New Buck Corporation manual SECTION MODEL 384 FS FREESTANDING INSTALLATION

Page 32

SECTION VI

SECTION VI

MODEL 384 (FS)

FREESTANDING INSTALLATION

(1) Determine the exact position of your gas heater.

NOTE: Due to high temperatures, this heater should be located out of traffic areas and away from furniture and draperies.

NOTE: For safe installation the minimum clearances must be met. See Figure below.

			CEILING	0"
			CEILING
REAR WALL			26"26"
NOTE:			26"26"
NOTE:
DIMENSIONS SHOWN ARE
MINIMUM CLEARANCE TO	0"2”
7” COMBUSTIBLE WALL.	0"2”	Figure 10		REARWALL
7"	7"	Figure 10		REARWALL
7"
STOVE
FACING UNIT
LEFT	RIGHT		SIDE VIEW
WALL	WALL

WALL

2”

0"2”

WALLCORNER INSTALLATIO

CAUTION: The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA54.

NOTE: See page 5 for Gas Connection and Pressure Check.

(2)Make sure you have the right valve for your type of gas. Check label on side of valve. Position logs as shown in Log Placement Section, Pages 6-7. Position screen before leaving heater unat- tended.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

Page 28

Image 32

Contents MODEL VENT-FREEManufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS 6. What To Do IF You Smell Gas Shut off gas supply 32. This appliance is intended for supplemental heating SECTION FIREPLACE PREPARATIONFLAME INSTALLATION AND CLEARANCESGAS CONNECTION Page “MILLIVOLT ONLY” GAS PRESSURE CHECK FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTION MODULATING OR MANUAL VALVE SITLIGHTING INSTRUCTION to “ON” position. Continue to turn the to your desired setting 12. Close access panel door13. Turn on all electrical power to the appliance MANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONOPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS SIT-MILLIVOLT VALVE Page Page MANUAL LIGHTING PROCEDURE CR 3329 LOG SET WHEN USED AS A HEATING APPLIANCE HEAT OUTPUTFLAME CHECK WIRING DIAGRAM NOTE #PE SBR084 Blower Motor Rating 120 volts/60HZ/1.1 Amps CEILING SECTION INSTALLATION MODEL 384 FP IN SOLID FUEL BURNING FIREPLACESTrim Kit Also provide adequate clearances around air openings SECTION INSTALLATION OF MODEL 384 WS WITH OPTIONAL WOODEN SURROUND KIT#PAKDM384STEP 7 Remove cloth or blanket from underneath stove SECTION ZERO CLEARANCE INSTALLATION OF MODEL 384 ZC CHOOSING THE LOCATION FOR YOUR FIREPLACEGAS LINE DRAFTSZERO CLEARANCE STANDOFFS ASSEMBLY “Follow the instructions given in the diagrams below exactly”Top Standoff 2 per unit 12.50” Front Of Top Trim PanelINSTALLING THE FIREBOX FIREPLACE CLEARANCESInstall the Firebox Framing the FireboxFINISHING YOUR FIREPLACE CLEARANCESSECTION MODEL 384 FS FREESTANDING INSTALLATION FREESTANDING PEDESTAL OR LEGS INSTALLATION SECTION MODEL ALCOVE INSTALLATION CAUTION READ ENTIRE MANUAL BEFORE INSTALLING HEATERThis section is for residential or manufactured mobile installation SECTION PRODUCING ADEQUATE VENTILATIONDETERMINING FRESH-AIR FLOW FOR HEATER LOCATION 1. Determine the volume of the space length x width x height SECTION VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDINGVENTILATION AIR FROM OUTDOORS Ventilation Air From OutdoorsSECTION AFTER MARKET MOBILE HOME INSTALLATION IMPORTANT SAFEGUARDS CLEANINGOBSERVED Air in gas lines when OBSERVED OBSERVED REPAIR PARTS SERVICINGREPLACEMENT PARTS SIT MODULATING OR MANUAL VALVEKEY# PART DESCRIPTION1719 PILOTREPLACEMENT PARTS SIT MILLIVOLT VALVESIT MILLIVOLT REPLACEMENT PARTS FOR EMBER STOVE BASE ESB SIT MILLIVOLT 10 one is not available, you may contactPage LIMITED WARRANTY VENT-FREE GAS LOG HEATER NEW BUCK CORPORATIONPage