Bosch Appliances installation manual MIC612 Thermal Camera Installation en

Page 27

MIC612 Thermal Camera

Installation en 27

 

 

NOTICE!

You must connect the overall shield drain wire of the composite cable to the power supply chassis in order to ground the chassis. Crimp the drain wire to the ring terminal lug attached to the mounting screw of the PCB located to the right of BNC socket CN3 (Video Switched). Refer to Figure 4.3 for the location of the screw.

*If connecting a heater, see Section 4.4.5 Commissioning the Camera with Heater Option Fitted.

19.Slide back the cable so that the shield is in the middle of the gland.

20.Tighten the cable gland so that it grips firmly the shielded composite cable. It is important that the braided cable screen engages with the internal clamps of the cable gland to ensure correct EMC protection.

21.If necessary, connect a tamper switch to terminal block HD2.

22.Make the necessary video connections. Feed the coaxial cable of your choice--see the table below to identify the recommended cable types, maximum distance, and other specifications for the coax video connection between the MIC power supply and the head-end control system--through the top-left M12 cable gland (item 1, Figure 4.7).

Cable Type; Maximum Distance

RG-59/U; 300 m (1000 ft)

 

RG-6/U; 450 m (1500 ft)

 

RG-11/U; 600 m (2000 ft)

Size

O.D. between 4.6 mm (0.181 in.) and 7.9 mm (0.312 in.)

Shield

Copper braid: 95%

Central Conductor

Standard copper center

23.Crimp the end of the cable with a BNC terminal connector.

24.Connect the Video Out cable to BNC socket CN1.

25.For dual video output only: If needed, remove the blanking plug that covers the hole for the bottom-left M12 cable gland (item 3, Figure 4.7). Feed a second Video Out cable through the cable gland, and then connect the switched Video Out cable to BNC socket CN3. This second cable provides control for video from both the optical camera and the thermal camera; users can switch between the two cameras.

26.Feed telemetry cable through the bottom-right M12 cable gland (item 4, Figure 4.7).

27.Connect head-end RS-485 control to terminal block HD5, as indicated in the table below:

PCB Marking

Telemetry

Connection Description /

Pin Number

(non-IR PCBs)

Signal Name

Function

 

RxB

Rx +

RS485+ to camera

1

RxA

Rx -

RS485- to camera

2

0V

Ground

0V from control room

3

TxA

Tx -

RS485- to control room

4

TxB

Tx +

RS485+ to control room

5

Note: The terminal block is positioned with the screw terminals on the left, next to the fuses. Pins are numbered from top to bottom in that orientation. Non-IR PSU PCBs are marked.

28.If connecting to additional add-on cards (for example, a card for 8-input alarms (MIC- 516ALM) or for 8-input alarms plus washer pump drive (MIC-ALM), and/or a Biphase card (MIC-BP4)), remove the second blanking plug that covers one of the holes for an M12 cable gland (item 3, Figure 4.7). Attach the supplied M12 gland. Make the appropriate connections to plug-in terminal CN2.

NOTICE!

For installation of the MIC 8-input Alarm Card (MIC-ALM) or Biphase converter (MIC-BP4), please refer to their respective manuals.

Bosch Security Systems, Inc.

