Bosch Power Tools 2000 manual User Test, User Tst, Bell, User Tst, Comm, User Tst, Battery

Page 57
User Test

2000 Series Program Entry Guide 14.0

User Test

 

 

EN 57

14.0 User Test

If the user presses [1] at the keypad and then enters their passcode, the system performs a user test. Prompts 1 to 3 tell the system what functions to perform for the User Test.

1 User Tst, Bell

Default:

No

 

 

Selection:

Yes, No

 

 

0

No

 

 

1

Yes

 

 

Setting the Usr Tst, Bell prompt to Yes makes a Bell Test part of the User Test. The system activates the Alarm Output (Terminals 4 and 5) for 3 seconds. Light 1 on the keypad flashes for the duration of the test.

Set this prompt to Yes for UL 1023,

Household Fire systems.

3 User Tst, Comm

Default:

 

No

 

 

Selection:

 

 

Yes, No

 

 

 

 

 

 

 

 

 

 

 

0

 

 

No

 

 

 

1

 

Yes

 

 

 

 

 

 

Setting the Usr Tst, Comm prompt to Yes makes a Communication Test part of the User Test. When the user presses [1] and enters a passcode, the system sends a Test Report to the receiver. Light 1 flashes during the test. If the system fails to communicate with the receiver, the system goes into communication failure and displays a system trouble at the keypad by flashing the OK light. Refer to Check System in the User Guide.

The system makes five attempts to send the report if only one phone number is programmed. It makes ten attempts if two numbers are programmed. Refer to Phone 1, Phone 2 , in Section 2.0 Phone.

2 User Tst, Battery

Default:

No

Selection:

Yes, No

 

 

0

No

 

 

1

Yes

 

 

Setting the Usr Tst, Battery prompt to Yes makes a Battery Test part of the User Test. Pressing [1] causes the system to run solely on battery power for 4 minutes. Light 1 flashes while the control panel is on battery power. If the battery voltage falls below 12.1 VDC during that 4 minutes, the system restores AC power and displays a system trouble at the keypad by flashing the OK light. Refer to System Troubles in the User Guide.

The system sends a Low Battery Report to the receiver.

Users can end the test by pressing the [CLEAR] key.

Set this prompt to Yes for UL 1023,

Household Fire systems.

