New Buck Corporation 384 manual Section, Fireplace Preparation

Page 8

SECTION II

SECTION II

FIREPLACE PREPARATION

The fireplace needs to be prepared before installing the heater.

A.Turn off the gas supply to the fireplace.

B.Read the following sections before installing your unit; Section III, page 20 Installation In A Solid-Fuel Burning Fireplace and Section VIII, page 31 Producing Adequate Ventilation.

NOTE: “IF THE FACTORY BUILT FIREPLACE HAS NO GAS ACCESS HOLE(S) PROVIDED, AN ACCESS HOLE OF 1.5 inch (37.5mm) DIAMETER OR LESS MAY BE DRILLED THROUGH THE LOWER SIDES OR BOTTOM OF THE FIREBOX IN A PROPER WORKMANLIKE MANNER. THIS ACCESS HOLE MUST BE PLUGGED WITH NON-COMBUSTIBLE INSULATION AFTER THE GAS SUPPLY LINE HAS BEEN INSTALLED.”

REFRACTORY, GLASS DOORS , SCREEN RAILS, SCREEN MESH AND SOLID-FUEL LOG GRATES (IF APPLICABLE) CAN BE REMOVED FROM THE FIREPLACE BEFORE INSTALLING THE UNVENTED FIREPLACE INSERT.

Page 4

Image 8

Contents MODEL VENT-FREEManufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS 6. What To Do IF You Smell Gas Shut off gas supply 32. This appliance is intended for supplemental heating SECTION FIREPLACE PREPARATIONFLAME INSTALLATION AND CLEARANCESGAS CONNECTION Page “MILLIVOLT ONLY” GAS PRESSURE CHECK FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTION MODULATING OR MANUAL VALVE SITLIGHTING INSTRUCTION to “ON” position. Continue to turn the to your desired setting 12. Close access panel door13. Turn on all electrical power to the appliance MANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONOPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS SIT-MILLIVOLT VALVE Page Page MANUAL LIGHTING PROCEDURE CR 3329 LOG SET WHEN USED AS A HEATING APPLIANCE HEAT OUTPUTFLAME CHECK WIRING DIAGRAM NOTE #PE SBR084 Blower Motor Rating 120 volts/60HZ/1.1 Amps CEILING SECTION INSTALLATION MODEL 384 FP IN SOLID FUEL BURNING FIREPLACESTrim Kit Also provide adequate clearances around air openings SECTION INSTALLATION OF MODEL 384 WS WITH OPTIONAL WOODEN SURROUND KIT#PAKDM384STEP 7 Remove cloth or blanket from underneath stove SECTION ZERO CLEARANCE INSTALLATION OF MODEL 384 ZC CHOOSING THE LOCATION FOR YOUR FIREPLACEGAS LINE DRAFTSZERO CLEARANCE STANDOFFS ASSEMBLY “Follow the instructions given in the diagrams below exactly”Top Standoff 2 per unit 12.50” Front Of Top Trim PanelINSTALLING THE FIREBOX FIREPLACE CLEARANCESInstall the Firebox Framing the FireboxFINISHING YOUR FIREPLACE CLEARANCESSECTION MODEL 384 FS FREESTANDING INSTALLATION FREESTANDING PEDESTAL OR LEGS INSTALLATION SECTION MODEL ALCOVE INSTALLATION CAUTION READ ENTIRE MANUAL BEFORE INSTALLING HEATERThis section is for residential or manufactured mobile installation SECTION PRODUCING ADEQUATE VENTILATIONDETERMINING FRESH-AIR FLOW FOR HEATER LOCATION 1. Determine the volume of the space length x width x height SECTION VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDINGVENTILATION AIR FROM OUTDOORS Ventilation Air From OutdoorsSECTION AFTER MARKET MOBILE HOME INSTALLATION IMPORTANT SAFEGUARDS CLEANINGOBSERVED Air in gas lines when OBSERVED OBSERVED REPAIR PARTS SERVICINGREPLACEMENT PARTS SIT MODULATING OR MANUAL VALVEKEY# PART DESCRIPTION1719 PILOTREPLACEMENT PARTS SIT MILLIVOLT VALVESIT MILLIVOLT REPLACEMENT PARTS FOR EMBER STOVE BASE ESB SIT MILLIVOLT 10 one is not available, you may contactPage LIMITED WARRANTY VENT-FREE GAS LOG HEATER NEW BUCK CORPORATIONPage