Vermont Casting RDVOD manual Local Path On Path

Page 26

Radiance Direct Vent/Natural Vent Gas Heater

Comfort Valve System Control Sequence Of Operation With Transmitter

Set manual switch				Five minute wait
to local or remote				period

Light pilot burner

Did the LED stop

blinking?

Release pilotstat

knob.

Yes

Turn pilotstat knob from PILOT to ON.

	No		Review LED fail-
			ure analysis.
			ure analysis.

Cycle switch

once and leave in remote. Press any key on transmit- ter for recognition

operation.

Choose Manual or Remote path. Set switch to manual or remote.

Local Path

On Path

If manual switch is set to LOCAL, did main burner light and fan turn on?

Yes

Turn pilotstat knob

Move switch from

local to remote.

Press any key on transmitter. Move switch back to local.

If the manual switch is set to REMOTE, press the mode but-

ton to display “ON”. does transmitter con-

trol the main burner

and fan?

Move switch from manual to remote. Press any key on transmitter.

to PILOT to turn off main burner.

Turn pilotstat knob

to OFF to turn

valve completely

off.

Yes

	Does transmitter					No
	change levels of					No
	change levels of

	ﬂame height, fan
		speed?

Yes

	Set levels of ﬂame
	height and fan to
	“0” to shut off main
	burner				and fan.
	burner				and fan.

Turn pilotstat knob

to OFF to turn

valve completely

off.

2828

20004188

Image 26

Contents Radiance Direct Vent/Natural Vent Gas Heater Installation & Operating Instructions Radiance Direct Vent/Natural Vent Stove Dimensions Radiance dimensionsClearance Requirements Installation RequirementsLocating The Stove Hearth Requirements Wall Centerline from FloorWall and Ceiling Clearances High Elevations Gas SpeciﬁcationsGas Inlet and Manifold Pressures Horizontal Termination Direct Vent onlyVent Termination Clearances Restictor Plate is used on Direct Vent installations onlyVertical Termination Direct Vent only Location of Vent Termination Canadian Installations US Installations General Venting Information Termination LocationVenting Requirements Natural Vent Only Plate supplied with the stove is not usedVenting Requirements and Options Direct Vent only Approved Vent System ComponentsTools Required Assembly ProceduresParts Bag Contents Unpack and Assemble LegsInstall the Optional Fan Remove rear shroudFor Canadian installations The venting system must Venting System Assembly Direct Vent General InformationInstall the Vent Adapter Pipe Attach the Inner Vent Assembly to the stoveDiscard the inner starter pipe shipped with the log Side Wall Termination AssemblyInstall the Outer Adapter Pipe. Orient the verti Measure the horizontal length Vertical Through the Roof Vent Assembly Vent Termination Below GradeVenting System Assembly Natural Vent General Information Install ﬁrestops and attic insulation shieldInstall the Vent Pipe Install Log SetInstall the left and right rear logs and the right log Connect the Gas Supply LineBurner Information Install ON/OFF SwitchInstall the Mesh and Grille Thermostat Connection optionalOperation Flame & Temperature AdjustmentFlame Characteristics Your First FireLighting and Operating Instructions To Turn Off Gas To HeaterTroubleshooting / Honeywell #8420 Gas Control System Symptom Possible Causes Corrective ActionOn Manual Mode Shut Off ProcedureTransmitter Operation Off Mode Delay Timer ModeLocal Path On Path Auto Path Change Between F/C Temperature Units Auto ModeFan Override During Auto Mode Disable Thermostat FunctionAll Models Air Shutter AdjustmentInjector Oriﬁce Size Matrix Conversion to Natural Gas Input BTU/hMaintenance Check the Gas Flame Regularly Gasket ReplacementInspect the Vent System Annually Wiring Diagrams BLKRadiance Direct Vent/Natural Vent Gas Heater Rdvod DescriptionRadiance Direct Vent/Natural Vent Gas Heater Rdvod Fuel Conversion Kits Shell Enamel Parts Radiance Direct Vent / Natural VentOptional Accessories Limited Lifetime Warranty Efﬁciency Ratings Model EnerGuide Ratings Fireplace Efﬁciency %