Bosch Appliances MIC612 installation manual Installing the MIC Power Supply Unit PSU

Page 20

20 en Installation

MIC612 Thermal Camera

 

 

example, one of the securing bolts) to the camera’s outside case, and should be attached to the Earth terminal post on the PCD base of the camera.

–If the system is copper throughout and the camera pictures are fed back to the control room via coaxial copper cable, then the camera should be earthed only at the video termination point in the control room. In this case, the "Earth Link" on the PCB should be broken. Refer to Section 4.4.1 Earth Link on PCB, page 21.

–If the video is transmitted back to the control room via some non-electrical connecting medium (for example, fiber optic, radio, or microwave link), then the camera should be earthed at the transmitter point in the power supply unit. The PSU "Earth Link" may be used for this purpose.

–If dual earthing is unavoidable, then a video isolation transformer should be fitted between the two earths.

7.Use M8 x 20 mm stainless steel nuts, bolts, and washers to secure the PCD base of the camera to the mounting bracket. An additional Nebar gasket or suitable silicone sealant can be used to ensure a water tight seal between the base and mounting surface. Tighten all bolts securely.

8.Secure all cabling and conduit.

WARNING!

If the camera is mounted ball down, it is essential that the connector and base area of the camera are completely sealed from water ingress. Any water getting into the connector is liable to cause corrosion to the connector pins, leading to unreliable operation of the camera unit.

WARNING!

To prevent water from penetrating the composite cable connector threads, the 25 mm thread should be sealed at final installation using PTFE tape (not supplied). Alternatively, a suitable sealant may be liberally applied to the thread prior to final tightening.

4.4

Installing the MIC Power Supply Unit (PSU)

Each MIC power supply unit (PSU) provides all of the connections needed for power, video, and telemetry for a single MIC camera. Each MIC PSU has CE and FCC approval and has a cast-aluminum enclosure that is weather-resistant (rated IP65). Features include:

–A provision for driving various optional interface cards mounted internally to the MIC power supply enclosure (for example, an 8-input alarm card (MIC-ALM))

–A provision for a signal interface card (MIC-BP4) to connect telemetry to Bosch Biphase equipment

–Screw termination of all cables (composite, telemetry, and ancillary) into and out of the enclosure

–Earth isolation and termination within the unit to control video earthing correctly and thus prevent earth loops

Each MIC PSU ships with the following parts:

–Three (3) M12 cable glands for telemetry, video and ancillary equipment

–One (1) M16 gland for connection of the shielded composite cable to the MIC camera

–One (1) 1/2 in. NPT cable gland for the power cable connection

–One (1) 1/2 in. NPT and one (1) M12 blanking plug

MIC612 cameras can use the following power supply units: MIC-240PSU-2 (230 VAC), MIC- 115PSU-2 (115 VAC), or MIC-240PSU-2 (24 VAC). The dimensions (H x W x D) of the PSU enclosures are: 90 x 260 x 160 mm (3.54 x 10.24 x 6.3 in.). The weight is 3.2 kg (7.1 lb).

