BEFORE LIGHTING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES
A. This appliance has.a .pi.Iotwhich is lit.by a piezo- elec_ncsparKgas j,gnluonsystem, uo n_.gqpen.o _neinner aoor of me appliance and _ry_oIIgh_ the pilot by hand.
B.BEFORE LIGHTINGsmell aII around the appliance area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS oDo not try to light any appliance.
*Do not touch any electric switch; do not use any phone in your building.
elmmediately call your gas supplier from a neighbor's
*If you cannot reach your gas supplier, call the fire department.
C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob wilt not push in or turn by hand, don'ttry to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately contact a qualified installer or service agency to replace a flooded water heater. Do not attempt to repair the unit! It must be replaced!
phone. Follow the gas supptier'sinstructions.
FIGURE W | FIGURE 'B' | FIGURE 'C' | |||
120°F | C | ..,. | 120°F | C | |
Mi;' |
|
|
|
| |
LOW |
|
| LOW |
|
|
HO_ |
|
| HUr_ |
|
|
"OFF" POSITION | "PILOT" | POSITION | "ON" POSITION | ||
|
|
|
|
|
MAINBURNER_
"PILOT !
--Igniter GASCONTROL
CONTROL
KNOB
FIGURE 'D'
.STOP!It is imyou readall safety lightingthe pilot.
2.Turnthe gascontrol/temperatureknob counterclockwise_to the "OFF"setting.
3.Waitten (10)minutesto clearout any gas. Ifyou then
smell gas, STOP._Follow B in the safety
informationabove,on thislabel.If youdo not smellgas,goto the nextstep.
4.Turnthe gascontrol/temperatureknobclockwise¢to" PILOT".SeeFigure'B'.
5.Pressthe gas control/temperature knob all the way in and hold it in. The knob should travel in about
1/4 inch (6.35 mm) if it is set to "PILOT" correctly. While holdinq the qas control/temperature knob in, click the iqniter button continuously (about once a second) for up to 90 seconds or until Status Liqht beqins to blink.
6.Whenthestatuslightstartsblinking,releasethe gas control/temperatureknob. Setthe gascontrol/ temperatureknobto the desiredsetting.SeeFigure'C'.
If the status light does not start blinking within 90 seconds, repeat steps 2 through 5 up to THREE
(3)times, waiting 10 minutes between lighting attempts.
The circuitry in this advancedqas valve requires that you wait 10 minutes between liqhtinq attempts.
Ifthe statuslight turnssolid red, releasethe gas control/temperatureknoband repeatsteps2 through
5(waiting10minutesbeforeattemptingto relightthe pilot).
Ifthestatuslightdoesnotstart blinkingafterthree lightingattempts,turnthe gascontrol/temperatureknob to "OFF"and calla qualifiedservicetechnicianor your gassupplier.
_Hotter waterincreasestheriskof scald
injury. Consultthe instruction manualbefore changing temperature.
Refertothe UghtingInstructionsinthe Installation
Manualfor moredetailedtroubleshooting information.
1.Turnthegascontrolltemperatureknobcounterclockwise€to the"OFF"setting.Thestatuslightwillstopblinkingandstay onforashorttimeafterthewaterheateristurnedoff.SeeFigure'A'.
24