Installation Manual

F.01U.249.416 2.0 2012.09

Image 27
Contents MIC612 Thermal Camera Page Table of Contents On-Screen Display OSD Menus Pelco Protocol Common User CommandsAdvanced Features On-Screen Display OSD Menus Bosch ProtocolIndex Maintenance and Troubleshooting Keyboard Commands By NumberConventions in this Manual SafetyImportant Safety Instructions About this ManualMIC612 Thermal Camera Safety en Important Notices EC DirectivesCoax grounding FCC and Ices Compliance FCC ET Ices Information commercial applicationsInformations FCC ET Ices applications commerciales Customer Support and Service Bosch NoticesUSA Additional Tools Required Parts List2Unpacking Additional Products RequiredMIC camera mounting positions Upright, Inverted Installation OverviewNumber Description Typical Mounting ArrangementsMounting Positions 3About the MIC Shielded Composite Cable About Alarm Inputs and OutputsAn 8-input alarm card installed in the MIC PSU Alarm Card Number Installed? Alarm Inputs Alarm OutputsInstallation Typical Installation ConfigurationsMIC-BP4 sold separately Overview of Installation Steps Example 2 Configuration with RS-485 protocol connectionFollow these steps in sequence to install the MIC612 camera Mounting the Camera Installing the MIC Power Supply Unit PSU Fuse Ratings Earth Link on PCB3Layout of MIC Power Supply Units PSUs for MIC612 Electrical Shock Hazard 4Installation InstructionsNumber Description PCB Marking Description Number Description Cable Gland Size AUX1AUX2 MIC612 Thermal Camera Installation en LED Description Power supply. Follow these stepsDisconnect the power supply from the power source Commissioning the Camera with Heater Option FittedScrewdriver Fitting the Optional Sunshield MIC612Bottom half of the sunshield see step Head is facing upEstablishing Control of the Camera via RS-485 Protocol Establishing Control of the Camera via Biphase ProtocolGetting Started Establishing Control of the CameraLCD Powering OnControlling the Camera Basic Keyboard OperationKeyboard Commands, Bosch Protocol 4Keyboard Commands, Pelco ProtocolNavigating the On-Screen Display OSD Menus 4Setting the Addresses of the Two Cameras of the MIC612 Special Preset Commands, Pelco ProtocolPreset FastAddress, Bosch Protocol Setting the Address of the Optical Camera via FastAddressTo set FastAddress with a Pelco Keyboard 3FastAddress, Pelco ProtocolsTo set an address for a camera without an address To change or clear an address for a camera with an addressSpecial Passwords Setting PasswordsConfiguring the Camera for Inverted Operation Active Commands in FastAddress6On-Screen Display OSD Menus Bosch Protocol Setup MenuATW Camera Setup MenuWDR Thermal Camera Setup Menu Manual Lens Setup MenuPTZ Setup Menu Display Setup Menu Compass Display AdjustCamera OSD AzimuthBaud Rate Communication Setup MenuCommunication Setup AutoBaudNone Alarm SetupOSD Outputs Setup SubmenuOutputs Setup Submenu Choices OutputsRule # Choices Enabled Rule Setup SubmenuRule Setup Rule Setup Submenu ChoicesLanguage Menu InputOutput Bist Diagnostics MenuInternal Humidity Security AccessCtfid Access Power Up EventsTotal Time On Alarm Status SubmenuAlarm Input Alarm OutputOn-Screen Display OSD Menus Pelco Protocol Continuous Camera SetupPelco menu Bosch menu Setup Menu Bosch MenuBalance PTZ SetupWhite OutdoorOFF Other MenusFlat-Field Correction FFC Switching VideoDisplaying Thermal Camera Temperature Operation of the Thermal CameraSet the Alarm Rule Triggering Alarms On Detection of Objects Outside of SetThermal Temperature Threshold Set the Temperature ThresholdSpecifying a Shot or a Sector Title Common User CommandsSetting AutoPan Mode Setting Preset ShotsProgramming the Inactivity Operation Configuring Preposition ToursRecording Tours Using the Wiper/Washer10.1.2 Alarm Rule Examples Advanced Features10.1 Alarm Rules 10.1.1 Controlling Alarm Rules10.2 Privacy Masking Example 2 Advanced Alarm Rule10.5 Azimuth, Elevation, and Compass Directions 10.5.1 Setting the Azimuth Zero Point10.3 Image Stabilization 10.4 Pre-position Tour180 / -45 S 10.5.2 Displaying Azimuth, Elevation, and Compass HeadingsProblem Explanation Solution 11Maintenance and TroubleshootingKeyboard Commands By Number Keyboard Commands Bosch ProtocolCommands, Optical Camera Refer to .5 Azimuth, Elevation, Compass Directions, Zone/Sector Title Menu Enters the Zone Title menu. Refer toCommands, Thermal Camera 70 en MIC612 Thermal Camera Keyboard User Action Description Command Keyboard Commands Pelco ProtocolEn MIC612 Thermal Camera Index #-ENTERPre-compensation 39 sharpness 38 shutter White balance En Index MIC612 Thermal Camera Constant focus 41 manual focus 41 spot focus PTZ Custom tourZero pan ShotPage Page Bosch Security Systems, Inc

MIC612 specifications

The Bosch Appliances MIC612 is an innovative and highly efficient piece of kitchen equipment that enhances the culinary experience for home chefs and professionals alike. Renowned for its quality, Bosch has developed this compact microwave that combines advanced technology with user-friendly features.

One of the standout characteristics of the MIC612 is its sleek design, seamlessly incorporating into various kitchen styles. With its stainless-steel finish, the microwave not only offers aesthetic appeal but also ensures durability and easy maintenance. Its compact size makes it an ideal fit for smaller kitchens or areas where space is limited, while still providing ample cooking capacity.

The MIC612 is equipped with intelligent cooking technology. This includes sensor cooking, which automatically adjusts cooking time and power levels based on moisture detected in the food. This feature simplifies meal preparation by eliminating the need for constant monitoring, ensuring perfectly cooked dishes every time. Additionally, the microwave offers multiple cooking modes, including reheating, defrosting, and cooking with precision.

For those who appreciate convenience, the MIC612 includes pre-programmed settings for common foods like popcorn, pizza, and baked goods. This allows users to enjoy a wide variety of meals with minimal effort. The intuitive control panel and clear digital display enhance the ease of use, enabling quick selection of settings and cooking times.

Safety is a paramount concern for Bosch, and the MIC612 does not disappoint. It features a child safety lock, ensuring that curious little hands cannot accidentally operate the appliance. Moreover, the design incorporates a reliable cooling system to prevent overheating and ensure longevity.

Energy efficiency is another highlight of the Bosch MIC612. It is designed to consume less power compared to traditional microwaves, making it an eco-friendly choice without compromising performance. The combination of cutting-edge technology, thoughtful design, and practical features makes the Bosch Appliances MIC612 a valuable addition to any kitchen, offering versatility and reliability for all cooking needs. Whether reheating leftovers or preparing a fresh meal from scratch, this microwave stands out as a remarkable option for modern culinary tasks.