New Buck Corporation 384 manual Replacement Parts For Ember Stove Base Esb

Page 50

REPLACEMENT PARTS FOR

REPLACEMENT PARTS FOR

EMBER STOVE BASE (ESB)

(PICTURE ON PAGE 47)

A parts list with exploded view follows. Always include correct name, part number, and model number of the heater when ordering service parts.

KEY#	PART DESCRIPTION
	SIT - MILLIVOLT

1.O.D.S. PILOT (L.P.) O.P. ASSEMBLY

1.O.D.S. PILOT (NAT) O.P. ASSEMBLY

2.GENERATOR ASSEMBLY

3.PILOT TUBE 3/16"

4.GENERATOR WIRE

5.REAR BURNER FRONT BURNER

6.INLET ELBOW

7.3/8" COMP. NUT & SLEEVE

8.3/8" BURNER SUPPLY TUBE (FLEX)

-3 pieces 12"

9.24" SWITCH WIRES

10.CARLING SWITCH (AUTO/OFF/MANUAL)

11.PIEZO STRIKER

12.PIEZO 18" IGNITOR WIRE

13.MALE RUN TEE FITTING

14.THERMO-COUPLE

15.MANIFOLD OUTLET CONNECTOR

16.ORIFICES L.P.

FRONT #1.25mm

REAR #.046”

NATURAL

FRONT #2.05mm

REAR #48

17.820 mv. S.I.T. VALVE

18.8”L 3/8”BURNER SUPPLY LINE

(3/4”-3/8” FLARE/3/8” COMP. N&S FITTINGS)

PART NUMBER

PE 8404C

PE 8204C

(Part of Pilot Assembly) MF 31612 ALMTUB (Part of Pilot Assembly) PO VE1002

PO 383436

PH 4966

PH 616 & PH 606

PO T6-12

PE 30JUMPER

PE RC211RB

PE 124461

PE 8400-014

PH 64A-66

PH 68A-6C

PO 125 MVORF

PO 046 MVORF

PO 205 MVORF

PO 48 MVORF

LP - PE 820-636

NAT - PE 820-637

MF382ALMTUB

*

LOG SET

EMBER STOVE BASE (CERAMIC)

Page 46

Image 50

Contents Manufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South MODELVENT-FREE Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS 6. What To Do IF You Smell Gas Shut off gas supply 32. This appliance is intended for supplemental heating SECTION FIREPLACE PREPARATIONFLAME INSTALLATION AND CLEARANCESGAS CONNECTION Page “MILLIVOLT ONLY” GAS PRESSURE CHECK FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTION MODULATING OR MANUAL VALVE SITLIGHTING INSTRUCTION to “ON” position. Continue to turn the to your desired setting 12. Close access panel door13. Turn on all electrical power to the appliance MANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONOPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS SIT-MILLIVOLT VALVE Page Page MANUAL LIGHTING PROCEDURE CR 3329 LOG SET WHEN USED AS A HEATING APPLIANCE HEAT OUTPUTFLAME CHECK WIRING DIAGRAM NOTE #PE SBR084 Blower Motor Rating 120 volts/60HZ/1.1 Amps CEILING SECTION INSTALLATION MODEL 384 FP IN SOLID FUEL BURNING FIREPLACESTrim Kit Also provide adequate clearances around air openings SECTION INSTALLATION OF MODEL 384 WS WITH OPTIONAL WOODEN SURROUND KIT#PAKDM384STEP 7 Remove cloth or blanket from underneath stove GAS LINE SECTION ZERO CLEARANCE INSTALLATION OF MODEL 384 ZCCHOOSING THE LOCATION FOR YOUR FIREPLACE DRAFTSTop Standoff 2 per unit ZERO CLEARANCE STANDOFFS ASSEMBLY“Follow the instructions given in the diagrams below exactly” 12.50” Front Of Top Trim PanelInstall the Firebox INSTALLING THE FIREBOXFIREPLACE CLEARANCES Framing the FireboxFINISHING YOUR FIREPLACE CLEARANCESSECTION MODEL 384 FS FREESTANDING INSTALLATION FREESTANDING PEDESTAL OR LEGS INSTALLATION SECTION MODEL ALCOVE INSTALLATION CAUTION READ ENTIRE MANUAL BEFORE INSTALLING HEATERThis section is for residential or manufactured mobile installation SECTION PRODUCING ADEQUATE VENTILATIONDETERMINING FRESH-AIR FLOW FOR HEATER LOCATION 1. Determine the volume of the space length x width x height SECTION VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDINGVENTILATION AIR FROM OUTDOORS Ventilation Air From OutdoorsSECTION AFTER MARKET MOBILE HOME INSTALLATION IMPORTANT SAFEGUARDS CLEANINGOBSERVED Air in gas lines when OBSERVED OBSERVED REPAIR PARTS SERVICINGKEY# REPLACEMENT PARTSSIT MODULATING OR MANUAL VALVE PART DESCRIPTION1719 PILOTREPLACEMENT PARTS SIT MILLIVOLT VALVESIT MILLIVOLT REPLACEMENT PARTS FOR EMBER STOVE BASE ESB SIT MILLIVOLT 10 one is not available, you may contactPage LIMITED WARRANTY VENT-FREE GAS LOG HEATER NEW BUCK CORPORATIONPage