Bosch Security Systems 7/05 35114F

Image 57
Contents 2000 Series Control PanelsAbout This Manual Using this Guide for Keypad ProgrammingE Version Control Panels Bosch Security Systems 7/05 35114F2000 Series Program Entry Guide Contents ContentsAn Example, Entering Custom Text Bosch Security Systems 7/05 35114FFigures Tables2000 Series Program Entry Guide Contents System Configuration 1.0 System Configuration3 Keyswitch 2000 Series Program Entry GuideSystem Configuration 6 Custom Service TextDefault Blank 2000 Series Program Entry Guide2.1Phone Routing Set to No 2.0 PhonePhone Routing Set to Yes Phone6 Non-FireRoute 5 Fire Route7 Pt Trbl Route 8 Restoral Route12 Sys Trbl Route 11 Cancel Route13 Sys Trbl Route 14 Duress RouteDefault: Local 15 Test Route2000 Series Program Entry Guide PhoneReports 3.0 Reports1 O/C Rpts - All On 3 Restricted O/C6 Restoral Rpts 5 Cancel Rpt7 AC Fail Buzz/Rpt 2000 Series Program Entry GuideDefault 8 Point User Flag2000 Series Program Entry Guide ReportsReports 2000 Series Program Entry GuideEN Bosch Security Systems | 7/05 | 35114F4.1Modem Reports 4.0ReceiverReceiver 1 Rcvr FormatReceiver 2000 Series Program Entry GuideEN Table 2 continuedReceiver 2000 Series Program Entry GuideEN Table 2 continued1 - Account number 2 - Report group 4.2Pulse Report Groups3 - Point, user 2 Fire Group3 Non-FireGroup 8 Cancel Group4 Pt Trbl Group 5 Restoral Group11 Duress Group 10 Sys Res Group12 Test Group 2000 Series Program Entry GuideRemote Programming 5.0 Remote Programming1 RAM Passcode 2 RAM Phone2000 Series Program Entry Guide Remote ProgrammingEN Open/Close 6.0 Open/Close1 Entry Dly Time 2 Exit Dly Time5 No Delay 6.1Step Outside6 Excursion 2000 Series Program Entry Guide6.2Exit 2000 Series Program Entry GuideOpen/Close Open/Close 2000 Series Program Entry GuideEN Bosch Security Systems 7/05 35114F7.0ABC Keys 2 A-KeyAlarm OutputABC Keys 1 A-KeyReport9 C-KeyAlarm Report 5B-KeyAlarm Report 6 B-KeyOutput 7 B-KeyAck Tone8 B-KeyText 10 C-KeyOutput8.0 Bell 4 Alarm on 2 FailBell 1 Bell TimeBell 2000 Series Program Entry GuideEN Bosch Security Systems 7/05 35114FTest Timer 9.0 Test Timer1 Test Interval 2 Hours to NextTest Timer 2000 Series Program Entry GuideThe report defers one interval from the time of the last report. For example, if theTest Intrvl prompt is set to 1 Day, and the system transmits an Opening Report at 9 00 PM, the interval begins at 9 00 PM. If the system transmitted no other reports before 9 00 PM the following day, at 9 00 PM the system transmits the Test Report Address Configuration 10.0 Address Configuration1 Address 2 Address 3 Address 4 Address 5 Address 6 Address 7 Address 8 Address2000 Series Program Entry Guide Address ConfigurationEN Bosch Security Systems 7/05 35114FPoint Codes 11.0 Point Codes1 Point 2 Point5 Point 4 Point6 Point 7 to 24 Points 7 toRefer to Section 11.3 Digit 3, Point Options 11.1Digit 1, Point Type2000 Series Program Entry Guide Point Codes2000 Series Program Entry Guide 11.3 Digit 3, Point OptionsPoint Codes EN2000 Series Program Entry Guide Point CodesEN 2000 Series Program Entry Guide Point CodesEN 2000 Series | Program Entry Guide | Point CodesEN 2000 Series Program Entry Guide the Extended Delay featurePoint Codes EN11.2Digit 2, Alarm Responses 2000 Series Program Entry GuidePoint Codes 2000 Series Program Entry Guide 11.3Digit 3, Point OptionsPoint Codes EN2000 Series Program Entry Guide 11.4Digit 4, Device AddressPoint Codes EN11.5Digit 5, Sensor Loop 2000 Series Program Entry GuidePoint Codes Point Codes 2000 Series Program Entry GuideEN Table 9 Digit Selection Summary11.6 Recommended Point Codes 2000 Series Program Entry GuidePoint Codes 2000 Series Program Entry Guide Point CodesTable 16 Panic Device swinger bypass Point Codes 2000 Series Program Entry GuideEN Bosch Security Systems 7/05 35114FPoint Text 12.0 Point Text1 to 24 Point Text 2000 Series Program Entry GuidePoint Text 2000 Series Program Entry GuideEN Bosch Security Systems 7/05 35114F13.1Relay Function Logic 13.0 Relays13.2Relay Functions Relays2000 Series Program Entry Guide the Parameter promptRelays EN2000 Series Program Entry Guide RelaysEN 13.3Relay Parameters, for Keypad Programming Only 2000 Series Program Entry GuideRelays 14.0 User Test 2 User Tst, BatteryUser Test 1 User Tst, BellUser Test 2000 Series Program Entry GuideEN Bosch Security Systems 7/05 35114FPasscodes 15.0 Passcodes1 Instir Code 2 Passcode LengthPasscode-# 5 Change Passcodethe Passcode Type and to enter a unique passcode for up to eight usersRF Parameters 16.0 RF Parameters1 Supervision Interval 2000 Series Program Entry GuideRF Parameters 2000 Series Program Entry GuideEN Bosch Security Systems 7/05 35114F3 Disable System 1 Return to Default17.0 Program Lock Program LockProgram Lock 2000 Series Program Entry GuideEN Bosch Security Systems 7/05 35114F18.1Getting Started 18.0Keypad Programming18.2View Mode Keypad Programming18.4Scroll Lists 18.3Modify Mode18.5Yes and No Entries 18.4 Scroll Lists18.6An Example, Entering Custom Text 2000 Series Program Entry GuideKeypad Programming 18.7Keypad Programming Tips 2000 Series Program Entry GuideKeypad Programming 2000 Series Program Entry Guide Index Index2000 Series Program Entry Guide Index 2000 Series Program Entry Guide Index Bosch Security Systems 130 Perinton Parkway Fairport, NY Customer ServiceTechnical Support 2005 Bosch Security Systems 35114F