F.01U.249.416 2.0 2012.09

Installation Manual

Bosch Security Systems, Inc.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents MIC612 Thermal Camera Page Table of Contents Common User Commands Advanced FeaturesOn-Screen Display OSD Menus Bosch Protocol On-Screen Display OSD Menus Pelco ProtocolMaintenance and Troubleshooting Keyboard Commands By Number IndexSafety Important Safety InstructionsAbout this Manual Conventions in this ManualMIC612 Thermal Camera Safety en EC Directives Important NoticesCoax grounding Informations FCC ET Ices applications commerciales FCC and Ices ComplianceFCC ET Ices Information commercial applications USA Customer Support and ServiceBosch Notices Parts List 2UnpackingAdditional Products Required Additional Tools RequiredInstallation Overview MIC camera mounting positions Upright, InvertedTypical Mounting Arrangements Number DescriptionMounting Positions About Alarm Inputs and Outputs An 8-input alarm card installed in the MIC PSUAlarm Card Number Installed? Alarm Inputs Alarm Outputs 3About the MIC Shielded Composite CableMIC-BP4 sold separately InstallationTypical Installation Configurations Follow these steps in sequence to install the MIC612 camera Overview of Installation StepsExample 2 Configuration with RS-485 protocol connection Mounting the Camera Installing the MIC Power Supply Unit PSU Earth Link on PCB Fuse Ratings3Layout of MIC Power Supply Units PSUs for MIC612 4Installation Instructions Electrical Shock HazardNumber Description PCB Marking Description AUX2 Number Description Cable Gland SizeAUX1 MIC612 Thermal Camera Installation en Power supply. Follow these steps Disconnect the power supply from the power sourceCommissioning the Camera with Heater Option Fitted LED DescriptionFitting the Optional Sunshield MIC612 Bottom half of the sunshield see stepHead is facing up ScrewdriverEstablishing Control of the Camera via Biphase Protocol Getting StartedEstablishing Control of the Camera Establishing Control of the Camera via RS-485 ProtocolPowering On Controlling the CameraBasic Keyboard Operation LCDNavigating the On-Screen Display OSD Menus Keyboard Commands, Bosch Protocol4Keyboard Commands, Pelco Protocol Preset 4Setting the Addresses of the Two Cameras of the MIC612Special Preset Commands, Pelco Protocol Setting the Address of the Optical Camera via FastAddress FastAddress, Bosch Protocol3FastAddress, Pelco Protocols To set an address for a camera without an addressTo change or clear an address for a camera with an address To set FastAddress with a Pelco KeyboardSetting Passwords Configuring the Camera for Inverted OperationActive Commands in FastAddress Special PasswordsSetup Menu 6On-Screen Display OSD Menus Bosch ProtocolCamera Setup Menu ATWWDR Thermal Camera Setup Menu Lens Setup Menu ManualPTZ Setup Menu Display Setup Menu Display Adjust Camera OSDAzimuth CompassCommunication Setup Menu Communication SetupAutoBaud Baud RateAlarm Setup NoneOutputs Setup Submenu Outputs Setup Submenu ChoicesOutputs OSDRule Setup Submenu Rule SetupRule Setup Submenu Choices Rule # Choices EnabledOutput Language MenuInput Diagnostics Menu BistSecurity Access Ctfid AccessPower Up Events Internal HumidityAlarm Status Submenu Alarm InputAlarm Output Total Time OnOn-Screen Display OSD Menus Pelco Protocol Camera Setup Pelco menu Bosch menu Setup MenuBosch Menu ContinuousPTZ Setup WhiteOutdoor BalanceOther Menus OFFSwitching Video Displaying Thermal Camera TemperatureOperation of the Thermal Camera Flat-Field Correction FFCTriggering Alarms On Detection of Objects Outside of Set Thermal Temperature ThresholdSet the Temperature Threshold Set the Alarm RuleCommon User Commands Setting AutoPan ModeSetting Preset Shots Specifying a Shot or a Sector TitleConfiguring Preposition Tours Programming the Inactivity OperationUsing the Wiper/Washer Recording ToursAdvanced Features 10.1 Alarm Rules10.1.1 Controlling Alarm Rules 10.1.2 Alarm Rule ExamplesExample 2 Advanced Alarm Rule 10.2 Privacy Masking10.5.1 Setting the Azimuth Zero Point 10.3 Image Stabilization10.4 Pre-position Tour 10.5 Azimuth, Elevation, and Compass Directions10.5.2 Displaying Azimuth, Elevation, and Compass Headings 180 / -45 S11Maintenance and Troubleshooting Problem Explanation SolutionCommands, Optical Camera Keyboard Commands By NumberKeyboard Commands Bosch Protocol Zone/Sector Title Menu Enters the Zone Title menu. Refer to Refer to .5 Azimuth, Elevation, Compass Directions,Commands, Thermal Camera 70 en MIC612 Thermal Camera Keyboard Commands Pelco Protocol Keyboard User Action Description CommandEn MIC612 Thermal Camera Pre-compensation 39 sharpness 38 shutter White balance Index#-ENTER En Index MIC612 Thermal Camera Constant focus 41 manual focus 41 spot focus Custom tour PTZShot Zero panPage Page Bosch Security Systems, Inc

MIC612 specifications

The Bosch Appliances MIC612 is an innovative and highly efficient piece of kitchen equipment that enhances the culinary experience for home chefs and professionals alike. Renowned for its quality, Bosch has developed this compact microwave that combines advanced technology with user-friendly features.

One of the standout characteristics of the MIC612 is its sleek design, seamlessly incorporating into various kitchen styles. With its stainless-steel finish, the microwave not only offers aesthetic appeal but also ensures durability and easy maintenance. Its compact size makes it an ideal fit for smaller kitchens or areas where space is limited, while still providing ample cooking capacity.

The MIC612 is equipped with intelligent cooking technology. This includes sensor cooking, which automatically adjusts cooking time and power levels based on moisture detected in the food. This feature simplifies meal preparation by eliminating the need for constant monitoring, ensuring perfectly cooked dishes every time. Additionally, the microwave offers multiple cooking modes, including reheating, defrosting, and cooking with precision.

For those who appreciate convenience, the MIC612 includes pre-programmed settings for common foods like popcorn, pizza, and baked goods. This allows users to enjoy a wide variety of meals with minimal effort. The intuitive control panel and clear digital display enhance the ease of use, enabling quick selection of settings and cooking times.

Safety is a paramount concern for Bosch, and the MIC612 does not disappoint. It features a child safety lock, ensuring that curious little hands cannot accidentally operate the appliance. Moreover, the design incorporates a reliable cooling system to prevent overheating and ensure longevity.

Energy efficiency is another highlight of the Bosch MIC612. It is designed to consume less power compared to traditional microwaves, making it an eco-friendly choice without compromising performance. The combination of cutting-edge technology, thoughtful design, and practical features makes the Bosch Appliances MIC612 a valuable addition to any kitchen, offering versatility and reliability for all cooking needs. Whether reheating leftovers or preparing a fresh meal from scratch, this microwave stands out as a remarkable option for modern culinary tasks.
Top Page Image Contents