Carrier 58PHA/PHX instruction manual Upflowdownflow Horizontal

Page 15

UPFLOWDOWNFLOW HORIZONTAL

90°

YES

120°	YES
MIN

NO

OUTER DOOR

ASSEMBLY

8" (203mm) MIN

FOR DOOR REMOVAL

(2)HEX NUTS, (2) WASHERS & (2) LOCK WASHERS REQ. PER ROD

90°

YES	YES

120°	YES	120°	YES
MIN		MIN

NO

NO

A02020

Fig. 14 - Duct Flanges

1/4" (6mm) THREADED ROD

4 REQ.

SECURE ANGLE

IRON TO BOTTOM

OF FURNACE WITH

3 #8 x 3/4" (19mm) SCREWS TYPICAL FOR 2 SUPPORTS

1” (25mm) SQUARE, 1-1/4”x1-1/4”x1/8” (32x32x3mm)

ANGLE IRON OR UNI-STRUT MAY BE USED

58PHA

A05027

Fig. 15 - Horizontal Unit Suspension

15

Image 15

Contents Ama Furnace Reliability Hazard Safety ConsiderationsCUT Hazard IntroductionClearances to Combustibles Codes and StandardsVenting Electrostatic Discharge ESD Precautions ProcedureLocation GeneralCarbon Monoxide Poisoning Hazard Personal Injury AND/OR Property Damage Hazard Electrical Operation HazardLocation Relative to Cooling Equipment AIR for Combustion VentilationFire Hazard Furnace Corrosion HazardACH Side Return Air Inlet InstallationCombination of Indoor and Outdoor Air Bottom Return Air InletLeveling Legs Downflow InstallationA08556 Roll-Out Protection Opening Dimensions In. mmSuspended Furnace Support Platform Furnace SupportDuctwork Acoustical Treatment Supply Air Connections Filter Arrangement Carbon Monoxide and Poisoning HazardAIR Ducts General RequirementsUpflowdownflow Horizontal Horizontal Suspension with Straps Return Air Connections GAS Piping Fire or Explosion HazardFurnace Overheat Hazard Maximum Capacity of Pipe Air Delivery CFM With FilterUpflow Return Air Configurations and Restrictions Horizontal Return Air Configurations and Restrictions Electrical Data Electrical Connections Electrical Shock HazardElectrical Shock and Fire Hazard Electrical Connection to J-BOX WiringFurnace MAY not Operate BOX RelocationVenting Power Cord Installation in Furnace J-BOXBX Cable Installation in Furnace J-BOX AccessoriesFurnace Control Masonry Chimney Requirements General Venting RequirementsSingle-Stage Furnace with Single-Speed Air Con Ditioner Humidfier Internal Area of Chimney Appliance Application RequirementsChimney Inspection Chart Additional Venting Requirements Burn HazardSidewall Venting Upflow Application-Vent Elbow Up See Notes 1,2,4,5,7,8,9 on See Notes 1,2,4,5,7,8,9 Venting Notes for Figures Using Tin Snips to Cut Tie PointsRounded End of Knockout START-UP, ADJUSTMENT, and Safety Check Fire and Explosion HazardFurnace Damage Hazard Canada Follow exclusively the National Fuel Gas CodeAltitude Derate Multiplier for U.S.A Gas Control Valve Check Safety Controls Speed SelectionFurnace Overheating Hazard Gas Rate Cu Ft./Hr ChecklistA08220 A08220A Electrical SHOCK, Fire or Explosion Hazard Service and Maintenance ProceduresElectrical Controls and Wiring Electrical Shock Hazard FIRE, INJURY, or Death HazardA08221 Service Filter Size Information In. / mm Care and Maintenance Fire or Explosion HazardCleaning AND/OR Replacing AIR Filter Carbon Monoxide Poisoning Fire HazardUnit Damage Hazard Cleaning Heat ExchangerIgniter Position-Side View Sequence of Operation Cleaning Heat Exchanger CellTwo-Speed Cooling Cooling ModeThermidistat Mode Continuous Blower ModeWiring Diagrams TroubleshootingHeat pump Wiring Diagram Troubleshooting Guide Catalog No 58PHA---03SI