Honeywell K5305-1V5 Completing Zone Programming, ∗58 Expert Programming Mode Procedures

Page 40

Installation and Setup Guide

E n t d A 0 2 2 - 4 0 6 3 1 R c v d A 0 2 2 - 4 0 6 4 1

If Serial or Loop Numbers do not match after activating the transmitter

[∗] to continue

If the serial number transmitted does not match the serial number entered, a display similar to the one shown appears. If the loop number does not match, it will also be displayed.

If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary display does not appear), press the [#] key twice and then enter (or transmit) the correct serial number.

10 INPUT S/N: L

A000 - 000 0 0

To Delete a Serial No.

0 in loop number field = delete serial number; # = undo deletion; [∗] to continue

To delete an existing serial number, enter 0 in the loop number field. The serial number will change to 0's.

If 0 was entered in error, simply re-enter the loop number or press [#], and the serial number will return to the display.

Zn ZT RC In: L

10 03 10 RF: 1s

Summary Screen

[∗] to continue

If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and a summary display will appear, showing that zone's programming. Note that an “s” indicates that a transmitter’s serial number has been enrolled.

Press [∗] to accept the zone information and continue.

PROGRAM ALPHA? 0 = NO 1 = YES 0

Alpha Descriptors

0 = no; 1 = yes; [∗] to continue

If you want to program descriptors for zones now, enter 1 (Yes) and refer to the Alpha Descriptor Programming section for available descriptors.

EN TE R Z N N U M . (00 = QUI T) 11

Next Zone Number

[∗] to continue; 00 = quit

If 0 (No) was entered above, the system will return you to the ENTER ZN NUM. prompt for the next zone.

When all zones have been programmed, enter 00 to quit.

Completing Zone Programming

•When you have finished programming all zones, test each zone using the system’s TEST mode.

•Do not use the Transmitter ID Sniffer Mode for checking wireless transmitting devices, as it will only check for transmission of one zone on a particular transmitter, NOT the zones assigned to each additional loop.

NOTE: Following the successful enrollment of each wireless device, note the device serial number in the appropriate column on the ENROLLED TRANSMITTERS worksheet in the Programming Form; then enter the other information (zone number, zone type, loop number, etc.) relevant to that device.

∗58 Expert Programming Mode Procedures

This method is designed for use by installers with previous experience in programming ADEMCO control panels. This mode is also used to program wireless keys using pre-defined templates.

Start Expert Programming mode by pressing ✱58 while in Data Programming mode.

SET TO CONFIRM?

0 = NO 1 = YES 0

Confirm?

0 = no; 1 = yes; [∗] to continue

This display appears upon entry into this mode.

The default is 0 (No).

If 1 (Yes) is entered, you will be prompted to confirm each transmitter after entering the serial and loop numbers (at the “XMIT TO CONFIRM” prompt later).

