Bosch Power Tools 2000 4.0Receiver, 4.1Modem Reports, Rcvr Format, Series Program Entry Guide

Page 15
Receiver

2000 Series Program Entry Guide 4.0

Receiver

 

 

EN 15

4.0Receiver

4.1Modem Reports

1 Rcvr Format

Default:

Modem

 

 

 

Selection:

Modem, Pulse

 

 

 

0

 

Pulse

 

 

 

1

 

Modem

 

 

 

Set Rcvr Format to Modem to transmit reports in Modem II format with its advanced reporting capabilities.

You need firmware revision 8.00 or greater installed in your D6500 Receiver.

Table 2 shows the reports available.

The D6500 line card ack tone table must contain “Modem II for D9112.” Refer to the 6500: Line Program Entry Guide.

Set Rcvr Format to Pulse to transmit in 4x2 Pulse Format. Be sure to program codes for each report group. Refer to the Section 4.2 Pulse Report Groups.

Table 2: Modem II Reports Chart

 

Modem II Report

Description

 

AC FAILURE

 

No AC power to system. Control panel runs on battery.

 

AC RESTORE

AC Power is restored to normal.

 

 

 

 

ALARM REPORT POINT

Alarm Report from Points 1 to 24 or from an A, B, C, key. Refer to Section 7.0 ABC Keys for

001 (-099)

 

instructions on setting reports from the keys.

 

ALARM REPORT

If an alarm occurs within 2 minutes of a Closing event, the system sends an Alarm Recent

 

RECENT CLOSING

Close Report.

 

ID=001

 

 

POINT=001(24)

 

 

 

 

 

ALARM CROSS POINT

 

Alarm Report from Points 1 to 24 with point code for Cross or Partner point.

 

001 (-099)

 

The ALARM RECENT CLOSE message overrides the ALARM CROSS POINT message.

 

 

 

The ALARM EXIT ERROR message does not apply to Cross, Partner, Double Knock, or Alarm

 

 

 

Verification points

 

BATTERY LOW

System battery is low.

 

 

 

 

BATTERY MISSING

 

System battery is disconnected. Battery must be missing for 60 seconds.

 

BATTERY RESTORE

Missing or low battery is restored.

 

 

 

 

CANCEL REPORT

 

Cancel Report from keyswitch.

 

CANCEL REPORT ID

Cancel Report with user ID for users 1 to 8.

001 (-008)

 

 

 

 

 

 

 

 

 

 

