New Buck Corporation manual SECTION INSTALLATION OF MODEL 384 WS WITH

Page 26

SECTION IV

SECTION IV

INSTALLATION OF MODEL 384 (WS) WITH

OPTIONAL WOODEN SURROUND (KIT#PAKDM384)

NOTE: See page 20 for clearances.

(1)When choosing the right location for your heater and wooden surround keep the following in mind:

NOTE: Due to high temperatures, this heater should be located out of traffic areas and away from furniture and draperies.

CAUTION: THE INSTALLATION MUST CONFORM TO LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, INSTALLATION MUST CONFORM WITH THE NATIONAL GAS CODES.

NOTE: See Section II for gas hookup and pressure check.

NOTE: See “Producing Adequate Ventilation” page 31.

(2)Position screen before leaving heater unattended.

(3)Instructions for assembly of Wooden Surround (Mantel):

TOOLS NEEDED: Medium Phillips screwdriver, tape measure, power drill, and 5/16" socket.

STEP 1: Lay out all components.

STEP 2: Assemble end panels A & B to top front rail C.

STEP 3: Stand end panels and top front rail onto hearth.

NOTE: (Position back of end panels with back of hearth centering assembly from each end). Install front screws first, then pull back towards the inside to square the mantel. Install screws through back holes.

STEP 4: The owner must decide at this time if parts D, E, and F are to be wood or green. Beginning with panel E stand chosen color face out on hearth flush against stop block located inside end panel A and attach. Position the left end of top window D on top of E and attach. Slide panel F under the right end of D and attach.

STEP 5: Place a cloth or blanket over the front portions of mantel as not to scar the wooden part of the mantel.

The Manufacturers Trim Kit must be used for Wooden Surround Installation.

1.Set the top (long) trim panel in place on top of unit. The panel should be flat against the outside face of the fireplace, and standing vertically (measuring approximately 12” from the rear of the unit to the front area). Mark along the lower edge of the trim panel with a pencil to make reference line for mounting.

2.Set the side panels in place, flat against the fireplace. Mark down the inside edge of the trim panel to make a vertical reference line.

Page 22

Image 26

Contents Manufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South MODELVENT-FREE Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS 6. What To Do IF You Smell Gas Shut off gas supply 32. This appliance is intended for supplemental heating SECTION FIREPLACE PREPARATIONFLAME INSTALLATION AND CLEARANCESGAS CONNECTION Page “MILLIVOLT ONLY” GAS PRESSURE CHECK FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTION MODULATING OR MANUAL VALVE SITLIGHTING INSTRUCTION to “ON” position. Continue to turn the to your desired setting 12. Close access panel door13. Turn on all electrical power to the appliance MANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONOPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS SIT-MILLIVOLT VALVE Page Page MANUAL LIGHTING PROCEDURE CR 3329 LOG SET WHEN USED AS A HEATING APPLIANCE HEAT OUTPUTFLAME CHECK WIRING DIAGRAM NOTE #PE SBR084 Blower Motor Rating 120 volts/60HZ/1.1 Amps CEILING SECTION INSTALLATION MODEL 384 FP IN SOLID FUEL BURNING FIREPLACESTrim Kit Also provide adequate clearances around air openings SECTION INSTALLATION OF MODEL 384 WS WITH OPTIONAL WOODEN SURROUND KIT#PAKDM384STEP 7 Remove cloth or blanket from underneath stove GAS LINE SECTION ZERO CLEARANCE INSTALLATION OF MODEL 384 ZCCHOOSING THE LOCATION FOR YOUR FIREPLACE DRAFTSTop Standoff 2 per unit ZERO CLEARANCE STANDOFFS ASSEMBLY“Follow the instructions given in the diagrams below exactly” 12.50” Front Of Top Trim PanelInstall the Firebox INSTALLING THE FIREBOXFIREPLACE CLEARANCES Framing the FireboxFINISHING YOUR FIREPLACE CLEARANCESSECTION MODEL 384 FS FREESTANDING INSTALLATION FREESTANDING PEDESTAL OR LEGS INSTALLATION SECTION MODEL ALCOVE INSTALLATION CAUTION READ ENTIRE MANUAL BEFORE INSTALLING HEATERThis section is for residential or manufactured mobile installation SECTION PRODUCING ADEQUATE VENTILATIONDETERMINING FRESH-AIR FLOW FOR HEATER LOCATION 1. Determine the volume of the space length x width x height SECTION VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDINGVENTILATION AIR FROM OUTDOORS Ventilation Air From OutdoorsSECTION AFTER MARKET MOBILE HOME INSTALLATION IMPORTANT SAFEGUARDS CLEANINGOBSERVED Air in gas lines when OBSERVED OBSERVED REPAIR PARTS SERVICINGKEY# REPLACEMENT PARTSSIT MODULATING OR MANUAL VALVE PART DESCRIPTION1719 PILOTREPLACEMENT PARTS SIT MILLIVOLT VALVESIT MILLIVOLT REPLACEMENT PARTS FOR EMBER STOVE BASE ESB SIT MILLIVOLT 10 one is not available, you may contactPage LIMITED WARRANTY VENT-FREE GAS LOG HEATER NEW BUCK CORPORATIONPage