SEMI-ANNUALLYOR EVERY TWO TONS OF PELLETCLEAN THE VENT CHECK ALL SEALSNORMAL OPERATING SOUNDS WIRING DIAGRAM NPS40 ACCESSORIES REPLACEMENTSCOMMON ACCESSORIES NPI40 ACCESSORIESCOMMON REPLACEMENTS PARTS W415-0616 /CNPS40 REPLACEMENTS PARTS W415-0616 /CNPI40 REPLACEMENTS PARTS W415-0616 /CNPI40 ACCESSORY PARTS COMMON ACCESSORY PARTSTROUBLESHOOTING SYMPTOMTEST SOLUTION TROUBLESHOOTING CONTINUED SYMPTOMTEST SOLUTION TEST SOLUTION TROUBLESHOOTING CONTINUEDSYMPTOM Burn pot is cleanSERVICE TECHNICIAN SERVICE AND MAINTENANCE LOGSERVICE DATE SERVICE DESCRIPTIONW415-0616 /C
Related manuals
Manual 40 pages 42.1 Kb