5-4

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Ademco Vista Series Recommendations for Proper Protection Table Of Contents Table Of Contents Features and Installation Highlights Capabilities and FunctionsCompatible Devices Important Installation Highlights Installer Please ReadDevice Mounting and Wiring the Control Installing the Control Cabinet and PC BoardAuxiliary Device Current Draw Worksheet AC Power, Battery, and Ground Connections Wire Run ChartConnecting the Keypads and Other Addressable Devices Sounder Bell ConnectionsBasic Connections Supervised outputTable of Device Addresses Keypad NotesLong Range Radio Connections Size MA or less 100 mA 300 mA 500 mA 600 mAHardwire Zones and Zone Expansion Smoke Detector Notes ZonesInstalling the RF Receiver and Wireless Transmitter Zones Compatible ReceiversRF Receiver No. of Zones Receiver ConnectionsInstalling a 5800TM InstallingTransmitter Battery Life ModuleInstalling a Keyswitch Keyswitch ConnectionsPowerline Carrier Devices 4204/4229 Relay ModulesOn-Board Triggers With the control as shown belowPhone Module Problems Phone Line 4285/4286 Phone ModuleAudio Alarm Verification Connections AAV, listen-In BankAbout Programming Programming OverviewMechanics of Programming Zone Type Definitions Alarm by Night Hr Silent AlarmAlarm Auxiliary AlarmNo Alarm KeyswitchConfigurable Response TypeSystem Setup Fields ∗20 ∗29 Data Field ProgrammingAbout Data Field Programming Zone Sounds & Timing ∗31-∗39Dialer Programming ∗40 ∗50 Burglary Dialer Delay Dynamic Signaling DelayDynamic Signaling Priority Zone Programming Menu ModeSystem Status Report Codes Miscellaneous System Fields Misc. Fault Delay Time Program Mode Lockout OptionsEvent Log Enables Phone Line Monitor EnablePager Programming Fields 172Pager Delay Option for Alarms Clean Me OptionPager 1 Characters Pager 1 Report OptionsConfigurable Zone Type Fields Configurable Zone TypeConfigurable Zone Type Options Zone Type 90 Report CodesConfigurable Zone Type Charts Zone Conditions Represented EntriesTouch Screen Keypad AUI Enable Keypad Programming FieldsInstallation and Setup Guide Menu Mode Programming Zone Programming ProcedureZones and Partitions About Zone Programming ∗56 and ∗58 Menu ModesHardwire Type Zone NumberSummary Screen Zone Type ZTInput Device type Serial number Entry and Loop Number EntryLoop Number Change Enroll Summary∗58 Expert Programming Mode Procedures Completing Zone ProgrammingZone Programming Serial numberTo Delete a Serial Number ConfirmWireless Key Programming Templates Template NumberTemplate Display PartitionWireless Key Predefined Default Templates Wireless Key Transmitter5804BD 2-Way Wireless Key Transmitter Not ConfirmedAbout Output Device Programming *79/*80 Menu Mode Menu Mode Output Device MappingProgramming Output Devices Output IdentificationRelay Position Output TypeModule Addresses Output Function No Menu Mode Defining Output FunctionsActivated By Output Action 01-08 = zone list ∗ to continue= off = Change Device State = Close for 2 seconds = Stay ClosedAbout Zone Lists *81 Menu Mode Zone List ProgrammingAbout Function Keys *57 Menu Mode Programming Function KeysFunction Key Partition NumbeAbout Descriptor Programming *82 Menu Mode Programming Zone Descriptors Menu Mode ∗82Accept First Word Second 3-Digit Index NoAccept Second Word Assigning Partition/Custom Message DescriptorsCharacter Ascii Chart For Adding Custom Words For Entering Zone DescriptorsSchedule Number Programming Installer and User SchedulesStart Time = repeat every third week 4 = repeat every fourth week Repeat OptionRandomize For events 01 System Communication and Operation Panel Communication with Central StationReport Code Formats DigitWhere Code for Type +1/4+1 Report Standard ExpandedSome event codes may not apply to certain control panels Ademco Contact IDCode Definition Keyfob must be enrolled in system first see Wireless Key System Security CodesAttributes Values Level User No FunctionsKeypad Commands Keypad FunctionsVoice Keypads Function DescriptionSetting the Real-Time Clock Keys Displayed as Zone ∗ /1 ∗ /#Various System Trouble Displays Alpha Display Fixed Disp MeaningInstallation and Setup Guide Testing the System About Test ProceduresChecking Transmitter Enrollment Sniffer Mode System TestGo/No Go Test Mode Automatic Standby Battery TestsDialer Communication Test and Periodic Test Reports Automatic Periodic Test ReportSpecifications & Accessories Security ControlElectrical CommunicationWire Smoke Detector Detector TypeCompatible 5800 Series Transmitters Table Series Transmitter Input Loop IdentificationModel Product Input Type Description Can be used to turn the burglary protection on and off 5827 Wireless KeypadTo be transmitted Regulatory Agency Statements Industrie CanadaUL Notices Page Installation and Setup Guide Page Installation and Setup Guide Limitations and Warranty Limitations of this Alarm System10-8 Index 10-10 Summary of Connections Limited Warranty K5305-1V5 10/04 Rev. a
Top Page Image Contents