Napoleon Fireplaces TRIVET NPI40, INSTALL VIEWING DOOR NPS40 AND NPI40, Proper Pellet Loading

Page 25
TRIVET NPI40
W415-0616 / C / 06.04.08

TRIVET NPI40

The trivet for the NPI40 is attached by two set screws on the inside of the hopper lid.

INSTALL VIEWING DOOR NPS40 AND NPI40

The main viewing door has been boxed separate from the heater, but MUST be installed before burning the heater.

1.Open both side panels, exposing the bushing on the left and the latches on the right.

Figure 33

2.Align the pins on the door to the bushing on the left side of the heater. Lower into place until both bushings touch.

(Insert

3. Engage the latch hooks into the door frame. Snap the rear handle hook to Illustrated) lock the latch closed.

25

Figure 32

LIGHTING HEATER MANUALLY

Your heater can be lit manually without using the automatic igniter by following the procedure below.

!WARNING

Heater may be hot.

Other than placing a handful of pellets in the burn pot for lighting manually, never feed pellets through the glass viewing door. An "OVERFIRE" condition could occur, if more pellets enter the firebox then what the feed tube can deliver. Pellets must only be burned within the burn pot.

1.Press the start switch

2.Turn feed dial to "Optimum"

3.Place a "handful" of pellets into the burn pot.

4.Cover with a small amount of approved (non-volatile) fi re starter gel.

5.Light fi re starter with a match and close the viewing door.

PROPER PELLET LOADING

Before loading pellets into the hopper first transfer the pellets from it's original plastic bag to a metal bucket. NOTE: If the pellets are kept in the plastic bag, the bag may come in contact with the heater causing the bag to melt and the pellets to spill.

DO NOT load pellets into the hopper if they have been exposed to moisture. Moisture can cause pellets to swell and cause blockage in the feed system. Thoroughly dry pellets before placing into hopper.

Image 25
Contents $10.00 W415-0616 /CW415-0616 /C PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE TABLE of CONTENTSCONDITIONS AND LIMITATIONS WARRANTYW415-0616 /C WARNINGS AND SAFETY PRECAUTIONSW415-0616 /C WARNINGS AND SAFETY PRECAUTIONSGENERAL INTRODUCTION SPECIFICATIONS HEATING SPECIFICATIONSGENERAL INSTRUCTIONS PELLET QUALITYFigures 1a-b DIMENSIONSFigures 2a-c Figures 3a-c DIMENSIONS CONTINUEDFigures 4a-c DIMENSIONS CONTINUEDNPI40 with AK8 Adapter and GICSK Flashing Shown SPECIFICATIONS GENERAL INSTALLATIONPLANNING YOUR INSTALLATION HEATER PLACEMENTSAFETY FEATURES INSTALLATION OPTIONSFLOOR PROTECTION REQUIREMENTS OUTSIDE AIRGENERAL VENTING INSTALLING THE PELLET VENTMOBILE HOME TYPE OF VENTVENTING THE PELLET HEATER ALCOVE INSTALLATION NPS40 ONLYPELLET VENT TERMINATION Minimum Alcove DimensionsJ D ABBFI LG H E MINIMUM AIR TERMINAL INSTALLATIONSSTRAIGHT INSTALLATION NPS40 INSTALLATIONCORNER INSTALLATION MINIMUM CLEARANCE TO COMBUSTIBLESHORIZONTAL EXHAUST THROUGH WALL INSTALLATION VENTING INSTALLATION EXAMPLESTERMINATION INSTALLATION THROUGH WALL WITH VERTICAL RISE AND HORIZONTALCLASS A CHIMNEY RETROFIT MINIMUM INSIDE VERTICAL CLEARANCESPRIOR TO INSTALLATION HEARTH MOUNT INSTALLATIONINSTALLATIONINTOAMASONRYFIREPLACE RecommendedMINIMUM CLEARANCES TO COMBUSTIBLES NPI40 INSTALLATIONMINIMUM MANTEL CLEARANCES REAR TO TOP VENT CONVERSION INSTRUCTIONSNPI40 INSTALLATION OVERVIEW HORIZONTAL VENT INSTALLATION INSTALLATION INTO A MASONRY FIREPLACEVERTICAL LINER INSTALLATION PRIOR TO INSTALLATIONLINER INSTALLATION INSTALLATION INTO A FACTORY BUILT METAL FIREPLACEPRIOR TO INSTALLATION INSTALLATION INTO A MASONRY FIREPLACEMINIMUM FRAMING DIMENSIONS INSTALLATION INTO A COMBUSTIBLE BUILT-INENCLOSUREFigure 24a Figure 24bNPI40 FINISHING FLASHING INSTALLATIONMINIMUM ENCLOSURE CLEARANCES TRIVET NPI40 INSTALL VIEWING DOOR NPS40 AND NPI40LIGHTING HEATER MANUALLY PROPER PELLET LOADINGSTART-UP OPERATING INSTRUCTIONSSHUT-DOWN DAILY WHENEVER USING THE HEATER GENERAL MAINTENANCE NPS40 AND NPI40CLEANING GLASS DOOR OPEN MAIN VIEWING DOORMAKE SURE PELLETS ARE NOT PILING UP CLEANING THE HEAT EXCHANGE TUBESBI-WEEKLYOR EVERY 10 BAGS OF PELLETS CLEANING THE BURN POTVACUUM FIREBOX VACUUM HOPPER SEMI-ANNUALLYOR EVERY TWO TONS OF PELLETSOOT AND FLY ASH FORMATION CLEAN EXHAUST HOUSING INSERT ONLY CLEAN THE VERTICAL EXHAUST DUCTCLEAN THE EXHAUST BLOWER SEMI-ANNUALLYOR EVERY TWO TONS OF PELLETCHECK ALL SEALS CLEAN THE VENTNORMAL OPERATING SOUNDS WIRING DIAGRAM COMMON ACCESSORIES REPLACEMENTSNPS40 ACCESSORIES NPI40 ACCESSORIESW415-0616 /C COMMON REPLACEMENTS PARTSW415-0616 /C NPS40 REPLACEMENTS PARTSW415-0616 /C NPI40 REPLACEMENTS PARTSCOMMON ACCESSORY PARTS NPI40 ACCESSORY PARTSSYMPTOM TROUBLESHOOTINGTEST SOLUTION SYMPTOM TROUBLESHOOTING CONTINUEDTEST SOLUTION SYMPTOM TROUBLESHOOTING CONTINUEDTEST SOLUTION Burn pot is cleanSERVICE DATE SERVICE AND MAINTENANCE LOGSERVICE TECHNICIAN SERVICE DESCRIPTIONW415-0616 /C
Related manuals
Manual 40 pages 42.1 Kb