New Buck Corporation 384 manual Table Of Contents

Page 3

TABLE OF CONTENTS
SECTION I: Safety Information	1
SECTION II: Fireplace Preparation	4
Fireplace Clearances	5
Gas Connection	5
Placement of Logs	6
Gas Pressure Check	8
Lighting Instructions - SIT Modulating or SIT Manual……………………………...9
Lighting Instructions - SIT Millivolt Valve	13
Flame Check	17
Heat Output	17
Wiring Diagram	18
SECTION III: Solid Fuel Burning Fireplace Installation (FP)……….…………………20
SECTION IV: Wooden Surround Installation (WS)	22
SECTION V: Zero Clearance Installation (ZC)	24
SECTION VI: Freestanding Installation (FS)…………………………………………...28
SECTION VII: Alcove Installation……………….…………………………………...…30
SECTION VIII: Producing Adequate Ventilation	31
SECTION IX: Ventilation Air From Inside	33
SECTION X: Ventilation Air Outdoors	34
SECTION XI: After Market Mobile Home	35
Important Safeguards	36
Cleaning	36
Trouble Shooting	37
Service and Repair Parts	41
Replacement Parts	42
Warranty/Owner Registration	49

Image 3

Contents Spruce Pine, NC MODELVENT-FREE Manufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 SouthPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS 6. What To Do IF You Smell Gas Shut off gas supply 32. This appliance is intended for supplemental heating FIREPLACE PREPARATION SECTIONINSTALLATION AND CLEARANCES GAS CONNECTIONFLAME Page “MILLIVOLT ONLY” GAS PRESSURE CHECK LIGHTING INSTRUCTION MODULATING OR MANUAL VALVE SIT FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTION 12. Close access panel door 13. Turn on all electrical power to the applianceto “ON” position. Continue to turn the to your desired setting THERMOSTAT CONTROL OPERATION MANUAL LIGHTING PROCEDUREFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS SIT-MILLIVOLT VALVEOPERATING INSTRUCTIONS Page Page MANUAL LIGHTING PROCEDURE WHEN USED AS A HEATING APPLIANCE HEAT OUTPUT FLAME CHECKCR 3329 LOG SET WIRING DIAGRAM NOTE #PE SBR084 Blower Motor Rating 120 volts/60HZ/1.1 Amps SECTION INSTALLATION MODEL 384 FP IN SOLID FUEL BURNING FIREPLACES Trim KitCEILING Also provide adequate clearances around air openings OPTIONAL WOODEN SURROUND KIT#PAKDM384 SECTION INSTALLATION OF MODEL 384 WS WITHSTEP 7 Remove cloth or blanket from underneath stove DRAFTS SECTION ZERO CLEARANCE INSTALLATION OF MODEL 384 ZCCHOOSING THE LOCATION FOR YOUR FIREPLACE GAS LINE12.50” Front Of Top Trim Panel ZERO CLEARANCE STANDOFFS ASSEMBLY“Follow the instructions given in the diagrams below exactly” Top Standoff 2 per unitFraming the Firebox INSTALLING THE FIREBOXFIREPLACE CLEARANCES Install the FireboxCLEARANCES FINISHING YOUR FIREPLACESECTION MODEL 384 FS FREESTANDING INSTALLATION FREESTANDING PEDESTAL OR LEGS INSTALLATION CAUTION READ ENTIRE MANUAL BEFORE INSTALLING HEATER SECTION MODEL ALCOVE INSTALLATIONSECTION PRODUCING ADEQUATE VENTILATION DETERMINING FRESH-AIR FLOW FOR HEATER LOCATIONThis section is for residential or manufactured mobile installation 1. Determine the volume of the space length x width x height VENTILATION AIR FROM INSIDE BUILDING SECTION VENTILATION AIRVentilation Air From Outdoors VENTILATION AIR FROM OUTDOORSSECTION AFTER MARKET MOBILE HOME INSTALLATION CLEANING IMPORTANT SAFEGUARDSOBSERVED Air in gas lines when OBSERVED OBSERVED SERVICING REPAIR PARTSPART DESCRIPTION REPLACEMENT PARTSSIT MODULATING OR MANUAL VALVE KEY#PILOT 1719SIT MILLIVOLT VALVE REPLACEMENT PARTSSIT MILLIVOLT REPLACEMENT PARTS FOR EMBER STOVE BASE ESB 10 one is not available, you may contact SIT MILLIVOLTPage NEW BUCK CORPORATION LIMITED WARRANTY VENT-FREE GAS LOG HEATERPage