Bosch Appliances MIC612 3FastAddress, Pelco Protocols, To set FastAddress with a Pelco Keyboard

Page 35

MIC612 Thermal Camera

Getting Started en 35

 

 

–ON-998-ENTER: Displays and programs all cameras with or without an address in the system.

–ON-997-ENTER: Displays the current address status of all cameras in the system simultaneously.

To set an address for a camera without an address:

1.Select the camera number that you want to FastAddress. The system displays the camera number on the keyboard and the image on the corresponding monitor.

2.Press #-ENTER(where # is the camera number without an address).

3.Press ON-999-ENTERto invoke an on-screen display of cameras on the system without an address.

4.Follow the on-screen instructions. You receive an on-screen confirmation when the FastAddress is complete.

To change or clear an address for a camera with an address:

1.Select the camera number that you want to FastAddress. The system displays the camera number on the keyboard and the image on the corresponding monitor.

2.Press #-ENTER(where # is the camera number with an address).

3.Press ON-998-ENTERto invoke an on-screen display of all cameras on the system, with or without an address.

4.Follow the on screen instructions. You receive an on-screen confirmation when the FastAddress is complete.

The table below identifies the setting of the thermal camera when you change the address of the optical camera.

Default Address, Optical

New Address, Optical Camera

Address, Thermal Camera

0

A number other than 0

The number of the optical

 

 

camera + 1

A number other than 0

0 or another number

-No change of address.-

You can change the address of the thermal camera via CTFID; there is no Aux code for this.

5.4.3FastAddress, Pelco Protocols

This section provides instructions to set a FastAddress with a Pelco keyboard or controller.

– The optical camera of the MIC612 with an address set to 0 responds to commands set to any address.

– Pelco-Pprotocol must use addresses 1 to 32.

– Pelco-Dprotocol must use addresses 1 to 254.

NOTICE!

A previously-configured MIC612 with an address above 32 (Pelco-P upper limit) or 254 (Pelco- D upper limit) can be used without readdressing the unit. However, no two (2) addresses can be the same. For example:

Pelco-P addresses above 32 are repeated in multiples of 32 (1, 33, 65, 97 are the same). Pelco-D addresses above 254 are repeated in multiples of 254 (1, 255, 509, 763 are the same).

To set FastAddress with a Pelco Keyboard:

1.Press and hold 95-PRESETfor two seconds to open the Pelco Setup menu.

2.Move the joystick to select the Command Lock menu.

3.Press the FOCUS or the IRIS button to turn Command Lock to OFF.

4.Move to the FastAddress menu and press the FOCUS button or the IRIS button to open the menu.

Bosch Security Systems, Inc.