Bosch Security Systems 7/05 35114F

Image 15
Contents 2000 Series Control PanelsBosch Security Systems 7/05 35114F Using this Guide for Keypad ProgrammingAbout This Manual E Version Control PanelsBosch Security Systems 7/05 35114F Contents2000 Series Program Entry Guide Contents An Example, Entering Custom TextFigures Tables2000 Series Program Entry Guide Contents 2000 Series Program Entry Guide 1.0 System ConfigurationSystem Configuration 3 Keyswitch2000 Series Program Entry Guide 6 Custom Service TextSystem Configuration Default BlankPhone 2.0 Phone2.1Phone Routing Set to No Phone Routing Set to Yes8 Restoral Route 5 Fire Route6 Non-FireRoute 7 Pt Trbl Route14 Duress Route 11 Cancel Route12 Sys Trbl Route 13 Sys Trbl RoutePhone 15 Test RouteDefault: Local 2000 Series Program Entry Guide3 Restricted O/C 3.0 ReportsReports 1 O/C Rpts - All On2000 Series Program Entry Guide 5 Cancel Rpt6 Restoral Rpts 7 AC Fail Buzz/RptReports 8 Point User FlagDefault 2000 Series Program Entry GuideBosch Security Systems | 7/05 | 35114F 2000 Series Program Entry GuideReports EN1 Rcvr Format 4.0Receiver4.1Modem Reports ReceiverTable 2 continued 2000 Series Program Entry GuideReceiver ENTable 2 continued 2000 Series Program Entry GuideReceiver EN2 Fire Group 4.2Pulse Report Groups1 - Account number 2 - Report group 3 - Point, user5 Restoral Group 8 Cancel Group3 Non-FireGroup 4 Pt Trbl Group2000 Series Program Entry Guide 10 Sys Res Group11 Duress Group 12 Test Group2 RAM Phone 5.0 Remote ProgrammingRemote Programming 1 RAM Passcode2000 Series Program Entry Guide Remote ProgrammingEN 2 Exit Dly Time 6.0 Open/CloseOpen/Close 1 Entry Dly Time2000 Series Program Entry Guide 6.1Step Outside5 No Delay 6 Excursion6.2Exit 2000 Series Program Entry GuideOpen/Close Bosch Security Systems 7/05 35114F 2000 Series Program Entry GuideOpen/Close EN1 A-KeyReport 2 A-KeyAlarm Output7.0ABC Keys ABC Keys10 C-KeyOutput 5B-KeyAlarm Report 6 B-KeyOutput 7 B-KeyAck Tone9 C-KeyAlarm Report 8 B-KeyText1 Bell Time 4 Alarm on 2 Fail8.0 Bell BellBosch Security Systems 7/05 35114F 2000 Series Program Entry GuideBell EN2 Hours to Next 9.0 Test TimerTest Timer 1 Test IntervalTest Timer 2000 Series Program Entry GuideThe report defers one interval from the time of the last report. For example, if theTest Intrvl prompt is set to 1 Day, and the system transmits an Opening Report at 9 00 PM, the interval begins at 9 00 PM. If the system transmitted no other reports before 9 00 PM the following day, at 9 00 PM the system transmits the Test Report 6 Address 7 Address 8 Address 10.0 Address ConfigurationAddress Configuration 1 Address 2 Address 3 Address 4 Address 5 AddressBosch Security Systems 7/05 35114F Address Configuration2000 Series Program Entry Guide EN2 Point 11.0 Point CodesPoint Codes 1 Point7 to 24 Points 7 to 4 Point5 Point 6 PointPoint Codes 11.1Digit 1, Point TypeRefer to Section 11.3 Digit 3, Point Options 2000 Series Program Entry GuideEN 11.3 Digit 3, Point Options2000 Series Program Entry Guide Point Codes2000 Series Program Entry Guide Point CodesEN 2000 Series Program Entry Guide Point CodesEN 2000 Series | Program Entry Guide | Point CodesEN EN the Extended Delay feature2000 Series Program Entry Guide Point Codes11.2Digit 2, Alarm Responses 2000 Series Program Entry GuidePoint Codes EN 11.3Digit 3, Point Options2000 Series Program Entry Guide Point CodesEN 11.4Digit 4, Device Address2000 Series Program Entry Guide Point Codes11.5Digit 5, Sensor Loop 2000 Series Program Entry GuidePoint Codes Table 9 Digit Selection Summary 2000 Series Program Entry GuidePoint Codes EN11.6 Recommended Point Codes 2000 Series Program Entry GuidePoint Codes 2000 Series Program Entry Guide Point CodesTable 16 Panic Device swinger bypass Bosch Security Systems 7/05 35114F 2000 Series Program Entry GuidePoint Codes EN2000 Series Program Entry Guide 12.0 Point TextPoint Text 1 to 24 Point TextBosch Security Systems 7/05 35114F 2000 Series Program Entry GuidePoint Text ENRelays 13.0 Relays13.1Relay Function Logic 13.2Relay FunctionsEN the Parameter prompt2000 Series Program Entry Guide Relays2000 Series Program Entry Guide RelaysEN 13.3Relay Parameters, for Keypad Programming Only 2000 Series Program Entry GuideRelays 1 User Tst, Bell 2 User Tst, Battery14.0 User Test User TestBosch Security Systems 7/05 35114F 2000 Series Program Entry GuideUser Test EN2 Passcode Length 15.0 PasscodesPasscodes 1 Instir Codepasscode for up to eight users 5 Change PasscodePasscode-# the Passcode Type and to enter a unique2000 Series Program Entry Guide 16.0 RF ParametersRF Parameters 1 Supervision IntervalBosch Security Systems 7/05 35114F 2000 Series Program Entry GuideRF Parameters ENProgram Lock 1 Return to Default3 Disable System 17.0 Program LockBosch Security Systems 7/05 35114F 2000 Series Program Entry GuideProgram Lock ENKeypad Programming 18.0Keypad Programming18.1Getting Started 18.2View Mode18.4 Scroll Lists 18.3Modify Mode18.4Scroll Lists 18.5Yes and No Entries18.6An Example, Entering Custom Text 2000 Series Program Entry GuideKeypad Programming 18.7Keypad Programming Tips 2000 Series Program Entry GuideKeypad Programming 2000 Series Program Entry Guide Index Index2000 Series Program Entry Guide Index 2000 Series Program Entry Guide Index 2005 Bosch Security Systems 35114F Fairport, NY Customer ServiceBosch Security Systems 130 Perinton Parkway Technical Support