Superior DR-400CMP Mantel Clearances, Inches mm, Cold Climate Insulation, Model No, Description

A hearth extension is not required with this appliance. If a hearth extension is used, do not block the lower control compartment door. Any hearth extension used is for appearance only and does not have to conform to standard hearth extension installation requirements.

Note: Combustible wall finish materials and/or surround materials must not be allowed to encroach the area defined by the appliance front face (black sheet metal). Never allow combustible materials to be positioned in front of or overlapping the appliance front face. See Figures 55 and 56 on page 23.

Non-combustible materials, such as surrounds and other appliance trim, may be installed on the appliance front face with these exceptions: they must not cover any portion of the glass or louvers; they may cover any portion of the top radiant panel or the air gaps surrounding the top radiant panel up to the installed hood.

Vertical installation clearances to combustible mantels vary according to the depth of the mantel. (See Figure 58 ). Mantels constructed of non- combustible materials may be installed at any height above the appliance opening; however, do not allow anything to hang below the hood.

Combustible materials may project beyond the sides of the fireplace opening as long as they are kept within the shaded areas illustrated in Figure 57.

Combustible Materials
Allowed In Shaded		Top View Of
Area “Safe Zone”
		Fireplace
12"
	45°	5"
17"
		Min. Distance
		8 ¹⁄₄" To Protected
Side		Side Wall
Wall	Side
	Wall	Min. Distance To
14"
		Unprotected Side Wall

Figure 57

MANTEL CLEARANCES

					Inches (mm)
						12 (305) MANTEL
							10 (254) MANTEL
							8 (203) MANTEL
							6 (152) MANTEL
14	12
(356)	(305)	10					4 (102) MANTEL
		(254)
			8
				6				2 (51) MANTEL
			(203)
				(152)		4
						(102)
			NOTE - Hood shown as positioned
			in louvered front model. The hood
			position in the flush faced front model
			is lower than shown.

Figure 58

TOP OF APPLIANCE

COLD CLIMATE INSULATION

If you live in a cold climate, seal all cracks around your appliance with noncombustible material and wherever cold air could enter the room. It is especially important to insulate outside chase cavity between studs and under floor on which appliance rests, if floor is above ground level.

INSTALLATION ACCESSORIES

Listed Secure Vent™Components

Cat.	Model No.	Description
No.
86L95	SV4.5HTR	Horizontal Round Termination
		with Firestop/Spacer (96K80)
		and Adapter (74L61)
98L27	SV4.5HTSSL	Horizontal Long Small Square
		Termination with
		Firestop/Spacer (96K80) and
		12 in. (305 mm) vent section
		(77L71)
86L97	SV4.5HTS	Horizontal Square Termination
		with Firestop/Spacer (96K80)
		and Adapter (74L61)
94L10	SV4.5HTSS	Horizontal Short Square
		Termination with
		Firestop/Spacer (96K80) and
		Adapter (74L61)
H2152	SV4.5CGV-1	Vertical Termination

Listed Secure Flex™Components

Cat.	Model	Description
No.	No.

These termination kits include firestop/spacer, gear clamps and flex adapter.

86L94	SF-HTR	Horizontal Round Termination
		without Flex
77L82	SFKIT12R	Flex Round Term. with 12 in.
		(305 mm) of *compressed Flex
77L83	SFKIT18R	Flex Round Term. with 18 in.
		(457 mm) of *compressed Flex
77L84	SFKIT24R	Flex Round Term. with 24 in.
		(610 mm) of *compressed Flex
77L85	SFKIT36R	Flex Round Term. with 36 in.
		(914 mm) *compressed Flex
77L86	SFKIT48R	Flex Round Term. with 48 in.
		(1219 mm) of *compressed Flex
87L01	SFHRK	Snorkel Riser Kit with Flex
		Adapter, a section of Flex, and
		Gear Clamps

19M40	SF4.5HF	Firestop/Spacer-
		Horizontal (3-1-1 spacing)
19M41	SF4.5BF	Firestop/Spacer-
		Vertical (1-1-1 spacing)

*All compressed flex vents can be expanded up to two times.

24

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.