Installation Manual

F.01U.249.416 2.0 2012.09

Page 34 Page 36
Image 35
Page 34 Page 36
Contents MIC612 Thermal Camera Page Table of Contents On-Screen Display OSD Menus Pelco Protocol Common User CommandsAdvanced Features On-Screen Display OSD Menus Bosch ProtocolIndex Maintenance and Troubleshooting Keyboard Commands By NumberConventions in this Manual SafetyImportant Safety Instructions About this ManualMIC612 Thermal Camera Safety en Important Notices EC DirectivesCoax grounding Informations FCC ET Ices applications commerciales FCC and Ices ComplianceFCC ET Ices Information commercial applications USA Customer Support and ServiceBosch Notices Additional Tools Required Parts List2Unpacking Additional Products RequiredMIC camera mounting positions Upright, Inverted Installation OverviewNumber Description Typical Mounting ArrangementsMounting Positions 3About the MIC Shielded Composite Cable About Alarm Inputs and OutputsAn 8-input alarm card installed in the MIC PSU Alarm Card Number Installed? Alarm Inputs Alarm OutputsMIC-BP4 sold separately InstallationTypical Installation Configurations Follow these steps in sequence to install the MIC612 camera Overview of Installation StepsExample 2 Configuration with RS-485 protocol connection Mounting the Camera Installing the MIC Power Supply Unit PSU Fuse Ratings Earth Link on PCB3Layout of MIC Power Supply Units PSUs for MIC612 Electrical Shock Hazard 4Installation InstructionsNumber Description PCB Marking Description AUX2 Number Description Cable Gland SizeAUX1 MIC612 Thermal Camera Installation en LED Description Power supply. Follow these stepsDisconnect the power supply from the power source Commissioning the Camera with Heater Option FittedScrewdriver Fitting the Optional Sunshield MIC612Bottom half of the sunshield see step Head is facing upEstablishing Control of the Camera via RS-485 Protocol Establishing Control of the Camera via Biphase ProtocolGetting Started Establishing Control of the CameraLCD Powering OnControlling the Camera Basic Keyboard OperationNavigating the On-Screen Display OSD Menus Keyboard Commands, Bosch Protocol4Keyboard Commands, Pelco Protocol Preset 4Setting the Addresses of the Two Cameras of the MIC612Special Preset Commands, Pelco Protocol FastAddress, Bosch Protocol Setting the Address of the Optical Camera via FastAddressTo set FastAddress with a Pelco Keyboard 3FastAddress, Pelco ProtocolsTo set an address for a camera without an address To change or clear an address for a camera with an addressSpecial Passwords Setting PasswordsConfiguring the Camera for Inverted Operation Active Commands in FastAddress6On-Screen Display OSD Menus Bosch Protocol Setup MenuATW Camera Setup MenuWDR Thermal Camera Setup Menu Manual Lens Setup MenuPTZ Setup Menu Display Setup Menu Compass Display AdjustCamera OSD AzimuthBaud Rate Communication Setup MenuCommunication Setup AutoBaudNone Alarm SetupOSD Outputs Setup SubmenuOutputs Setup Submenu Choices OutputsRule # Choices Enabled Rule Setup SubmenuRule Setup Rule Setup Submenu ChoicesOutput Language MenuInput Bist Diagnostics MenuInternal Humidity Security AccessCtfid Access Power Up EventsTotal Time On Alarm Status SubmenuAlarm Input Alarm OutputOn-Screen Display OSD Menus Pelco Protocol Continuous Camera SetupPelco menu Bosch menu Setup Menu Bosch MenuBalance PTZ SetupWhite OutdoorOFF Other MenusFlat-Field Correction FFC Switching VideoDisplaying Thermal Camera Temperature Operation of the Thermal CameraSet the Alarm Rule Triggering Alarms On Detection of Objects Outside of SetThermal Temperature Threshold Set the Temperature ThresholdSpecifying a Shot or a Sector Title Common User CommandsSetting AutoPan Mode Setting Preset ShotsProgramming the Inactivity Operation Configuring Preposition ToursRecording Tours Using the Wiper/Washer10.1.2 Alarm Rule Examples Advanced Features10.1 Alarm Rules 10.1.1 Controlling Alarm Rules10.2 Privacy Masking Example 2 Advanced Alarm Rule10.5 Azimuth, Elevation, and Compass Directions 10.5.1 Setting the Azimuth Zero Point10.3 Image Stabilization 10.4 Pre-position Tour180 / -45 S 10.5.2 Displaying Azimuth, Elevation, and Compass HeadingsProblem Explanation Solution 11Maintenance and TroubleshootingCommands, Optical Camera Keyboard Commands By NumberKeyboard Commands Bosch Protocol Refer to .5 Azimuth, Elevation, Compass Directions, Zone/Sector Title Menu Enters the Zone Title menu. Refer toCommands, Thermal Camera 70 en MIC612 Thermal Camera Keyboard User Action Description Command Keyboard Commands Pelco ProtocolEn MIC612 Thermal Camera Pre-compensation 39 sharpness 38 shutter White balance Index#-ENTER En Index MIC612 Thermal Camera Constant focus 41 manual focus 41 spot focus PTZ Custom tourZero pan ShotPage Page Bosch Security Systems, Inc

MIC612 specifications

The Bosch Appliances MIC612 is an innovative and highly efficient piece of kitchen equipment that enhances the culinary experience for home chefs and professionals alike. Renowned for its quality, Bosch has developed this compact microwave that combines advanced technology with user-friendly features.

One of the standout characteristics of the MIC612 is its sleek design, seamlessly incorporating into various kitchen styles. With its stainless-steel finish, the microwave not only offers aesthetic appeal but also ensures durability and easy maintenance. Its compact size makes it an ideal fit for smaller kitchens or areas where space is limited, while still providing ample cooking capacity.

The MIC612 is equipped with intelligent cooking technology. This includes sensor cooking, which automatically adjusts cooking time and power levels based on moisture detected in the food. This feature simplifies meal preparation by eliminating the need for constant monitoring, ensuring perfectly cooked dishes every time. Additionally, the microwave offers multiple cooking modes, including reheating, defrosting, and cooking with precision.

For those who appreciate convenience, the MIC612 includes pre-programmed settings for common foods like popcorn, pizza, and baked goods. This allows users to enjoy a wide variety of meals with minimal effort. The intuitive control panel and clear digital display enhance the ease of use, enabling quick selection of settings and cooking times.

Safety is a paramount concern for Bosch, and the MIC612 does not disappoint. It features a child safety lock, ensuring that curious little hands cannot accidentally operate the appliance. Moreover, the design incorporates a reliable cooling system to prevent overheating and ensure longevity.

Energy efficiency is another highlight of the Bosch MIC612. It is designed to consume less power compared to traditional microwaves, making it an eco-friendly choice without compromising performance. The combination of cutting-edge technology, thoughtful design, and practical features makes the Bosch Appliances MIC612 a valuable addition to any kitchen, offering versatility and reliability for all cooking needs. Whether reheating leftovers or preparing a fresh meal from scratch, this microwave stands out as a remarkable option for modern culinary tasks.
Top Page Image Contents