Honeywell VISTA 20P, VISTA-20PSIA, VISTA-15P, VISTA-15PSIA Menu Mode Programming, Set to Confirm

Page 37

S E C T I O N 5

Menu Mode Programming

Zones and Partitions

Each protection zone needs to be programmed with various attributes using *56 Zone Programming mode or ✱58 Expert Programming Mode.

The VISTA-20P system can control two independent areas of protection (known as partitions) for use by independent users, if desired, by simply assigning zones to one or the other partition during zone programming. The VISTA-20P, by default, automatically distributes users between the two partitions. The master user can change the user number distributions.

Zones can also be assigned to a common partition, which is an area shared by users of both partitions (such as a lobby in a building). This allows either partition to arm, while leaving the common partition disarmed for access into the other partition. The following describes the functioning of the VISTA-20P common partition:

•The common zone sounds and reports alarms only when both partitions are armed. If only one partition is armed, the system ignores faults on the common zone.

•Either partition may arm its system if the common zone is faulted, but once armed, the other partition will not be able to arm unless the common zone is first bypassed or the fault is corrected.

•Faults on the common zone are displayed on common zone keypads, and will also appear on another partition’s keypad when that partition is armed.

•Either partition can clear and restore the common zone after an alarm.

About Zone Programming (∗56 and ∗58 Menu Modes)

•Used to program zones, zone types, report codes, enroll 5800 RF Wireless Transmitter serial numbers, and identify the type of loop input device(s).

•Can also be used to enter alpha descriptors for programmed zones; however, we recommend entering descriptors in menu mode ✱82 (Alpha Descriptor Programming after all zone programming has been completed).

•*58 Expert Programming mode provides a faster method of zone programming than *56 Menu mode, but is recommended only for those who have had previous experience in programming controls of this type.

NOTE: Alpha display prompts are shown in a double-line box.

✱56 Zone Programming Procedure

1.Enter the zone number to be programmed.

2.Make appropriate entries at the prompts.

3.Confirm the serial number of wireless transmitter zones.

Start Zone Programming mode by pressing ✱56 while in Data Programming mode.

SET TO CONFIRM? 0 = NO 1 = YES

Set to Confirm

0 = no; 1 = yes

If 1 (Yes) is entered, you will be prompted to confirm each transmitter after entering the serial and loop numbers (at the “XMIT TO CONFIRM” prompt later in this procedure). We

recommend that you confirm the programming of every transmitter.

5-1

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Ademco Vista Series Recommendations for Proper Protection Table Of Contents Table Of Contents Capabilities and Functions Features and Installation HighlightsCompatible Devices Important Installation Highlights Installer Please ReadDevice Installing the Control Cabinet and PC Board Mounting and Wiring the ControlAuxiliary Device Current Draw Worksheet Wire Run Chart AC Power, Battery, and Ground ConnectionsSounder Bell Connections Connecting the Keypads and Other Addressable DevicesBasic Connections Supervised outputKeypad Notes Table of Device AddressesLong Range Radio Connections Size MA or less 100 mA 300 mA 500 mA 600 mAHardwire Zones and Zone Expansion Zones Smoke Detector NotesCompatible Receivers Installing the RF Receiver and Wireless Transmitter ZonesRF Receiver No. of Zones Receiver ConnectionsInstalling Installing a 5800TMTransmitter Battery Life ModuleKeyswitch Connections Installing a Keyswitch4204/4229 Relay Modules Powerline Carrier DevicesWith the control as shown below On-Board TriggersPhone Line 4285/4286 Phone Module Phone Module ProblemsBank Audio Alarm Verification Connections AAV, listen-InAbout Programming Programming OverviewMechanics of Programming Zone Type Definitions Hr Silent Alarm Alarm by NightAlarm Auxiliary AlarmKeyswitch No AlarmConfigurable Response TypeData Field Programming System Setup Fields ∗20 ∗29About Data Field Programming Zone Sounds & Timing ∗31-∗39Dialer Programming ∗40 ∗50 Dynamic Signaling Delay Burglary Dialer DelayDynamic Signaling Priority Zone Programming Menu ModeSystem Status Report Codes Miscellaneous System Fields Program Mode Lockout Options Misc. Fault Delay TimeEvent Log Enables Phone Line Monitor EnablePager Programming Fields Clean Me Option 172Pager Delay Option for AlarmsPager 1 Characters Pager 1 Report OptionsConfigurable Zone Type Configurable Zone Type FieldsConfigurable Zone Type Options Zone Type 90 Report CodesZone Conditions Represented Entries Configurable Zone Type ChartsKeypad Programming Fields Touch Screen Keypad AUI EnableInstallation and Setup Guide Zone Programming Procedure Menu Mode ProgrammingZones and Partitions About Zone Programming ∗56 and ∗58 Menu ModesZone Number Hardwire TypeSummary Screen Zone Type ZTSerial number Entry and Loop Number Entry Input Device typeLoop Number Change Enroll SummaryCompleting Zone Programming ∗58 Expert Programming Mode ProceduresSerial number Zone ProgrammingTo Delete a Serial Number ConfirmTemplate Number Wireless Key Programming TemplatesTemplate Display PartitionWireless Key Transmitter Wireless Key Predefined Default Templates5804BD 2-Way Wireless Key Transmitter Not ConfirmedMenu Mode Output Device Mapping About Output Device Programming *79/*80 Menu ModeProgramming Output Devices Output IdentificationRelay Position Output TypeModule Addresses Output Function No Menu Mode Defining Output FunctionsActivated By 01-08 = zone list ∗ to continue Output Action= off = Change Device State = Close for 2 seconds = Stay ClosedZone List Programming About Zone Lists *81 Menu ModeProgramming Function Keys About Function Keys *57 Menu ModeFunction Key Partition NumbeProgramming Zone Descriptors Menu Mode ∗82 About Descriptor Programming *82 Menu ModeSecond 3-Digit Index No Accept First WordAccept Second Word Assigning Partition/Custom Message DescriptorsFor Entering Zone Descriptors Character Ascii Chart For Adding Custom WordsSchedule Number Programming Installer and User SchedulesStart Time = repeat every third week 4 = repeat every fourth week Repeat OptionRandomize For events 01 Panel Communication with Central Station System Communication and OperationReport Code Formats DigitCode for Type +1/4+1 Report Standard Expanded WhereSome event codes may not apply to certain control panels Ademco Contact IDCode Definition System Security Codes Keyfob must be enrolled in system first see Wireless KeyAttributes Values Level User No FunctionsKeypad Functions Keypad CommandsVoice Keypads Function DescriptionKeys Displayed as Zone ∗ /1 ∗ /# Setting the Real-Time ClockAlpha Display Fixed Disp Meaning Various System Trouble DisplaysInstallation and Setup Guide About Test Procedures Testing the SystemChecking Transmitter Enrollment Sniffer Mode System TestAutomatic Standby Battery Tests Go/No Go Test ModeDialer Communication Test and Periodic Test Reports Automatic Periodic Test ReportSecurity Control Specifications & AccessoriesElectrical CommunicationDetector Type Wire Smoke DetectorCompatible 5800 Series Transmitters Table Series Transmitter Input Loop IdentificationModel Product Input Type Description Can be used to turn the burglary protection on and off 5827 Wireless KeypadTo be transmitted Industrie Canada Regulatory Agency StatementsUL Notices Page Installation and Setup Guide Page Installation and Setup Guide Limitations of this Alarm System Limitations and Warranty10-8 Index 10-10 Summary of Connections K5305-1V5 10/04 Rev. a Limited Warranty
Top Page Image Contents